TP-Link T1500G-8T T1500G-10PSUN V1 CLI Reference Guide Guide
TP-Link T1500G-8T Manual
 |
View all TP-Link T1500G-8T manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1500G-8T manual content summary:
- TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 1
CLI Guide JetStream 8-Port Gigabit Smart Switch T1500G-10MPS/T1500G-8T (TL-SG2008) T1500G-10PS (TL-SG2210P) REV1.0.2 1910012064 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 3
1.4.3 Parameter Format 15 Chapter 2 User Interface 16 2.1 enable ...16 2.2 enable-admin ...16 2.3 service password-encryption 17 2.4 enable password ...18 2.5 enable secret...19 2.6 configure ...20 2.7 exit ...20 2.8 end ...21 2.9 history ...21 2.10 history clear...22 Chapter - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 4
43 6.1 user name (password 43 6.2 user name (secret 44 6.3 user access-control ip-based 45 6.4 user access-control mac-based 46 6.5 user access-control port-based 47 6.6 telnet ...48 6.7 show user account-list 48 6.8 show user configuration 49 6.9 show telnet-status - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 5
key 58 7.11 show ip http configuration 59 7.12 show ip http secure-server 59 Chapter 8 Binding Table Commands 61 8.1 ip source binding ...61 8.2 ip dhcp snooping ...62 8.3 ip dhcp snooping vlan 63 8.4 ip dhcp snooping information option 64 8.5 ip dhcp snooping information strategy - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 6
show logging flash 90 Chapter 12 SSH Commands 91 12.1 ip ssh server...91 12.2 ip ssh version ...91 12.3 ip ssh algorithm ...92 12.4 ip ssh timeout ...93 12.5 ip ssh max-client ...93 12.6 ip ssh download ...94 12.7 remove public-key 95 12.8 show ip ssh ...95 Chapter 13 IEEE 802.1X Commands 97 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 7
119 show mac address-table security 120 Chapter 15 System Configuration Commands 121 15.1 15.2 15.3 15.4 15.5 15 18 15.19 15.20 15.21 system-time manual 121 system-time ntp...121 system-time dst 127 contact-info...127 ip address ...128 ip address-alloc ...129 reset ...130 reboot ...130 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 8
140 show cpu-utilization 141 show memory-utilization 141 Chapter 16 Ethernet Configuration Commands 143 16.1 16.2 16.3 16.4 16.5 16.6 16.7 149 show interface status 150 show interface counters 151 show interface configuration 151 show storm-control 152 show bandwidth ...153 Chapter 17 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 9
-list bind(interface 179 access-list bind(vlan 180 show access-list ...181 show access-list policy 181 show access-list bind 182 Chapter 22 PoE Commands 183 22.1 power inline consumption (global 183 22.2 power profile...184 22.3 power time-range 185 22.4 absolute ...185 VIII - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 10
inline priority 190 power inline supply 191 power inline profile 191 power inline time-range 192 show power inline 193 show power inline configuration interface 193 show power inline information interface 194 show power profile 194 show power holiday 195 show power time-range 195 Chapter - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 11
24.29 24.30 24.31 ip igmp snooping(global 215 ip igmp snooping(interface 215 ip igmp snooping rtime 216 ip igmp snooping mtime 217 ip igmp snooping report-suppression 217 ip igmp snooping immediate-leave 218 ip igmp snooping drop-unknown 218 ip igmp snooping last-listener query-inteval 219 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 12
239 snmp-server user 241 snmp-server community 242 snmp-server host 243 snmp-server engineID 245 snmp-server traps snmp 245 snmp-server traps link-status 246 snmp-server traps 247 snmp-server traps vlan 248 rmon history ...249 rmon event ...250 rmon alarm ...251 rmon statistics ...252 show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 13
enable admin password 272 enable default 282 show aaa authentication 283 show aaa accounting 284 line telnet...284 login authentication(telnet 285 line ssh ...285 login authentication(ssh 286 enable authentication(telnet 287 enable authentication(ssh 287 ip http login authentication 288 ip - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 14
Guide stands for T1500G-10MPS/T1500G-8T/T1500G-10PS JetStream 8-Port Gigabit Smart Switch for configuring LAG (Link Aggregation Group) and LACP (Link Aggregation configuring the HTTP and HTTPS logon. Chapter 8: Binding Table Commands Provide information about the commands used for binding the IP - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 15
Provide information about the commands used for Address configuration. Chapter 15: System Configuration Commands Provide information about the commands used for configuring the System information and System IP, reboot and reset the switch, upgrade the switch system and commands used for cable test - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 16
Chapter 25: SNMP Commands Provide information about the commands used for configuring the SNMP (Simple Network Management Protocol) functions. Chapter 26: LLDP Commands Provide information about the commands used for configuring LLDP function. Chapter 27: AAA Commands Provide information about the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 17
an Ethernet port. 1.1.1 Logon by Telnet To log on to the switch by a Telnet connection, please take the following steps: 1. Click Start window and press the Enter button. Figure 1-1 Run Window 2. Telnet the switch's IP address (factory setting is 192.168.0.1) in the prompt cmd window and press Enter. - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 18
. There are two authentication modes to set up an SSH connection: Password Authentication Mode: It requires username and password, which are both admin by default. Key Authentication Mode: It requires a public key for the switch and a private key for the SSH client software. You can generate - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 19
Figure 1-5 Enable SSH function Password Authentication Mode 1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type. Figure 1-6 SSH Connection Config 6 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 20
button in the above figure to log on to the switch. Enter the login user name and password to log on the switch, and then enter enable to enter Privileged EXEC Mode, so you can continue to configure the switch. Figure 1-7 Log on the Switch Key Authentication Mode 1. Select the key type and key - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 21
key is successfully generated, please save the public key and private key to a TFTP server. Figure 1-9 Save the Generated Key 3. Log on to the switch by Telnet and download the public key file from the TFTP server to the switch, as the following figure shows: Figure 1-10 Download the Public Key 8 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 22
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading can not be interrupted. 4. After the public key is downloaded, please log on to the interface of PuTTY and enter the IP address for login. Figure 1-11 SSH Connection Config 9 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 23
to the switch without entering password, it indicates that the key has been successfully downloaded. Figure 1-13 Log on the Switch 1.2 CLI Command Modes The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode and - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 24
command to enter this mode from User EXEC mode. Global Configuration Mode Use the configure command to enter this mode from Privileged EXEC mode. T1500G-10MPS> T1500G-10MPS# T1500G-10MPS(config)# Use the exit command to disconnect the switch. Use the enable command to access Privileged EXEC mode - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 25
mode. Use the interface loopback id command to enter Loopback Interface mode from Global Configuration mode. T1500G-10MPS(config-if)# or T1500G-10MPS(config-if-range)# Use the switchport command to switch to the Layer 2 interface mode. Use the end command or press Ctrl+Z to return to Privileged - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 26
next mode T1500G-10MPS(config-vlan)# Use the end command or press Ctrl+Z to return to Privileged EXEC mode. Enter the exit command or the # command to return to Global configuration mode. Note: 1. The user is automatically in User EXEC Mode after the connection between the PC and the switch is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 27
Privileged EXEC mode from User EXEC mode by using the enable command. In default case, no password is needed. In Global Configuration Mode, you can configure password for Admin level by enable password command. Once password is configured, you are required to enter it to access Privileged EXEC mode - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 28
1.4.3 Parameter Format Some parameters must be entered in special formats which are shown as follows: MAC address must be enter in the format of xx:xx:xx:xx:xx:xx. One or several values can be typed for a port-list or a vlan-list using comma to separate. Use a hyphen to designate a range of - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 29
EXEC Mode from User EXEC Mode: T1500G-10MPS>enable Enter password： T1500G-10MPS# 2.2 enable-admin Description The enable-admin command is used to evaluate the current log-in user to the Admin access level. Syntax enable-admin Command Mode Privileged Configuration Mode Privilege Requirement None. 16 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 30
123 to gain the administrative privilege. T1500G-10MPS#enable-admin Password:123 T1500G-10MPS# 2.3 service password-encryption Description The service password-encryption command is used to encrypt the password when the password is defined or when the configuration is written, using the symmetric - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 31
characters By default, it is empty. 7 -- Indicates a symmetric encrypted password with fixed length will follow. encrypted-password -- A symmetric encrypted password with fixed length, which you can copy from another switch's configuration file. After the encrypted password is configured, you - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 32
default, it is empty. The password in the configuration file will be displayed in the MD5 encrypted form. 5 -- Indicates an MD5 encrypted password with fixed length will follow. encrypted-password -- An MD5 encrypted password with fixed length, which you can copy from another switch's configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 33
from User EXEC Mode. The password will be displayed in the encrypted form. T1500G-10MPS(config)#enable secret 0 admin 2.6 configure Description The configure command is used to access Global Configuration Mode from Privileged EXEC Mode. Syntax configure Command Mode Privileged EXEC Mode Privilege - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 34
Configuration Mode from Interface Configuration Mode, and then return to Privileged EXEC Mode: T1500G-10MPS(config-if)# exit T1500G-10MPS(config)#exit T1500G Return to Privileged EXEC Mode from Interface Configuration Mode: T1500G-10MPS(config-if)#end T1500G-10MPS# 2.9 history Description The history - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 35
Command Mode Privileged EXEC Mode and any Configuration Mode Privilege Requirement None. Example Show the commands you have entered in the current mode: T1500G-10MPS (config)# history 1 history 2.10 history clear Description The history clear command is used to clear the commands you have entered in - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 36
