Sub-Zero 427R Wine Storage Installation Instructions

Sub-Zero 427R Manual

Get Sub-Zero 427R PDF manuals and user guides View all Sub-Zero 427R manuals
Add to My Manuals
Save this manual to your list of manuals

Sub-Zero 427R manual content summary:

  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 1
    INSTALLATION GUIDE Wine Storage
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 2
    Contents Wine Storage 3 Models 424G and 424FSG Installation 4 Models 427G and 427RG Installation 16 Model WS-30 Installation 30 Installation Checklist 54 Service Information 55 Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 3
    Storage 3 subzero.com Sub-Zero Wine Storage The importance of the installation of the Sub-Zero wine storage unit cannot be overemphasized. Installation should be done by a qualified installer. Before you begin the installation process, it is recommended that you read this entire installation guide
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 4
    424G and 424FSG Installation Models 424G and 424FS OVERALL DIMENSIONS 237/8" (606) 24" (610) 34" (864) 4" (102) 4 241/4" (616) 24 5/8" (625) 34 3/16" (868) 4" (102) 253/8" (645) MODEL 424G 13/4" (44) Door swing clearances are based on stainless steel door and handle dimensions. 253
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 5
    and 424FSG Installation 5 subzero.com Models 424G and 424FSG Installation The model 424FSG wine storage unit is designed to be attractive in a stand alone setting. Model 424G must be built in. Refer to the previous page for overall dimensions and door swing clearances for models 424G and 424FS
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 6
    servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. IMPORTANT NOTE: For model ground prong. Electrical Requirements Power Supply Circuit Breaker Receptacle LEFT SIDE OF OPENING 2" (51) 151/2" (394) 3" (76
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 7
    Models 424G and 424FSG Installation 7 subzero This is for a lowvoltage, low-current signal similar to door and window sensor signals. Common, normally open and normally for servicing. Use an appliance dolly to move the wine storage unit near the installation opening. Position the dolly at the side
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 8
    wine storage unit. The anti-tip bracket must be installed on a solid base to prevent tipover in case several loaded wine shelves are extended at the same time. MODEL 424FSG If you are installing the model door, to the back of the antitip bracket. Refer to the illustration below. MODEL the sides and
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 9
    424G and 424FSG Installation 9 subzero.com Anti-Tip Bracket Installation MODEL 424FSG-WOOD FLOORS Use the four #12 x 21/2" of 3/4" (19). Be sure that the screws hold tight. Refer to the illustration below. MODEL 424FSG-CONCRETE FLOORS Use the two 3/8" x 33/4" concrete wedge anchors, two #12 x 21
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 10
    unit. The accessory lock kit and additional instructions are available through your authorized Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com. IMPORTANT NOTE: If for any reason the wine storage unit has been laid on its back or side, you must allow
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 11
    model 424G, the countertop bracket should be used to make a solid installation. Refer to the illustration on page 8. If this is not possible, wedge shims along the sides . If a home alarm system is to be installed on the wine storage unit, the connections should be made using the logic supplied with
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 12
    , a special high altitude glass door unit (HAG) must be ordered. If you have questions, contact your authorized Sub-Zero dealer or cabinet supplier. Additional panel information can be found in the Sub-Zero design guide. A solid panel cannot be installed over the glass door, as this may cause
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 13
    Installation 13 subzero.com Overlay Door Panel MODEL 424G Inspect the door panel for the minimum 5/8" (16) thickness, the finished inside edge. The glass door has a 10 lbs (5 kg) weight limit. Refer to the wine storage section of the Sub-Zero design guide for additional panel information. Decide
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 14
    member requires the support provided by the glass door. After the door panel installation is complete, apply the cover patches or plugs provided over the holes on the inside surface of the door. The cover patches or plugs are part of the insulation system on the door of the wine storage unit. Be
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 15
    hinge screws to adjust the door. Complete the Installation When you have completed installation of the model 424G or 424FSG wine storage unit, refer to page 54 for an installation checklist and page 55 for service information. TOP DOOR HINGE SHIPPING SCREWS BOTTOM DOOR HINGE SHIPPING SCREWS Top
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 16
    ) 9 3/4" (248) 4" (102) 24" (610) 45/8" (117) 251/2" (648) 24" (610) 191/2" (495) 45/8" (117) 251/2" (648) DIMENSIONS WILL VARY WITH PANEL THICKNESS MODEL 427G Overall dimensions do not include panels or handles. DIMENSIONS WILL VARY WITH PANEL THICKNESS MODEL 427RG WITH BULK STORAGE DRAWERS
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 17
    dimensions illustrations for models 427G and 427R on the previous page. IMPORTANT NOTE: The floor under the wine storage unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing. IMPORTANT NOTE: To operate properly, the door must open a minimum
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 18
    servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. IMPORTANT NOTE: For models V AC, 60 Hz 15 amp 3-prong grounding-type LEFT SIDE OF OPENING 21/2" (64) 13" (330) 41/2" (114) 1/4" FLOOR (6)
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 19
    is for a lowvoltage, low-current signal similar to door and window sensor signals. Common, normally open and wine storage unit. The anti-tip bracket must be installed on a solid base to prevent tipover in case several loaded wine shelves are extended at the same time. If you are installing the model
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 20
    Models 427G and 427RG Installation 20 Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS Use the six #12 x 21/2" wood screws and the six 1/4" flat washers provided.
