Thermador UCVP36XS Installation Instructions - Page 13

Installation

Get Thermador UCVP36XS PDF manuals and user guides View all Thermador UCVP36XS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

I N S TA L L AT I O N Take measurements 1. Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. However, it is recommended that oversized cabinets be used for easier installation. Custom island designs need to account for deeper cabinets, especially when mounting the blower behind the downdraft. You must also plan for an access door. Cut countertop opening 1. Lay out and cut the cooktop cut-out far enough FORWARD so downdraft will it behind it. 2. Set cooktop in place and slide it as far forward as possible without exposing any gaps. Center and square it with edges of countertop. Pay special attention to the areas of potential interference highlighted below. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough lat countertop for a proper installation. Note that a minimum of 2-7/8" (73 mm) of lat countertop is required behind cooktop (C) and that a minimum of 2-7/8" (73 mm) is necessary between the back edge of the cooktop and the inside of cabinet back (D). FLAT COUNTERTOP (C) 2-7/8" (73 mm) MIN. A T E M P L AT E 2-1/8" (54 mm) MIN. COUNTERTOP COOKTOP DOWNDRAFT 2-7/8" (73 mm) MIN. FRONT TO BACK INSIDE CABINET DEPTH 5/8" (16 mm) MIN. C COOKTOP Template against back B edge of cooktop 3. Place the plastic template against the back lange of the cooktop. D Center the template. Trace around template to mark the downdraft opening. 4. Remove cooktop from countertop. 5. Cut downdraft opening. Be careful not to chip edges of countertop. Installation with electric and induction cooktops Dimension "BT" is thickness of the backsplash. Provide 1/2" (13 mm) clearance between the vent cutout and the backsplash. Any backsplash with a curved radius where it meets the counter will require additional clearance. Thicker backsplashes may be used by increasing the counter and cabinet depths. Set the cooktop into the coutertop opening so that the back edge of the cooktop overlaps the leading edge of the downdraft. Template 2-1/8" (54 mm) Downdraft cutout width: 30" (762 mm) is 27-1/16" (687 mm) 36" (914 mm) is 33-1/16" (840 mm) 25-7/16" - 25-9/16" (646 mm - 649 mm) 22-11/16" - 22-13/16" (576 mm - 579 mm) 19-7/8" - 20" (505 mm - 508 mm) 11/16" (17 mm) BT MIN. 1/2" (13 mm) 2-1/4" (57 mm) Cooktop cutout width Measurements in inches (mm). Page 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Page 13
INSTALLATION
COUNTERTOP
COOKTOP
DOWNDRAFT
FRONT TO BACK
INSIDE CABINET DEPTH
FLAT COUNTERTOP (C)
2-7/8” (73 mm) MIN.
B
A
5/8” (16 mm) MIN.
2-7/8” (73 mm) MIN.
D
C
TEMPLATE
2-1/8” (54 mm) MIN.
Cut countertop opening
1.
±ay out and cut the cooktop cut-out far enough FORWARD so
downdraft will ²t behind it.
2.
Set cooktop in place and slide it as far forward as possible without
exposing any gaps. Center and square it with edges of countertop.
3.
Place the plastic template against the back Lange of the cooktop.
Center the template. Trace around template to mark the
downdraft opening.
4. Remove cooktop from countertop.
5.
Cut downdraft opening. Be careful not to chip edges of countertop.
COOKTOP
Template against back
edge of cooktop
Take measurements
1.
Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. However,
it is recommended that oversized cabinets be used for easier
installation. Custom island designs need to account for deeper
cabinets, especially when mounting the blower behind the
downdraft. You must also plan for an access door.
Pay special attention to the areas of potential interference highlighted
below. A countertop with (A) a raised lip and/or (B) a backsplash may
not allow enough Lat countertop for a proper installation. Note that
a minimum of 2-7/8” (73 mm) of Lat countertop is required behind
cooktop (C) and that a minimum of 2-7/8” (73 mm) is necessary between
the back edge of the cooktop and the inside of cabinet back (D).
Installation with electric and induction cooktops
Dimension “BT” is thickness of
the backsplash. Provide 1/2”
(13 mm) clearance between the
vent cutout and the backsplash.
Any backsplash with a curved
radius where it meets the counter
will require additional clearance.
Thicker backsplashes may be used by
increasing the counter and cabinet
depths.
Set the cooktop into the coutertop
opening so that the back edge of the
cooktop overlaps the leading edge of
the downdraft.
Cooktop cutout width
2-1/4” (57 mm)
BT
MIN.
1/2”
(13 mm)
Downdraft cutout width:
30” (762 mm) is 27-1/16” (687 mm)
36” (914 mm) is 33-1/16” (840 mm)
Template
2-1/8” (54 mm)
19-7/8” - 20”
(505 mm - 508 mm)
22-11/16” - 22-13/16”
(576 mm - 579 mm)
25-7/16” - 25-9/16”
(646 mm - 649 mm)
11/16”
(17 mm)
Measurements in inches (mm).