technology is developed for the switch to divide the LAN into used to create IEEE 802.1Q VLAN and enter VLAN Configuration Mode. To delete the IEEE 802.1Q VLAN, please of 2-3, 5. It is multi-optional. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 37
VLAN ID, ranging from 1 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create VLAN Interface 2: T1500G-10MPS(config)# interface vlan 2 3.3 name Description The name command - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 38
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Add port 4 it to VLAN 2 and configure the type of port 1/0/4 as tagged: T1500G-10MPS(config)# interface gigabitEthernet 1/0/4 T1500G-10MPS(config-if)# switchport general allowed vlan 2 tagged 25 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 39
configure the PVID for the switch ports. Syntax switchport pvid vlan-id Parameter vlan-id -- VLAN ID, ranging from 1 to 4094. Command Mode Interface Configuration Specify the PVID of port 1/0/2 as 2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# switchport pvid 2 3.6 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 40
of IEEE 802.1Q VLAN. Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the brief information of IEEE 802.1Q VLAN: T1500G-10MPS(config)# show vlan brief 3.8 show vlan Description The show vlan command is used to display - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 41
| port-channel lagid ] Parameter port -- The port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the VLAN configuration information of all ports and LAGs: T1500G-10MPS(config)# show interface switchport 28 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 42
, you can perform QoS-related configuration for voice data, ensuring the ranging from 2 to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User Example Enable the Voice VLAN function for VLAN 10: T1500G-10MPS(config)# voice vlan 10 4.2 voice vlan - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 43
Set the aging time for the Voice VLAN as 1 minute: T1500G-10MPS(config)# voice vlan aging 1 4.3 voice vlan priority Description The voice vlan priority command is used to configure the priority for the Voice VLAN. To restore to the default priority, please use no voice vlan priority command. Syntax - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 44
for identification which contains 16 characters at most. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have described as TP-Phone with the OUI address 00:11:11:11:11:11 and the mask address FF:FF:FF:00:00:00: T1500G-10MPS(config)#voice - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 45
voice vlan mode { manual | auto } Parameter manual | auto -- Port mode. Command Mode Interface Configuration Mode (interface gigabitEthernet commands. Example Configure the port 1/0/3 to operate in the auto voice VLAN mode: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 46
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the configuration information of Voice VLAN globally: T1500G-10MPS(config)# show voice vlan 4.8 show voice vlan oui Description The show voice vlan oui command is used to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 47
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Display the configuration information of Voice VLAN OUI: T1500G-10MPS(config)# show voice vlan oui 4.9 show voice vlan switchport Description The show voice vlan switchport command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 48
Display the Voice VLAN configuration information of port 1/0/2: T1500G-10MPS(config)# show voice vlan switchport gigabitEthernet 1/0/2 35 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 49
Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 50
the Aggregate Arithmetic for LAG. To return to the default configurations, please use no port-channel load-balance command. Syntax port-channel load-balance { src-mac | dst-mac | src-dst-mac | src-ip | dst-ip | src-dst-ip } no port-channel load-balance Parameter src-mac -- The source MAC address - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 51
Arithmetic for LAG as "src-dst-ip": T1500G-10MPS(config)# port-channel load-balance src-dst-ip 5.3 lacp system-priority Description The lacp system-priority command is used to configure the LACP system priority globally. To return to the default configurations, please use no lacp system-priority - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 52
65535. It is 32768 by default. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range Configure the LACP port priority as 1024 for ports 1-3: T1500G-10MPS(config)# interface range gigabitEthernet 1/0/1-3 T1500G-10MPS(config-if-range)# lacp port-priority 1024 Configure - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 53
-group-num -- The EtherChannel Group number, ranging from 1 to 6. By default, it is empty, and will display the information of all EtherChannel Groups. detail and Any Configuration Mode Privilege Requirement None. Example Display the detailed information of EtherChannel Group 1: T1500G-10MPS(config - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 54
information. neighbor -- The neighbor LACP information. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the internal LACP information of EtherChannel Group 1: T1500G-10MPS(config)# show lacp 1 internal 5.8 show lacp sys-id Description The show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 55
Example Display the LACP system priority: T1500G-10MPS(config)# show lacp sys-id 42 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 56
the right to edit or modify. It is "admin" by default. For more details about privilege restrictions, please refer to the Privilege password with fixed length will follow. encrypted-password -- A symmetric encrypted password with fixed length, which you can copy from another switch's configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 57
encryption function is enabled in service password-encryption, the password in the configuration file will be displayed in the symmetric encrypted form. Example Add and enable a new admin user named "tplink", of which the password is "admin" and unencrypted: T1500G-10MPS(config)#user name tplink - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 58
encrypted algorithm. 5 -- Indicates an MD5 encrypted password with fixed length will follow. encrypted-password -- An MD5 encrypted password with fixed length, which you can copy from another switch's configuration file. Command Mode Global Configuration Mode Privilege Requirement Only Admin level - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 59
here are allowed to access the switch. ip-mask --The subnet mask of the IP address. [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ] -- Specify the access interface. These interfaces are enabled by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 60
are enabled by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure that only the user whose MAC address is 00:00:13:0A:00:01 is allowed to access the switch: T1500G-10MPS(config)# user - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 61
these commands. Example Configure that only the users connected to ports 2-6 are allowed to access the switch: T1500G-10MPS(config)# user command. This function is enabled by default. Syntax telnet enable telnet disable Command Mode Global Configuration Mode Privilege Requirement Only Admin and - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 62
commands. Example Display the information of the current users: T1500G-10MPS(config)# show user account-list 6.8 show user configuration Description The show user configuration command is used to display the security configuration information of the user authentication information and the access - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 63
Syntax show telnet-status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display whether the Telnet function is enabled: T1500G-10MPS(config)# show telnet-status 50 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 64
within the switch. To disable the HTTP function, please use no ip http server command. This function is enabled by default. The HTTP and HTTPS server function cannot be disabled at the same time. Syntax ip http server no ip http server Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 65
max-users command is used to configure the maximum number of users that are allowed to connect to the HTTP server. To cancel this limitation, please use no ip http max-users command. Syntax ip http max-users admin-num operator-num power-user-num user-num no ip http max-users Parameter admin - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 66
to these commands. Example Configure the timeout time of the HTTP server connection as 15 minutes: T1500G-10MPS(config)# ip http session timeout 15 7.4 ip http secure-server Description The ip http secure-server command is used to enable the HTTPS server within the switch. To disable the HTTPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 67
: T1500G-10MPS(config)# no ip http secure-server 7.5 ip http secure-protocol Description The ip http secure-protocol command is used to configure the SSL protocol version. To restore to the default SSL version, please use no ip http secure-protocol command. By default, the switch supports SSLv3 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 68
http secure-ciphersuite command is used to configure the cipherSuites over the SSL connection supported by the switch. To restore to the default ciphersuite types, please use no ip http secure-ciphersuite command. Syntax ip http secure-ciphersuite { [ 3des-ede-cbc-sha ] [ rc4-128-md5 ] [ rc4-128-sha - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 69
the HTTPS server as 5, 2, 2, and 1: T1500G-10MPS(config)# ip http secure-max-users 5 2 2 1 7.8 ip http secure-session timeout Description The ip http secure-session timeout command is used to configure the connection timeout of the HTTPS server. To restore to the default timeout time, please use no - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 70
in minutes. By default, the value is 10. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the timeout time of the HTTPS server connection as 15 minutes: T1500G-10MPS(config)# ip http secure - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 71
download to the switch. The length of the name ranges from 1 to 25 characters. The Key must be BASE64 encoded. ip-addr -- The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 72
from TFTP server with the IP address of fe80::1234 T1500G-10MPS(config)# ip http secure-server download key ssl-key ip-address fe80::1234 7.11 show ip http configuration Description The show ip http configuration command is used to display the configuration information of the HTTP server, including - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 73
Syntax show ip http secure-server Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of SSL: T1500G-10MPS(config)# show ip http secure-server 60 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 74
condition for the ARP Inspection to filter the packets. 8.1 ip source binding Description The ip source binding command is used to bind the IP address, MAC address, VLAN ID and the Port number together manually. You can manually bind the IP address, MAC address, VLAN ID and the Port number together - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 75
Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind an ACL entry with the IP 192.168.0.1, MAC 00:00:00:00:00:01, VLAN ID 2 and the Port number 5 manually. And then enable the entry for the ARP detection: T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 76
snooping function, in the format of 1-3, 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Snooping function on VLAN 1,4,6-7: T1500G-10MPS(config)#ip dhcp snooping vlan 1,4,6-7 63 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 77