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 21
    heater kit and additional instructions is available through your authorized Sub-Zero dealer, or call Sub-Zero customer care at 800-222-7820. You can also visit our website at subzero.com. LOCK INSTALLATION For models 427G and 427RG, the optional lock is attached to the decorative door panel through
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 22
    Models wine storage unit near the rough opening. Position the dolly at the side the wine storage unit has been laid on its back or side, proceed. Pre-level the wine storage unit before moving into position be used with the wine storage unit, the lead wires easier. When the wine storage unit is installed
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 23
    Models 427G and 427RG Installation 23 subzero.com Level the Unit Level the wine storage unit by turning the front leveling the side molding can be attached. The top molding strip is held in place by double-sided velcro. The side molding strips snap into place over brackets attached to the side of
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 24
    should be completed. If the dual installation heater kit is used with model 427G or 427RG, the power supply leads should be connected according to instructions included with the kit. If a home alarm system is to be installed on the wine storage unit, the connections should be made using the
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 25
    ordered. If you have questions, contact your authorized Sub-Zero dealer or cabinet supplier. Additional panel information can be found in the Sub-Zero design guide, or visit our website at subzero.com. A solid panel cannot be installed over the glass door, as this may cause moisture to form behind
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 26
    Refer to the wine storage section of the Sub-Zero design guide for additional panel information. Decide if the handle will be attached through the glass door frame or just through the decorative door panel. If it is just through the door panel, the handle must be attached first. If a lock is to be
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 27
    rim and no connecting center member requires the support provided by the glass door. After the door panel installation is complete, apply the cover patches or plugs provided over the holes on the inside surface of the door. The wine storage unit door is made with a sealed double wall tempered glass
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 28
    427RG IMPORTANT NOTE: Drawer panels for model 427RG must be a minimum of 5/8" (16) thick and cannot exceed 12 lbs (5 kg) for each panel. Remove the mounting hardware provided and set aside. As with the door panel, you should work on the back side of each drawer panel to protect the front surface
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 29
    or integrated units together. The kit is available through your authorized Sub-Zero dealer, or call Sub-Zero customer care at 800-222-7820. You can also visit our website at subzero.com. OPTIONAL 90° DOOR STOP The door of models 427G and 427RG opens to 105°. A 90° door stop is built into the hinge
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 30
    you receive does not match your requirements, contact your authorized Sub-Zero dealer. The model WS-30 wine storage unit offers the following design alternatives: framed, overlay, flush inset and stainless steel models. The overlay model has two design applications, overlay and flush inset. Each of
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 31
    Model WS-30 Installation 31 subzero.com Site Preparation Make sure that the finished rough opening where the wine storage unit is being using custom panels or Sub-Zero accessory flush inset panels. If you are installing two models WS-30, or a model WS-30 and a built-in unit side by side in the
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 32
    Model WS-30 Installation 32 Standard Installation Opening Dimensions Framed, Overlay and Stainless Steel Models 24" (610) OPENING DEPTH TOP VIEW 24" (610) OPENING DEPTH 83 3/4" (2127) OPENING HEIGHT 291/2" (746) OPENING WIDTH SIDE VIEW FRONT VIEW IMPORTANT NOTE: If two units are installed
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 33
    Model WS-30 Installation 33 subzero.com Flush Inset Installation Opening Dimensions 26 3/16" 24" (610) Detail B 11/4" (32) SIDE VIEW DETAIL B FRONT VIEW IMPORTANT NOTE: Dimensions assume a 3/4" (19) panel thickness. IMPORTANT NOTE: If two units are installed side by side, refer to page 35 for
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 34
    VIEW 24" (610) OPENING DEPTH 83 3/4" (2127) OPENING HEIGHT A OPENING WIDTH SIDE VIEW Opening Widths Two 30" (762) Models Model WS-30 and a 36" (914) Model FRONT VIEW A 593/4" (1518) 653/4" (1670) IMPORTANT NOTE: A dual installation kit will be required for this installation. Stainless steel
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 35
    Model WS-30 Installation 35 subzero.com Dual SIDE VIEW FRONT VIEW DETAIL B Opening Widths Two 30" (762) Models Model WS-30 and a 36" (914) Model A B 593/4" (1518) 621/4" (1581) 653/4" (1670) 681/2" (1740) IMPORTANT NOTE: Dimensions assume a 3/4" (19) panel thickness. A dual installation kit
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 36
    Model WS-30 Installation 36 Electrical Requirements For model WS-30, the electrical supply should be located within the shaded area shown in the illustration. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. A separate circuit, servicing only this
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 37
    Model WS-30 Installation 37 subzero.com Anti-Tip Bracket Installation To prevent the unit of 4" (102) from the sides of the rough opening. This depth will increase to 263/16" (665) for a flush inset installation based on 3/4" (19) deep decorative panels. Proper placement will ensure that the
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 38
