Sub-Zero 427R Wine Storage Installation Instructions - Page 10

Models 424G and 424FSG Installation, Position the Unit - accessories

Get Sub-Zero 427R PDF manuals and user guides View all Sub-Zero 427R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Models 424G and 424FSG Installation 10 Position the Unit If you are adding an accessory lock kit to your wine storage unit, it should be installed before you position the unit. The accessory lock kit and additional instructions are available through your authorized Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com. IMPORTANT NOTE: If for any reason the wine storage unit has been laid on its back or side, you must allow the unit to stand upright for a minimum of 24 hours before connecting power. Plug the power cord into the grounded electrical outlet. With power applied to the appliance, check for lighting and cooling before going any further. Once you are satisfied that the unit is operating properly, shut off power to the electrical outlet at the circuit breaker and proceed. Pre-level the wine storage unit before sliding it into position. Leveling cannot be completed with the unit pushed back in the installation opening. If a home alarm system is to be used with the wine storage unit, the lead wires should be threaded into the compressor compartment before you position the unit. Refer to home alarm connections on the following page, for the location of these lead wires. After the unit is in position, the alarm wiring can be completed from the front. For model 424FSG, adust the leveling legs so the top of the unit is no more than 345/8" (879) above the floor. This is to allow the unit to engage the anti-tip bracket properly. Center the model 424FSG in front of the anti-tip bracket. Slide the unit into position, making sure the anti-tip bracket is engaged properly. When the wine storage unit is installed, the anti-tip bracket will be positioned just below the engaging bracket on the unit. It is not necessary to raise the unit up so that it locks into the anti-tip bracket, but the unit must be in alignment with the anti-tip bracket. The wine storage unit provides the best access to its contents when the front surface of the door panel extends out from surrounding cabinets approximately 1/4" (6). For model 424FSG, if there are no surrounding cabinet surfaces to gauge depth, slide the unit back until it engages the anti-tip bracket. IMPORTANT NOTE: The floor under the wine storage unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Models 424G and 424FSG Installation
10
Position the Unit
If you are adding an accessory lock kit to your wine
storage unit, it should be installed before you position the
unit. The accessory lock kit and additional instructions are
available through your authorized Sub-Zero dealer, or call
Sub-Zero at 800-222-7820. You can also visit our website
at subzero.com.
IMPORTANT NOTE:
If for any reason the wine storage unit
has been laid on its back or side, you must allow the unit
to stand upright for a minimum of 24 hours before con-
necting power.
Plug the power cord into the grounded electrical outlet.
With power applied to the appliance, check for lighting
and cooling before going any further. Once you are satis-
fied that the unit is operating properly, shut off power to
the electrical outlet at the circuit breaker and proceed.
Pre-level the wine storage unit before sliding it into
position. Leveling cannot be completed with the unit
pushed back in the installation opening.
If a home alarm system is to be used with the wine
storage unit, the lead wires should be threaded into the
compressor compartment before you position the unit.
Refer to home alarm connections on the following page,
for the location of these lead wires. After the unit is in
position, the alarm wiring can be completed from the front.
For model 424FSG, adust the leveling legs so the top of
the unit is no more than 34
5
/
8
"
(879)
above the floor. This is
to allow the unit to engage the anti-tip bracket properly.
Center the model 424FSG in front of the anti-tip bracket.
Slide the unit into position, making sure the anti-tip
bracket is engaged properly.
When the wine storage unit is installed, the anti-tip
bracket will be positioned just below the engaging bracket
on the unit. It is not necessary to raise the unit up so that
it locks into the anti-tip bracket, but the unit must be in
alignment with the anti-tip bracket.
The wine storage unit provides the best access to its
contents when the front surface of the door panel extends
out from surrounding cabinets approximately
1
/
4
"
(6)
. For
model 424FSG, if there are no surrounding cabinet
surfaces to gauge depth, slide the unit back until it
engages the anti-tip bracket.
IMPORTANT NOTE:
The floor under the wine storage unit
must be at the same level as the surrounding finished floor
to allow for removal of the unit for servicing.