1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information option 8.5 ip dhcp snooping information strategy Description The ip dhcp snooping information strategy command is used to select the operation for the Option 82 field of the DHCP request packets from the Host. To restore to the default - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 78
1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information strategy replace 8.6 ip dhcp snooping information remote-id Description The ip dhcp snooping information remote-id command is used to configure the customized sub-option Remote ID for the Option 82. To return to default Remote - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 79
users have access to these commands. Example Configure the customized sub-option Remote ID for the Option 82 as tplink on port 1/0/1: T1500G-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#ip dhcp snooping information remote-id tplink 8.7 ip dhcp snooping information circuit-id - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 80
users have access to these commands. Example Configure the Gigabit Ethernet port 1/0/2 to be a Trusted Port: T1500G-10MPS(config)#interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)#ip dhcp snooping trust 8.9 ip dhcp snooping mac-verify Description The ip dhcp snooping mac-verify command is used - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 81
1/0/2 T1500G-10MPS(config-if)#ip dhcp snooping mac-verify 8.10 ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets. The excessive DHCP packets will be discarded. To restore to the default configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 82
port 1/0/2 as 20 pps: T1500G-10MPS(config)#interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)#ip dhcp snooping limit rate 20 8.11 ip dhcp snooping decline rate Description The ip dhcp snooping decline rate command is used to enable the Decline Protect feature and configure the rate limit on - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 83
binding Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the IP-MAC-VID-PORT binding table: T1500G-10MPS(config)#show ip source binding 8.13 show ip dhcp snooping Description The show ip dhcp snooping command is used to display the running - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 84
Requirement None. Example Display the DHCP Snooping configuration of all Ethernet ports and LAGs: T1500G-10MPS#show ip dhcp snooping interface Display the DHCP Snooping configuration of Gigabit Ethernet port 1/0/5: T1500G-10MPS#show ip dhcp snooping interface gigabitEthernet 1/0/5 8.15 show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 85
. port-channel-id -- The ID of the port channel. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DHCP snooping option 82 configuration of all Ethernet ports and port channels: T1500G-10MPS#show ip dhcp snooping information interface 72 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 86
clear the Trusted Port list, please use no ip arp detection trust command .The specific ports, such as up-linked port and routing port and LAG port, should be set as Trusted Port. To ensure the normal communication of the switch, please configure the ARP Trusted Port before enabling the ARP Detect - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 87
access to these commands. Example Configure the Gigabit Ethernet ports 1/0/2-5 as the Trusted Port: T1500G-10MPS(config)#interface range gigabitEthernet 1/0/2-5 T1500G-10MPS(config-if-range)#ip arp inspection trust 9.3 ip arp inspection(interface) Description The ip arp inspection command is used - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 88
interface range gigabitEthernet 1/0/2-6 T1500G-10MPS(config-if-range)#ip arp inspection 9.4 ip arp inspection limit-rate Description The ip arp inspection limit-rate command is used to configure the ARP speed of a specified port. To restore to the default speed, please use no ip arp inspection limit - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 89
to the ARP transmit status: T1500G-10MPS(config)#interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)#ip arp inspection recover 9.6 show ip arp inspection Description The show ip arp inspection command is used to display the ARP detection global configuration including the enable/disable status - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 90
None. Example Display the configuration of Gigabit Ethernet port 1/0/1: T1500G-10MPS(config)#show ip arp inspection interface gigabitEthernet 1/0/1 Display the configuration of all Ethernet ports: T1500G-10MPS(config)#show ip arp inspection interface 9.8 show ip arp inspection statistics Description - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 91
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the number of the illegal ARP packets received: T1500G-10MPS(config)#show ip arp inspection statistics 9.9 clear ip arp inspection statistics Description The clear ip arp inspection statistics command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 92
command. Syntax ip dos-prevent no ip dos-prevent Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DoS defend function globally: T1500G-10MPS(config)#ip dos-prevent 10.2 ip dos-prevent type - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 93
syn-flood | win-nuke | smurf | ping-of-death } no ip dos-prevent type { land | scan-synfin | xma-scan | null- flood attack enabled, the switch will limit automatically the flood attack enabled, the switch will limit automatically the forwarding Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 94
of the detected DoS attack, including enable/disable status, the DoS Defend Type, the count of the attack, etc. Syntax show ip dos-prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the DoS information of the detected DoS attack globally - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 95
log information saved in the switch. It has two output T1500G-10MPS(config)#logging buffer 11.2 logging buffer level Description The logging buffer level command is used to configure the severity level and the status of the configuration input to the log buffer. To return to the default configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 96
the log with the same or smaller severity level value will be output. By default, it is 6 indicating that the log information with level 0-6 will be saved in the log buffer. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 97
Enable the log file flash function: T1500G-10MPS(config)#logging file flash 11.4 the flash, ranging from 1 to 48 hours. By default, the synchronization process takes place every 24 hours. immediate is not recommended. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 98
with the same or smaller severity level value will be saved to the flash. By default, it is 3 indicating that the log message marked with 0~3 will be saved in the log flash. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 99
Parameter idx -- The index of the log host. The switch supports 4 log hosts at most. host-ip -- The IP for the log host. level -- The severity level of By default, it is 6 indicating that the log information marked with 0~6 will be sent to the log host. Command Mode Global Configuration Mode - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 100
to these commands. Example Disable logging to the terminal devices: T1500G-10MPS(config)# no logging monitor 11.8 logging monitor level Description default, it is 5 indicating that all the log information between level 0-5 will be output to the terminal devices. Command Mode Global Configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 101
the information of the two channels, by default. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level T1500G-10MPS(config)# clear logging buffer 11.10 show logging local-config Description The show logging local-config command is used to display the configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 102
will be displayed, ranging from 1 to 4. Display the configuration of all the log hosts by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the log host 2: T1500G-10MPS(config)# show logging loghost 2 11.12 show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 103
Any Configuration Mode Privilege Requirement None. Example Display the log information from level 0 to level 5 in the log buffer: T1500G-10MPS( the log information in the log file by default. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 104
server command. Syntax ip ssh server no ip ssh server Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the SSH function: T1500G-10MPS(config)# ip ssh server 12.2 ip ssh version Description The - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 105
, Operator and Power User level users have access to these commands. Example Enable SSH v2: T1500G-10MPS(config)# ip ssh version v2 12.3 ip ssh algorithm Description The ip ssh algorithm command is used to configure the algorithm in SSH function. To disable the specified algorithm, please use no - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 106
time of SSH as 30 seconds: T1500G-10MPS(config)# ip ssh timeout 30 12.5 ip ssh max-client Description The ip ssh max-client command is used to specify the maximum number of the connections to the SSH server. To return to the default configuration, please use no ip ssh max-client command. Syntax - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 107
downloaded file must be in the range of 512 to 3072 bits. ip-addr -- The IP address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 108
users have access to these commands. Example Remove the SSH-1 type public key from the switch: T1500G-10MPS# remove public-key v1 12.8 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH. Syntax show ip ssh Command Mode Privileged EXEC Mode and Any - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 109
Example Display the global configuration of SSH: T1500G-10MPS(config)# show ip ssh 96 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 110
the supplicant. It is usually an 802.1X-supported network device, such as this TP-Link switch. It acts as an intermediary (proxy) between system-auth-control no dot1x system-auth-control Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 111
between the TP-Link 802.1x supplicant and the switch. Please disable the handshake feature if you are using a non-TP-Link 802.1x-compliant client software. This feature is enabled by default. Syntax dot1x handshake no dot1x handshake Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 112
information between the switch and the client. The EAP packets are terminated at the switch and repackaged in the Password Authentication Protocol (PAP have access to these commands. Example Configure the Authentication Method of IEEE 802.1X as "pap": T1500G-10MPS(config)#dot1x auth-method pap 13 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 113
Enable the enable the IEEE 802.1X accounting function globally: T1500G-10MPS(config)#dot1x accounting 13.5 dot1x guest-vlan(global) Description VLAN can access the specified network sources. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 114
quiet-period function and set the quiet-period as 5 seconds: T1500G-10MPS(config)#dot1x quiet-period 5 13.7 dot1x timeout Description The dot1x timeout command is used to configure the supplicant timeout. To restore to the default, please use no dot1x timeout supplicant-timeout command. Syntax dot1x - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 115
supplicant-timeout time --The maximum time for the switch to wait for the response from supplicant before resending a request to the supplicant., ranging from 1 to 9 in second. By default, it is 3 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 116