    Model WS-30 Installation 38 Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS After properly locating the anti-tip brackets in the rough opening, drill pilot holes 3/16" (5) diameter maximum in the wall studs and/or wall plate. Use the #12 x 21/2" PH pan HD zinc screws and #12 flat washers to
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 39
    Model WS-30 Installation 39 subzero.com Unpack the Unit Uncrate the wine storage unit and inspect for any door and bottom of the grille. To eliminate potential interference of the grille and hinge, the grille height can be adjusted. Loosen the four grille adjustment screws (two on each side)
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 40
    and protect any finished flooring. Use an appliance dolly to move the unit near the rough opening. Model WS-30 is equipped with rollers, so it can be moved into position more easily. If possible, keep the door closed until the unit is properly anchored. IMPORTANT NOTE: If for any reason the unit has
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 41
    Model WS-30 Installation 41 subzero.com Door Adjustment The door of the model WS-30 can be adjusted in three ways: In and out, side to side tilt, and up and down. Regardless of the adjustment being made, start by slightly loosening the two upper hinge bolts on the upper hinge plate
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 42
    Model WS-30 Installation 42 Panel Installation If your customer has ordered either a framed or overlay model, you will be installing a door panel to give the unit the custom Sub-Zero look. Before you begin installing the panel, refer to the panel specifications for framed, overlay or flush inset
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 43
    outlet. OPTIONAL 90° DOOR STOP The door of the model WS-30 opens to 110°. A 90° door stop is provided with the unit (located behind the grille) for installations where the door opening must be limited. Additional 90° door stop kits are available through your authorized Sub-Zero dealer. The 90
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 44
    dimensions listed in the framed panel specifications on the following page. Additional panel design information can be found in the Sub-Zero design guide and on our website, subzero.com. If the thickness of the custom panel is less than a 1/4" (6), back it up with a sheet of shim material to build
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 45
    must not exceed 75 lbs (34 kg). A solid panel cannot be installed over the glass door, as this may cause moisture to form behind the panel. Framed Panel Specifications A A A H A W Model WS-30 DOOR Door Panel WINDOW Cut-Out Location W 293/4" (756) W 231/2" (597) H 699/16" (1767) H 635/16
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 46
    in the Sub-Zero design guide and on our website, subzero.com. IMPORTANT NOTE: The size of the overlay panel is critical. It must fit over the door frame. The weight of the overlay panel must not exceed 75 lbs (34 kg) and the panel must be a minimum of 5/8" (16) thick. Overlay models are shipped
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 47
    problems with the operation of the Sub-Zero unit. A solid panel cannot be installed over the glass door, as this may cause moisture to form behind the panel. Overlay Panel Specifications H A A A H A W Model WS-30 DOOR Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 48
    in the Sub-Zero design guide and on our website, subzero.com. IMPORTANT NOTE: The size of the flush inset panel is critical. It must fit over the door frame. The weight of the overlay panel must not exceed 75 lbs (34 kg) and the panel must be a minimum of 5/8" (16) thick. Overlay models are shipped
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 49
    to the compressor area and cause problems with the operation of the Sub-Zero unit. Flush Inset Panel Specifications H A A A H A W Model WS-30 DOOR Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel WINDOW Cut-Out Location W 31" (787) 291/8" (740
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 50
    When two models WS-30 or a model WS-30 and built-in unit are installed side by side, a dual installation kit may be required. Contact your authorized Sub-Zero dealer for the proper components and installation instructions. For questions relative to the installation, call Sub-Zero at 800
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 51
    your authorized Sub-Zero dealer. Refer to the illustration and chart for dual flush inset panel specifications. Flush Inset Panels-Dual Installation H A A A H A W Model WS-30 DOOR Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel WINDOW Cut-Out
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 52
    damage to SIDE VIEW DOOR 3/32" 5/16" (2) (8) SIDE VIEW S the panels and the Sub-Zero unit. Illus. C Illus. D Panel Offsets WS-30 Doors (hinge) / Grille Sides Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom Illus. A B C D E DOOR / S DRAWER 5/16" (8) SIDE VIEW 3/32
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 53
    . When installing a model WS-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through your authorized Sub-Zero dealer. Refer to instructions included with the side panel kit when installing these side panels. For local dealer
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 54
    (model WS-30)? Are panels attached securely and properly aligned? Has the door been service problems been noted on the product registration card? Has the registration card been mailed in? Have stainless steel panels been inspected for any imperfections? This is to be done by the authorized Sub-Zero
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 55
    , maintain the quality built into your wine storage unit by calling Sub-Zero factory certified service. For the name and number of Sub-Zero factory certified service nearest you, check the contact & support section of our website, subzero.com or call Sub-Zero customer care at 800-222-7820. When
  • Sub-Zero 427R | Wine Storage Installation Instructions - Page 56
    SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7022655 REV-A 9/2011
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
INSTALLATION GUIDE
Wine Storage