Thermador UCVP36XS Installation Instructions - Page 21

Attach endcaps to downdraft

Get Thermador UCVP36XS PDF manuals and user guides View all Thermador UCVP36XS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

I N S TA L L AT I O N Connect downdraft to power Attach endcaps to downdraft SPECIAL KEY (INCLUDED) 1. Plug electrical panel cable into lower receptacle as shown. Plug the downdraft's power cord into the 3-pronged receptacle. Make sure that the power cord is routed away from the heat generated by the cooktop. 2. Check operation. 3. Remove all protective ilm and packaging before operation. In order to remove all protective ilm and packaging, raise the intake housing and remove the front panel to access the ilter area. Make-up air damper wiring (if required) (Refer to make-up air damper instructions.) MAKE-UP AIR DAMPER CONTACTS Connects to 2 contacts on electrical panel. ENDCAP RETAINING SCREW Install cooking appliance Align the cooking appliance with downdraft and fasten appliance in place following appliance instructions. Note: Accurate alignment of cooking appliance and downdraft is necessary to ensure that there is no interference when air vent is raised and lowered. There should be a gap of 1/32" - 1/16" (0.79 mm - 1.59 mm) between the back of the cooktop and the front of the downdraft cover. Note: Following procedure applies to both endcaps. 1. Use the included special key to loose the endcap retaining screw. 2. Place the endcap over the bracket. 3. Use the included special key to tighten the endcap retaining screw. 4. Check the operation of the downdraft. Page 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Page 21
INSTALLATION
Connect downdraft to power
1.
Plug electrical panel cable into lower receptacle as shown.
Plug the downdraft’s power cord into the 3-pronged receptacle.
Make sure that the power cord is routed away from the heat
generated by the cooktop.
2.
Check operation.
3.
Remove all protective ²lm and packaging before operation. In order to
remove all protective ²lm and packaging, raise the intake housing and
remove the front panel to access the ²lter area.
Make-up air damper wiring (if required)
(Refer to make-up air damper instructions.)
Connects to 2 contacts on electrical panel.
Install cooking appliance
Align the cooking appliance with downdraft and fasten appliance in
place following appliance instructions.
Note:
Accurate alignment of cooking appliance and downdraft is necessary
to ensure that there is no interference when air vent is raised and lowered.
There should be a gap of 1/32" - 1/16" (0.79 mm - 1.59 mm) between the
back of the cooktop and the front of the downdraft cover.
MAKE-UP AIR
DAMPER
CONTACTS
Attach endcaps to downdraft
Note:
Following procedure applies to both endcaps.
1.
Use the included special key to loose the endcap retaining screw.
2.
Place the endcap over the bracket.
3.
Use the included special key to tighten the endcap retaining screw.
4.
Check the operation of the downdraft.
SPECIAL KEY
(
INCLUDED
)
ENDCAP
RETAINING
SCREW