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the maximum transfer times of the repeated authentication request as 5: T1500G-10MPS(config)#dot1x max-reauth-req 5 13.9 dot1x Description The dot1x command is used to enable the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 117
Gigabit Ethernet port 1/0/2: T1500G-10MPS(config)#interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)#dot1x guest-vlan 13.11 dot1x port-control Description The dot1x port-control command is used to configure the Control Mode of IEEE 802.1X for the specified port. By default, the control mode is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 118
-10MPS(config)#interface gigabitEthernet 1/0/20 T1500G-10MPS(config-if)#dot1x port-control authorized-force 13.12 dot1x port-method Description The dot1x port-method command is used to configure the control type of IEEE 802.1X for the specified port. By default, the control type is "mac-based". To - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 119
Only Admin, Operator and Power User level users have access to these commands. Example Configure the Control Type for Gigabit Ethernet port 1/0/20 as "port-based": T1500G-10MPS(config)#interface gigabitEthernet 1/0/20 T1500G-10MPS(config-if)#dot1x port-method port-based 13.13 show dot1x global - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 120
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of 802.1X for Gigabit Ethernet port 1/0/2: T1500G-10MPS(config)#show dot1x interface gigabitEthernet 1/0/2 Display the configuration information of 802.1X for all Ethernet - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 121
manually, independent of the aging time. In the stable networks, the static MAC address entries can facilitate the switch of your desired entry. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and : T1500G-10MPS(config)# mac address-table static 00:02:58:4f - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 122
default. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the aging time as 500 seconds: T1500G can be added or removed manually, independent of the aging time. Syntax mac address-table filtering - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 123
to 4094. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator is 00:1e:4b:04:01:5d: T1500G-10MPS(config)# mac address-table filtering 00 table notification command is used to configure global settings of MAC address when the threshold of the switch's MAC address table is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 124
sending interval as 2 seconds: T1500G-10MPS(config)# mac address-table notification global-status enable table-full-status enable interval 2 14.5 mac address-table notification (interface) Description The mac address-table notification command is used to configure the MAC change notification on - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 125
T1500G-10MPS(config)# mac address-table notification global-status enable T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G configure the Port Security. To return to the default configurations, please use no mac address-table max-mac-count command. Port Security is to protect the switch - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 126
manually. The learned entries will be cleared after the switch switch is rebooted. status -- Select the action to be taken when the number of the MAC addresses reaches the maximum learning number on the port. By default Configuration T1500G-10MPS(config)# interface gigabitEthernet 1/0/1 T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 127
Admin, Operator and Power User level users have access to these commands. Example Configure the max learned MAC address number is VLAN 2 as 1000, and drop the packets that have no match in the MAC address table: T1500G-10MPS(config)# mac address-table security vid 2 max-learn 1000 drop 14.8 show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 128
static | filtering -- The type of your desired entry. By default all the entries are displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all address entries: T1500G-10MPS(config)# show mac address-table 14.9 clear mac - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 129
of the MAC address. Syntax show mac address-table aging-time Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the Aging Time of the MAC address: T1500G-10MPS(config)# show mac address-table aging-time 14.11 show mac address-table max-mac-count - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 130
port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the address configuration of port 1/0/1: T1500G-10MPS(config)# show mac address-table interface gigabitEthernet 1/0/1 14.13 show mac address-table count - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 131
Specify the VLAN which the entry belongs to. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of the MAC address 00:00:00:00:23:00 in VLAN 1: T1500G-10MPS(config)#show mac address-table address 00:00:00:00:23:00 vid 1 118 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 132
vlan vid Parameter vid --The specified VLAN id. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MAC address configuration of vlan 1: T1500G-10MPS(config)# show mac address-table vlan 1 14.16 show mac address-table notification Description - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 133
mac address-table security [ vid vid ] Parameter vid --The specified VLAN id. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the MAC address security configuration of vlan 1: T1500G-10MPS(config)# show mac address-table security vid 1 120 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 134
can be used to configure the System information and System IP, reboot and reset the switch, upgrade the switch system and other operations. 15.1 system-time manual Description The system-time manual command is used to configure the system time manually. Syntax system-time manual time Parameter time - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 135
Solomon Is., New Caledonia, Vladivostok. UTC+12:00 -- TimeZone for Fiji, Magadan, Auckland, Welington. UTC+13:00 -- TimeZone for Nuku'alofa, Samoa. ntp-server -- The IP address for the Primary NTP Server. 122 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 136
Configure the system time mode as NTP, the time zone is UTC-12:00, the primary NTP server is 133.100.9.2 and the secondary NTP server is 139.78.100.163, the fetching-rate is 11 hours: T1500G , Australia, Europe and New-Zealand respectively. The default value is Europe. Following are the time ranges - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 137
the daylight saving time as USA standard: T1500G-10MPS(config)#system-time dst predefined USA 15.4 system-time dst date Description The system-time dst date command is used to configure the one-off daylight saving time. The start date is in the current year by default. The time range of the daylight - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 138
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the daylight saving time from zero clock, Apr 1st to zero clock Oct 1st and the offset is 30 minutes in 2015: T1500G-10MPS(config)# system-time dst date Apr 1 00:00 2015 Oct 1 00:00 2015 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 139
no hostname Parameter hostname -- System Name. The length of the name ranges from 1 to 32 characters. By default, it is the device name, for example "T1500G-10MPS". Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 140
Example Configure the system location as SHENZHEN: T1500G-10MPS(config)# location SHENZHEN 15.8 contact-info Description The contact-info command is used to configure the system . It consists of 32 characters at most. It is "www.tp-link.com" by default. Command Mode Global Configuration Mode 127 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 141
the system contact information as www.tp-link.com: T1500G-10MPS(config)# contact-info www.tp-link.com 15.9 ip address Description This ip address command is used to configure the IP address, IP subnet mask and default fateway for the specified interface manually. The interface type includes: routed - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 142
address from the DHCP Server. bootp -- Specify the Layer 3 interface to obtain IP address from the BOOTP Server. Command Mode Interface Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the DHCP Client function on - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 143
, all configuration of the switch will restore to the factory defaults and your current settings will be lost. Syntax reset Command Mode Privileged EXEC Mode Privilege Requirement Only Admin level users have access to these commands. Example Reset the software of the switch: T1500G-10MPS# reset 15 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 144
startup-config tftp command is used to backup the configuration file to TFTP server. Syntax copy startup-config tftp ip-address ip-addr filename name Parameter ip-addr -- IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. name -- Specify - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 145
startup-config command is used to download the configuration file to the switch from TFTP server. Syntax copy tftp startup-config ip-address ip-addr filename name Parameter ip-addr -- IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 146
no boot application Parameter image1 | image2 -- Specify the image file to be configured. By default, the image1.bin is the startup image and the image2.bin is the backup access to these commands. Example Configure the image2.bin as the startup image: T1500G-10MPS(config)# boot application filename - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 147
the Backup Image, and user can chose whether to reboot the switch will the Backup Image. Syntax firmware upgrade ip-address ip-addr filename name Parameter ip-addr -- IP Address of the TFTP server. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.1 or fe80::1234. name -- Specify the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 148
T1500G-10MPS# firmware upgrade ip-address fe80::1234 filename firmware.bin It will only upgrade the backup image. Continue? (Y/N):y Operation OK! Reboot with the backup image? (Y/N): n 15.19 ping Description The ping command is used to test the connectivity between the switch and one node of the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 149
commands. Example Test the connectivity between the switch and the network device with the IP 192.168.0.131. If the destination device has not been found after 20 maxHops, the connection between the switch and the destination device is failed to establish: T1500G-10MPS# tracert 192.168.0.131 20 136 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 150
, Device Location, System Contact, Hardware Version, Firmware Version, System Time, Run Time and so on. Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the system information: T1500G-10MPS# show system-info 15.22 show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 151
commands. Example Display the system current operating configuration: T1500G-10MPS# show running-config 15.24 show startup-config Description The show startup-config command is used to display the current configuration saved in the switch. These configuration settings will not be lost the next time - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 152
system-time command is used to display the time information of the switch. Syntax show system-time Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the time information of the switch T1500G-10MPS# show system-time 15.26 show system-time dst - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 153
