Sub-Zero 427R Wine Storage Installation Instructions - Page 46

Model WS-30 Installation, Overlay Panels

Get Sub-Zero 427R PDF manuals and user guides View all Sub-Zero 427R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Model WS-30 Installation 46 Overlay Panels If your customer has chosen an overlay design application, make sure that the panels you are about to install match dimensions listed in the overlay panel specifications on the following page. Additional panel design information can be found in the Sub-Zero design guide and on our website, subzero.com. IMPORTANT NOTE: The size of the overlay panel is critical. It must fit over the door frame. The weight of the overlay panel must not exceed 75 lbs (34 kg) and the panel must be a minimum of 5/8" (16) thick. Overlay models are shipped without handle hardware. The cabinet manufacturer or designer will need to provide handle hardware to match the overall decorating scheme. To install overlay panels, first remove the door trim molding. Insert a screwdriver tip into the top corner slot on the handle side and pop out the trim molding. Refer to the illustration on page 44. Remove the screws and frame. Sub-Zero allows a 1/4" (6) space to slide the backing material into place in the frame. If your material is thicker than a 1/4" (6), either rout an edge around the panel to get a proper fit or mount the decorative overlay panel on a sheet of 1/4" (6) thick material and insert the backing material into the channel. You must allow for .10" (3) space between the backer board and the decorative panel, so the panel will slide easily into the door frame. The illustrations below provide a cross section view of the three panel assembly showing placement of the trim and a rear view of the three panel assembly with critical dimensions, standard for all models. Install the handle hardware before inserting the panel. We recommend a larger D-style pull. The use of a small, onepiece knob is not recommended. If you use screws with thick heads, you will need to countersink the screws into the backer panel before sliding the assembly into place. Slide the panel into the frame on the door. With the panel in position, replace the frame end. Be sure the panel is inserted completely into the channel for proper fit and alignment. To reinstall the trim molding, insert the top of the trim molding into the grooves at the top of the door and work downward, snapping the trim molding into the clips on the frame. SPACER PANEL OVERLAY PANEL BACKER PANEL TRIM 5/16" (8) min 1/8" (3) Panel assembly cross section. OVERLAY PANEL SPACER PANEL BACKER PANEL 3/4" (19) typical .10" (3) 1/4" (6) Panel assembly rear view.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Model WS-30 Installation
46
Overlay Panels
If your customer has chosen an overlay design applica-
tion, make sure that the panels you are about to install
match dimensions listed in the overlay panel specifica-
tions on the following page. Additional panel design infor-
mation can be found in the Sub-Zero design guide and on
our website, subzero.com.
IMPORTANT NOTE:
The size of the overlay panel is
critical. It must fit over the door frame. The weight of the
overlay panel must not exceed 75 lbs
(34 kg)
and the panel
must be a minimum of
5
/
8
"
(16)
thick.
Overlay models are shipped without handle hardware. The
cabinet manufacturer or designer will need to provide
handle hardware to match the overall decorating scheme.
To install overlay panels, first remove the door trim
molding. Insert a screwdriver tip into the top corner slot on
the handle side and pop out the trim molding. Refer to the
illustration on page 44. Remove the screws and frame.
Sub-Zero allows a
1
/
4
"
(6)
space to slide the backing
material into place in the frame. If your material is thicker
than a
1
/
4
"
(6)
, either rout an edge around the panel to get
a proper fit or mount the decorative overlay panel on a
sheet of
1
/
4
"
(6)
thick material and insert the backing
material into the channel.
You must allow for .10"
(3)
space between the backer
board and the decorative panel, so the panel will slide
easily into the door frame.
The illustrations below provide a cross section view of the
three panel assembly showing placement of the trim and a
rear view of the three panel assembly with critical dimen-
sions, standard for all models.
Install the handle hardware before inserting the panel. We
recommend a larger D-style pull. The use of a small, one-
piece knob is not recommended. If you use screws with
thick heads, you will need to countersink the screws into
the backer panel before sliding the assembly into place.
Slide the panel into the frame on the door. With the panel
in position, replace the frame end. Be sure the panel is
inserted completely into the channel for proper fit and
alignment.
To reinstall the trim molding, insert the top of the trim
molding into the grooves at the top of the door and work
downward, snapping the trim molding into the clips on the
frame.
1
/
8
"
(3)
OVERLAY PANEL
SPACER PANEL
BACKER PANEL
TRIM
5
/
16
"
(8) min
Panel assembly cross
section.
Panel assembly rear view.
1
/
4
"
(6)
.10"
(3)
OVERLAY
PANEL
SPACER
PANEL
BACKER
PANEL
3
/
4
"
(19)
typical