and Any Configuration Mode Privilege Requirement None. Example Display the NTP mode configuration information of the switch: T1500G-10MPS# check the connection status of the cable connected to the switch, locate and diagnose the trouble spot of the network. Syntax show cable-diagnostics interface - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 154
5 seconds/1minute/5minutes. Syntax show cpu-utilization Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the CPU utilization information of the switch: T1500G-10MPS# show cpu-utilization 15.30 show memory-utilization Description The show memory - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 155
142 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 156
and Power User level users have access to these commands. Example To enter the Interface gigabitEthernet Configuration Mode and configure port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 16.2 interface range gigabitEthernet Description The interface range gigabitEthernet command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 157
an error on one port. Example To enter the Interface range gigabitEthernet Configuration Mode, and configure ports 1, 2, 3, 6, 7 and 9 at the same time by adding them to one port-list: T1500G-10MPS(config)# interface range gigabitEthernet 1/0/1-3,1/0/6-7,1/0/9 16.3 description Description The - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 158
interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)# description Port_5 16.4 shutdown Description The shutdown command is used to disable an Ethernet port. To enable this port again, please use no shutdown command. Syntax shutdown no shutdown Command Mode Interface Configuration Mode (interface - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 159
flow-control function for port 1/0/3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# flow-control 16.6 duplex Description The duplex command is used to configure the Duplex Mode for an Ethernet port. To return to the default configuration, please use no duplex command - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 160
jumbo frame which is allowed to pass through the switch as 1600 bytes: T1500G-10MPS(config)# jumbo-size 1600 16.8 speed Description The speed command is used to configure the Speed Mode for an Ethernet port. To return to the default configuration, please use no speed command. Syntax speed { 10 | 100 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 161
Privilege Requirement Only Admin and Operator level users have access to these commands. Example Configure the Speed Mode as 100Mbps for port 1/0/3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/3 T1500G-10MPS(config-if)# speed 100 16.9 storm-control Description The storm-control command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 162
Admin, Operator and Power User level users have access to these commands. Example Configure the ingress-rate as 5120Kbps and egress-rate as 1024Kbps for port 1/0/5: T1500G-10MPS(config)# interface gigabitEthernet 1/0/5 T1500G-10MPS(config-if)# bandwidth ingress 5120 egress 1024 16.11 clear counters - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 163
port -- The Ethernet port number. lagid -- The ID of the LAG.. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the connection status of all ports and LAGs: T1500G-10MPS(config)# show interface status Display the connection status of port - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 164
counters Display the statistics information of port 1/0/2: T1500G-10MPS(config)# show interface counters gigabitEthernet 1/0/2 16.14 show interface configuration Description The show interface configuration command is used to display the configurations of all ports and LAGs, including Port-status - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 165
Privilege Requirement None. Example Display the configurations of all Ethernet ports and LAGs: T1500G-10MPS(config)# show interface configuration Display the configurations of port 1/0/2: T1500G-10MPS(config)# show interface configuration gigabitEthernet 1/0/2 16.15 show storm-control Description - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 166
port-list --The list of Ethernet ports. lagid-list -- The list of LAGs. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the bandwidth-limit information of port 1/0/4: T1500G-10MPS(config)# show bandwidth interface gigabitEthernet 1/0/4 153 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 167
service experience of a better quality. 17.1 qos Description The qos command is used to configure the priority level of packets from the port. To return to the default configuration Example Configure the priority of port 1/0/5 as TC3: T1500G-10MPS(config)# interface gigabitEthernet 1/0/5 T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 168
Command Mode Global Configuration Mode Privilege mapping relation between IEEE 802.1P Priority and egress queue: T1500G-10MPS (config)# qos cos 17.3 qos dscp Description The . Syntax qos dscp no qos dscp Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 169
and CoS value: T1500G-10MPS(config)# qos dscp 17.4 qos queue cos-map Description The qos queue cos-map command is used to configure the mapping relation tag, CoS value and the TC egress queue. To return to the default configuration, please use no qos queue cos-map command. When 802.1P Priority - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 170
T1500G-10MPS(config)# qos queue cos-map 5 2 17.5 qos queue dscp-map Description The qos queue dscp-map command is used to configure the mapping relation between DSCP Priority and the TC queue. To return to the default configuration is enabled; the untagged non-IP datagram are mapped based on port - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 171
is used to configure the Schedule Mode. To return to the default Equal-Mode, please use no qos queue mode command. When the network is congested, the program that many packets complete for resources must be solved, usually in the way of queue scheduling. The switch will control the forwarding - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 172
. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of QoS for all ports and LAGs: T1500G-10MPS# show qos interface Display the configuration of QoS for ports 1/0/1-4: T1500G-10MPS# show qos interface gigabitEthernet 1/0/1-4 17 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 173
of DSCP Priority. Syntax show qos dscp-map Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of DSCP Priority: T1500G-10MPS# show qos dscp-map 17.10 show qos queue mode Description The show qos queue mode command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 174
is used to display the status of IEEE 802.1P priority and DSCP priority. Syntax show qos status Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the status of IEEE 802.1P priority and DSCP priority: T1500G-10MPS# show qos status 161 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 175
troubleshooting the network. 18.1 monitor session destination interface Description The monitor session destination interface command is used to configure 1. port -- The monitoring port number. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 176
session 1 destination interface gigabitEthernet 1/0/2 Delete the monitor session 1: T1500G-10MPS(config)# no monitor session 1 18.2 monitor session source interface Description The monitor session source interface command is used to configure the monitored port/ LAG. To delete the corresponding - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 177
not is not demanded strictly. 4. The monitoring port cannot be link-aggregation member. Example Create monitor session 1, then configure port 4, 5, 7 as monitored port and enable ingress monitoring: T1500G-10MPS(config)# monitor session 1 source interface gigabitEthernet 1/0/4-5,1/0/7 rx Delete port - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 178
command is used to configure the forward port/LAG T1500G-10MPS(config-if)# port isolation gi-forward-list 1/0/1-2,1/0/4 po-forward-list 2 Set all Ethernet ports and LAGs to forward list of port 1/0/2, namely restore to the default setting: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 179
its forward port list, ranging from 1 to 6. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the forward-list of port 1/0/2: T1500G-10MPS# show port isolation interface gigabitEthernet 1/0/2 Display the forward-list of all Ethernet ports and - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 180
switch will display an alert or further block the corresponding port according to the configuration detection Command Mode Global Configuration Mode Privilege Requirement Only loopback detection function globally: T1500G-10MPS(config)# loopback-detection detection packets from switch ports to network - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 181
T1500G-10MPS(config)# loopback-detection interval 50 20.3 loopback-detection recovery-time Description The loopback-detection recovery-time command is used to configure ranging from 1 to 100 and the default value is 3. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 182
-detection config command is used to configure the process-mode and recovery-mode for the ports/LAGs by which the switch copes with the detected loops. Syntax loopback-detection config [ process-mode { alert | port-based }] [ recovery-mode { auto | manual }] Parameter process-mode -- The mode how - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 183
and Power User level users have access to these commands. Example Configure the loopback detection process-mode as port-based and recovery-mode as manual for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# loopback-detection config process-mode port-based - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 184
Syntax show loopback-detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of loopback detection function: T1500G-10MPS# show loopback-detection global 20.8 show loopback-detection interface Description The - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 185
Example Display the configuration of loopback detection function and the status of all ports and LAGs: T1500G-10MPS# show loopback-detection interface Display the configuration of loopback detection function and the status of port 1/0/5: T1500G-10MPS# show loopback-detection interface - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 186
ranges is 500-1499 and the Extend-IP ACL is 1500-2499. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Create a standard-IP ACL whose ID is 523: T1500G-10MPS(config)# access-list create 523 21.2 mac - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 187
acl-id -- The desired Standard-IP ACL for configuration. rule-id -- The rule ID. deny -- The operation to discard packets. permit --The operation to forward packets. It is the default value. source-ip -- The source IP address contained in the rule. source-ip-mask -- The source IP address mask. It is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 188
acl-id--The desired Extended-IP ACL for configuration. rule-id -- The rule ID. deny -- The operation to discard packets. permit --The operation to forward packets. It is the default value. source-ip -- The source IP address contained in the rule. source-ip-mask -- The source IP address mask. It is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 189
switch: T1500G-10MPS(config)# access-list create 2220 T1500G-10MPS(config)# access-list extended 2220 rule 10 permit sip 192.168.0.100 smask 255.255.255.0 21.5 rule Description The rule command is used to configure operation to forward packets. It is the default value. source-mac -- The source MAC - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 190
packets match this rule will be forwarded by the switch: T1500G-10MPS(config)# mac access-list 20 T1500G-10MPS(config-mac-acl)# rule 10 permit smac 00 Name, ranging from 1 to 16 characters. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 191
of the ACL to which the above policy is applied. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access commands. Example Add ACL whose ID is 120 for policy1: T1500G-10MPS(config)# access-list policy action policy1 120 21.8 access- - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 192
Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind ACL 100 to VLAN 2: T1500G-10MPS(config)# interface vlan 2 T1500G-10MPS(config-if)# access-list bind acl 100 21.10 access-list bind(interface) Description The access-list bind command is - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 193
of the policy desired to bind. Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface commands. Example Bind policy1 to port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# access-list bind policy1 21 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 194
acl-id -- The ID of the ACL selected to display the configuration. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of the MAC ACL whose ID is 20: T1500G-10MPS(config)# show access-list 20 21.13 show access-list policy - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 195
show access-list bind command is used to display the configuration of Policy bind. Syntax show access-list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of Policy bind: T1500G-10MPS(config)# show access-list bind 182 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 196
max power the PoE switch can supply. It ranges from 1 to 116W. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max power the PoE switch can supply as 100W: T1500G-10MPS(config)# power - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 197
-limit" indicates you can manually enter a value. It ranges from 1 to 300. The value is in the unit of 0.1 watt. For instance, if you want to configure the max power as 5w, you should enter 50. "auto" indicates the value is assigned automatically by the PoE switch. "class1" represents 4w. "class2 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 198
T1500G-10MPS(config)# power profile "IP Camera" supply enable priority low consumption 50 22.3 power time-range Description The power time-range command is used to create PoE time-range for the switch and enter Power Time-range Configuration Mode. After a PoE time-range is created, you need to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 199
union is the Absolute Time-range. If no absolute time range is configured, the absolute time range takes effect from January 1, 2000 00:00 PoE of the switch and specify the date extending from 08:00 on May 5th, 2012 to 22:00 on Oct. 5th, 2012: T1500G-10MPS(config)# power time-range tRange1 T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 200
from Monday to Sunday. To delete the corresponding periodic mode time-range configuration, please use no periodic command. Syntax periodic start start-time end 00 to 16:00 during the weekends: T1500G-10MPS(config)# power time-range tRange2 T1500G-10MPS(config-time-range)# periodic start 08:00 end - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 201
T1500G-10MPS(config-time-range)# periodic start 10:00 end 16:00 day-of-the-week 6-7 22.6 power holiday Description The power holiday command is used to create PoE holiday for the switch. To delete the corresponding PoE holiday configuration, please use no power holiday command. Syntax power holiday - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 202
access to these commands. Example Create a holiday mode time-range for the PoE time-range named "tRange3" and configure PoE time-range of the switch excludes the PoE holiday: T1500G-10MPS(config)# power time-range tRange3 T1500G-10MPS(config-time-range)# holiday exclude 22.8 power inline consumption - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 203
PD linked to the port with lower priority will be disconnected. By default, the priority level is "low". Command Mode Interface Configuration Mode these commands. Example Configure the PoE priority as "low" for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 204
. By default, the PoE status is "enable". Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Enable the PoE feature for port 1/0/2: T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 205
Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Bind the PoE profile named "IP Camera" to port 1/0/2: T1500G-10MPS(config)# interface - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 206
Privilege Requirement None. Example Display the PoE information of the system: T1500G-10MPS# show power inline 22.14 show power inline configuration interface Description The show power inline configuration interface command is used to display the PoE configuration of the certain port. Syntax show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 207
port ] Parameter port -- The Ethernet port number. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the PoE information of all ports: T1500G-10MPS# show power inline information interface 22.16 show power profile Description The show power - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 208
-range name, ranging from 1 to 16 characters. All PoE time-range configurations will be displayed if not specified. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration of PoE time-range: T1500G-10MPS# show power time-range 195 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 209
Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant links and backup links as well as optimize paths. 23.1 debug spanning-tree Description The debug spanning-tree command is used to enable debuggning of spanning-tree - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 210
command. Syntax spanning-tree no spanning-tree Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level have access to these commands. Example Enable the STP function: T1500G-10MPS(config)# spanning-tree 23.3 spanning-tree(interface) Description The - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 211
CIST and the common parameters of all instances. To return to the default configuration, please use no spanning-tree common-config command. CIST (Common and Internal Spanning Tree) is the spanning tree in a switched network, connecting all devices in the network. Syntax spanning-tree common-config - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 212
1/0/1 T1500G-10MPS(config-if)# spanning-tree common-config port-priority 64 ext-cost 100 int-cost 100 portfast enable point-to-point open 23.5 spanning-tree mode Description The spanning-tree mode command is used to configure the STP mode of the switch. To return to the default configurations - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 213
, the default value. rstp --Rapid Spanning Tree Protocol mstp --Multiple Spanning Tree Protocol Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the spanning-tree mode as mstp: T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 214
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Map the VLANs 1-100 to Instance 1: T1500G-10MPS(config)# spanning-tree mst configuration T1500G-10MPS(config-mst)# instance 1 vlan 1-100 Disable Instance 1, namely remove all the mapping VLANs 1-100 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 215
Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the region name of MST as "region1": T1500G-10MPS(config)# spanning-tree mst configuration T1500G-10MPS(config-mst)# name region1 23.9 revision Description The revision command is used to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 216
must be multiple of 4096 ranging from 0 to 61440. By default, it is 32768. MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 217
-10MPS(config)# interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)# spanning-tree mst instance 1 port-priority 64 cost 2000 23.12 spanning-tree priority Description The spanning-tree priority command is used to configure the bridge priority. To return to the default value of bridge priority - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 218
(Hello Time + 1) - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 219
, ranging from 1 to 20 in pps. By default, it is 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the hold-count of STP as 8pps: T1500G-10MPS(config)# spanning-tree hold-count 8 23.15 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 220
discarded, ranging from 1 to 40 in hop. By default, it is 20. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the max-hops of STP as 30: T1500G-10MPS(config)# spanning-tree max-hops 30 23.16 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 221
Configuration T1500G-10MPS(config-if)# spanning-tree bpduguard 23.18 spanning-tree guard loop Description The spanning-tree guard loop command is used to enable the Loop Protect function for a port. Loop Protect is to prevent the loops in the network brought by recalculating STP because of link - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 222
Enable the Loop Protect function for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# spanning-tree guard loop root no spanning-tree guard root Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet / interface - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 223
switch, the switch will be busy with removing MAC address entries, which may decrease the performance and stability of the network. With the Protect of Spanning Tree function enabled, you can configure Tree for port 1/0/2: T1500G-10MPS(config)# interface gigabitEthernet 1/0/2 T1500G-10MPS(config-if)# - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 224
of spanning-tree. Syntax show spanning-tree active Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the active information of spanning-tree: T1500G-10MPS(config)# show spanning-tree active 23.23 show spanning-tree bridge Description The show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 225
The Ethernet port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the spanning-tree information of all ports: T1500G-10MPS(config)# show spanning-tree interface Display the spanning-tree information of port - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 226
-- The Ethernet port number. lagid -- The ID of the LAG. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the protect information of all ports: T1500G-10MPS(config)# show spanning-tree interface-security Display the protect information of port - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 227
None. Example Display the region information and mapping information of VLAN and MST Instance: T1500G-10MPS(config)#show spanning-tree mst configuration Display the related information of MST Instance 1: T1500G-10MPS(config)#show spanning-tree mst instance 1 Display all the ports information of MST - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 228
Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups being broadcasted in the network. 24.1 ip igmp snooping(global) Description The ip igmp snooping command is used to configure IGMP Snooping globally. To disable the IGMP Snooping - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 229
600. The default aging time is 300 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify IGMP Snooping router port aging time as 100 seconds globally: T1500G-10MPS(config)# ip igmp snooping - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 230
600. The default aging time is 260 seconds. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify IGMP Snooping member port aging time as 100 seconds globally: T1500G-10MPS(config)# ip igmp snooping - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 231
to these commands. Example Enable the IGMP report suppression function: T1500G-10MPS(config)# ip igmp snooping report-suppression 24.6 ip igmp snooping immediate-leave Description The ip igmp snooping immediate-leave command is used to configure the Fast Leave function for port. To disable the Fast - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 232
, ranging from 1 to 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the interval of Specific Query Message to 3 seconds: T1500G-10MPS(config)# ip igmp snooping last-listener query-inteval - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 233
sent, ranging from 1 to 5. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Specify the number of Specific Query Message to 3: T1500G-10MPS(config)# ip igmp snooping last-listener query-count 3 24.10 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 234
Time ranges from 60 to 600 in seconds. By default, it is 0 and the global member-time will be used. port-list -- The list of Ethernet ports. lagid -- The ID of the LAGs. ip -- The static multicast IP address. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 235
ip igmp snooping vlan-config vlan-id-list router-ports-forbidden interface [ gigabitEthernet port-list | port-channel port-channel-id ] Parameter vlan-id-list -- The ID list of the VLAN desired to modify configuration ports in VLAN 1 : T1500G-10MPS(config)# ip igmp snooping vlan-config 1 router-ports - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 236
specified, the default multicast VLAN will be selected. router-time -- Router Port Time. Within this time, if the switch does not receive default, it is 0 and the global member-time will be used. port-list -- The list of Ethernet ports. lagid -- The ID of the LAGs. Command Mode Global Configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 237
T1500G-10MPS(config)# ip igmp snooping multi-vlan-config 3 mtime 100 T1500G-10MPS(config)# ip igmp snooping multi-vlan-config 3 rport interface gigabitEthernet 1/0/3 24.13 ip port-channels will be discarded. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 238
ip -- Specify the IP address. The switch will use this IP address to replace the source IP address of the IGMP packets. Command Mode Global Configuration T1500G-10MPS(config)# ip igmp snooping multi-vlan-config 2 replace-sourceip 192.168.0.112 24.15 ip igmp snooping querier vlan Description The ip - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 239
T1500G-10MPS(config)#ip igmp snooping querier vlan 1 24.16 ip igmp snooping querier vlan (general query) Description The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a general query frame. To return to the default configuration, please - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 240
-time as 20 seconds: T1500G-10MPS(config)#ip igmp snooping querier vlan 2 query-interval 200 T1500G-10MPS(config)#ip igmp snooping querier vlan 2 max-response-time 20 24.17 ip igmp snooping max-groups Description The ip igmp snooping max-groups command is used to configure the maximum number of - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 241
of groups that ports 1/0/2-5 can join as 10, and configure the throttling action as replace: T1500G-10MPS(config)#interface range gigabitEthernet 1/0/2-5 T1500G-10MPS(config-if-range)#ip igmp snooping max-groups 10 T1500G-10MPS(config-if-range)#ip igmp snooping max-groups action replace 24.18 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 242
Mode Privilege Requirement Only Admin, Operator and Power User level users have access to these commands. Example Configure the filtering mode of profile 1 as deny: T1500G-10MPS(config)# ip igmp profile 1 T1500G-10MPS(config-igmp-profile)#deny 24.20 permit Description The permit command is used to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 243
access to these commands. Example Configure one of the filter multicast address entry as range 225.1.1.1 to 226.3.2.1 in profile 1: T1500G-10MPS(config)# ip igmp profile 1 T1500G-10MPS(config-igmp-profile)#range 225.1.1.1 226.3.2.1 24.22 ip igmp filter Description The ip igmp filter command is used - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 244
1/0/2 T1500G-10MPS(config-if)# ip igmp filter 1 24.23 clear ip igmp snooping statistics Description The clear ip igmp snooping statistics command is used to clear the statistics of the IGMP packets. Syntax clear ip igmp snooping statistics Command Mode Privileged EXEC Mode and Any Configuration Mode - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 245
snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the global configuration of IGMP: T1500G-10MPS# show ip igmp snooping 24.25 show ip igmp snooping interface Description The show ip igmp snooping interface command is used to display - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 246
Example Display the IGMP baisic configuration configuration of all ports and LAGs: T1500G-10MPS# show ip igmp snooping interface basic-config Display the IGMP basic configuration of port 1/0/2: T1500G-10MPS# show ip igmp snooping interface gigabitEthernet 1/0/2 basic-config Display the IGMP packet - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 247
-vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the Multicast VLAN configuration: T1500G-10MPS# show ip igmp snooping multi-vlan 24.28 show ip igmp snooping groups vlan Description The show ip igmp snooping groups vlan command is used to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 248
Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the information of all IGMP snooping groups: T1500G-10MPS#show ip igmp snooping groups Display all the multicast entries in VLAN 5: T1500G-10MPS(config)#show ip igmp snooping groups vlan 5 Display the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 249
Mode Privilege Requirement None. Example Display all Querier information: T1500G-10MPS(config)# show ip igmp snooping querier 24.31 show ip igmp profile Description The show ip igmp profile command is used to display the configuration information of all the profiles or a specific profile. Syntax - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 250
Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement None. Example Display the configuration information of all profiles: T1500G-10MPS(config)# show ip igmp profile 237 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 251
. To return to the default configuration, please use no snmp-server command. Syntax snmp-server no snmp-server Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable the SNMP function: T1500G-10MPS(config)# snmp-server - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 252
Only Admin level users have access to these commands. Example Add a View named view1, configuring the OID as 1.3.6.1.6.3.20, and this OID can be managed by the SNMP management station: T1500G-10MPS(config)# snmp-server view view1 1.3.6.1.6.3.20 include 25.3 snmp-server group Description The snmp - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 253
and encryption）. By default, the Security Level is noAuthNoPriv. There is no need to configure this in SNMP v1 view generated by the switch's SNMP agent. Command Mode Global Configuration Mode Privilege Requirement Only Admin be received by Management station: T1500G-10MPS(config)# snmp-server group - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 254
The User in an SNMP Group can manage the switch via the management station software. The User and its default, the Authentication Mode is "none". confirm-pwd -- Authentication Password, ranging from 1 to 16 characters. The question marks and spaces are not allowed. This password in the configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 255
and DES indicates DES encryption method is used. By default, the Privacy Mode is "none". encrypt-pwd -- Privacy Password, ranging from 1 to 16 characters. The question marks and spaces are not allowed. This password in the configuration file will be displayed in the symmetric encrypted form. Command - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 256
authNoPriv | authPriv }] [ type { trap | inform }] [ retries retries ] [ timeout timeout ] no snmp-server host ip user-name Parameter ip -- The IP Address of the management Host. Both IPv4 and IPv6 addresses are supported, for example 192.168.0.100 or fe80::1234. udp-port -- UDP port, which is used - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 257
as inform, the maximum time for the switch to wait as 1000 seconds, and the retries time as 100: T1500G-10MPS(config)# snmp-server host 192.168.0.146 162 admin smode v2c type inform retries 100 timeout 1000 Add a Notification entry, and configure the IP Address of the management Host as fe80::1234 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 258
25.7 snmp-server engineID Description The snmp-server engineID command is used to configure the local and remote engineID of the switch. To restore to the default setting, please use no snmp-server engineID command. Syntax snmp-server engineID { [ local local-engineID ] [ remote remote-engineID ] } - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 259
a received SNMP request fails the authentication. By default, it is enabled. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP standard linkup trap for the switch: T1500G-10MPS(config)# snmp-server traps snmp linkup - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 260
is sent when CPU usage exceeds the predefined threshold. By default, the CPU usage threshold of the switch is 80%. flash -- Enable flash trap. It is sent when flash is modified during operations such as backup, reset, firmware upgrade, configuration import, etc. lldp -- Enable lldp trap. It is sent - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 261
It is sent when memory usage exceeds 80%. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Enable SNMP extended bandwidth-control trap for the switch: T1500G-10MPS(config)# snmp-server traps bandwidth-control 25.11 snmp-server - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 262
Enable VLAN-created trap only for the switch: T1500G-10MPS(config)# snmp-server traps vlan create 25.12 rmon history Description The rmon history command is used to configure the history sample entry. To return to the default configuration, please use no rmon history command. RMON (Remote Monitoring - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 263
T1500G-10MPS(config)# rmon history 1-3 interface gigabitEthernet 1/0/2 interval 100 owner owner1 25.13 rmon event Description The rmon event command is used to configure the entries of SNMP-RMON Event. To return to the default configuration, please use no rmon event command. Event Group, as one of - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 264
T1500G-10MPS(config)# rmon event 1-4 user user1 description description1 type log owner owner1 25.14 rmon alarm Description The rmon alarm command is used to configure SNMP-RMON Alarm Management. To return to the default configuration, please use no rmon alarm command. Alarm Group is one of the - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 265
By default, it is 1800. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure rmon alarm entries 1-3 binding with statistics entry 2, the owners as owner1 and the alarm intervals as 100 seconds: T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 266
name -- The creator of the event entry, ranging from 1 to 16 characters. By default, it is "monitor". status -- The status of the statistics entry, either "underCreation Example Configure the statistics entries 1-3 with the statistics port as 1/0/1, owner as owner1 and status as valid: T1500G-10MPS( - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 267
the View table. Syntax show snmp-server view Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the View table: T1500G-10MPS# show snmp-server view 25.18 show snmp-server group Description The show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 268
User table. Syntax show snmp-server user Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the User table: T1500G-10MPS# show snmp-server user 25.20 show snmp-server community Description The show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 269
the SNMP. Syntax show snmp-server engineID Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the engineID: T1500G-10MPS# show snmp-server engineID 25.23 show rmon history Description The show rmon - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 270
Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of all history sample entries: T1500G default, the configuration of all SNMP-RMON enabled entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 271
default, the configuration of all Alarm Management entries is displayed. Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the Alarm Management entry 1-2: T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 272
Privilege Requirement Only Admin level users have access to these commands. Example Display the configuration of the statistics entry 1: T1500G-10MPS#show rmon statistics 1 259 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 273
function globally: T1500G-10MPS(config)#lldp 26.2 lldp hold-multiplier Description The lldp hold-multiplier command is used to configure the Hold Hold Multiplier * Transmit Interval. To return to the default configuration, please use no lldp hold-multiplier command. Syntax lldp hold-multiplier - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 274
to these commands. Example Specify Hold Multiplier as 5: T1500G-10MPS(config)#lldp hold-multiplier 5 26.3 lldp timer Description The lldp timer command is used to configure the parameters about transmission. To return to the default configuration, please use no lldp timer command. Syntax lldp timer - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 275
The value ranges from 1 to 10 and the default value is 3. Command Mode Global Configuration Mode Privilege Requirement Only Admin, Operator and Power User and Trap message to NMS as 120 seconds: T1500G-10MPS(config)#lldp timer tx-interval 45 T1500G-10MPS(config)#lldp timer notify-interval 120 26.4 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 276
Syntax lldp transmit no lldp transmit Command Mode Interface Configuration Mode (interface gigabitEthernet / interface range gigabitEthernet) Gigabit Ethernet port 1/0/1 to transmit LLDPDU: T1500G-10MPS(config)# interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#lldp transmit 26.6 lldp - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 277
-10MPS(config)#interface gigabitEthernet 1/0/1 T1500G-10MPS(config-if)#lldp snmp-trap 26.7 lldp tlv-select Description The lldp tlv-select command is used to configure TLVs to be included in outgoing LLDPDU. To exclude TLVs, please use no lldp tlv-select command. By default, All TLVs are included in - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 278
Fast Start Count parameter. It ranges from 1 to 10. By default, it is 4. Command Mode Global Configuration Mode Privilege Requirement Only Admin and Operator level users have access to these commands. Example Specify Fast Start Count as 5: T1500G-10MPS(config)# lldp med-fast-count 5 26.9 lldp med - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 279
1/0/2 T1500G-10MPS(config-if)# lldp med-status 26.10 lldp med-tlv-select Description The lldp med-tlv-select command is used to configure LLDP-MED TLVs to be included in outgoing LLDPDU for the corresponding port. To exclude LLDP-MED TLVs, please use no lldp med-tlv-select command. By default, All - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 280
T1500G-10MPS(config-if)# no lldp med-tlv-select network-policy inventory- management 26.11 lldp med-location Description The lldp med-location command is used to configure { dhcp-server | endpoint | switch } ] ] } Parameter emergency-number -- Emergency Call Service ELIN identifier, which is used - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 281
Requirement None. Example Display the global configuration of LLDP: T1500G-10MPS#show lldp 26.13 show lldp interface Description The show lldp interface command is used to display LLDP configuration of the corresponding port. By default, the LLDP configuration of all the ports will be displayed - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 282
is used to display the LLDP information of the corresponding port. By default, the LLDP information of all the ports will be displayed. Syntax show Mode and Any Configuration Mode Privilege Requirement None. Example Display the LLDP information of Gigabit Ethernet port 1/0/1: T1500G-10MPS#show lldp - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 283
between the local device and neighbor device of the corresponding port. By default, the LLDP statistic information of all the ports will be displayed. Any Configuration Mode Privilege Requirement None. Example Display the LLDP statistic information of Gigabit Ethernet port 1/0/1: T1500G-10MPS#show - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 284
switch supports Login List for users to gain access to the switch, and Enable List for normal users to gain administrative privileges. RADIUS/TACACS+ Server User can configure is disabled by default. Syntax aaa enable no aaa enable Command Mode Global Configuration Mode Privilege Requirement - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 285
characters By default, it is empty. 7 -- Indicates a symmetric encrypted password with fixed length will follow. encrypted-password -- A symmetric encrypted password with fixed length, which you can copy from another switch's configuration file. After the encrypted password is configured, you - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 286
default, it is empty. The password in the configuration file will be displayed in the MD5 encrypted form. 5 -- Indicates an MD5 encrypted password with fixed length will follow. encrypted-password -- An MD5 encrypted password with fixed length, which you can copy from another switch's configuration - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 287
logged-in user to gain administrator level privileges. The password will be displayed in the encrypted form: T1500G-10MPS (config)#enable admin secret 0 123 27.4 tacacas-server host Description The tacacs-server host command is used to configure a new TACACS+ server. To delete the specified TACACS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 288
switch's configuration file. The key or encrypted-key you configured here will be displayed in the encrypted form. Always configure the default. Example Configure a TACACS+ server with the IP address as 1.1.1.1, TCP port as 1500, timeout as 6 seconds, and the unencrypted key string as 12345. T1500G - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 289
T1500G-10MPS(config)# show tacacs-server 27.6 radius-server host Description The radius-server host command is used to configure a new RADIUS server. To delete the specified RADIUS server, please use no radius-server host command. Syntax radius-server host ip-address [ auth-port port-id ] [ acct- - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 290
are added in the server group "radius" by default. Example Configure a RADIUS server with the IP address as 1.1.1.1, authentication port as 1200, timeout as 6 seconds, retransmit times as 3, and the unencrypted key string as 12345. T1500G-10MPS(config)# radius-server host 1.1.1.1 auth-port 1200 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 291
servers for authentication. This command puts the switch in the server group subconfiguration mode. To the server group name. Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have server group with the name radius1: T1500G-10MPS(config)# aaa group radius radius1 - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 292
no server ip-address Parameter ip-address -- Specify the server's IP address. Command Mode Server Group Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Create the RADIUS server 1.1.1.1 to RADIUS server group "radius1": T1500G-10MPS(config - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 293
login Description This aaa authentication login command is used to configure a login authentication method list. A method list describes the commands. User Guidelines By default the login authentication method list is "default" with "local" as method1. Example Configure a login authentication method - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 294
enable Description This aaa authentication enable command is used to configure a privilege authentication method list. A method list describes commands. User Guidelines By default the enable authentication method is "default" with "none" as method1. Example Configure a privilege authentication method - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 295
RADIUS server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1X authentication method as "radius1": T1500G-10MPS(config)# aaa - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 296
server group is supported, and the default method is server group "radius". Command Mode Global Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the default 802.1X accounting method as "radius1": T1500G-10MPS(config)# aaa accounting - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 297
to these commands. Example Display the information of the default 802.1X accounting method list: T1500G-10MPS(config)# show aaa accounting 27.17 line telnet Description The line telnet command is used to enter the Line Configuration Mode to configure the telnet terminal line to which you want to - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 298
by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the telnet terminal line as "list1": T1500G-10MPS(config)#line telnet T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 299
line. It is "default" by default, which contains the method "local". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the login authentication method list on the ssh terminal line as "list1": T1500G-10MPS(config)# line - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 300
by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the telnet terminal line as "list2": T1500G-10MPS(config)#line telnet T1500G-10MPS - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 301
line. It is "default" by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the ssh terminal line as "list2": T1500G-10MPS(config)# line - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 302
. It is "default" by default, which contains the method "none". Command Mode Line Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Configure the enable authentication method list on the HTTP access as "list2": T1500G-10MPS(config)# ip http enable - TP-Link T1500G-8T | T1500G-10PSUN V1 CLI Reference Guide Guide - Page 303
method lists of different application modules: telnet, ssh and HTTP. Syntax show aaa global Command Mode Privileged EXEC Mode and Any Configuration Mode Privilege Requirement Only Admin level users have access to these commands. Example Display the AAA function's global status and each application
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
 |
 |
CLI Guide
JetStream 8-Port Gigabit Smart Switch
T1500G-10MPS/T1500G-8T (TL-SG2008)
T1500G-10PS (TL-SG2210P)
REV1.0.2
1910012064