Tripp Lite SV20KM1P1B Owners Manual for SmartOnline 208V SV-Series 3-Phase Mod - Page 25

SmartOnline SV-Series UPS Operating Mode, Standby, Bypass, Battery, Battery Test, Fault, Converter,

Get Tripp Lite SV20KM1P1B PDF manuals and user guides View all Tripp Lite SV20KM1P1B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

9. Control Panel SmartOnline SV-Series UPS Operating Mode Standby Bypass Line Battery Battery Test Fault Converter ECO Time Y Y Y Y Y Y Y Y Change Password Y Y Y Y Y Y Y Y Audible Alarm Y Y Y Y Y Y Y Y Factory Reset Y EEPROM Reset Y EPO Function Y Save Setting Y Y Table 9.3 9.3.6.2 System The SETUP - SYSTEM screen may be accessed in any UPS operating mode. Some settings may only be amended in certain modes; refer to table 9.4 for details. Output Voltage Set output voltage: 120/127V (Default: 120V) Bypass Setting Converter Mode Voltage - Upper limit: +10/15%; Lower limit: -10/20% (Default: +15/-20%) Frequency - Upper limit: +1/2/4Hz; Lower limit: -1/2/4Hz (Default: +/- 4 Hz) Set "Disable" or "Enable" (Default: Disabled) ECO Mode Set "Disable" or "Enable" (Default: Disabled) Bypass Mode Set "Disable" or "Enable" (Default: Enabled) SYSTEM Auto Restart Cold Start Battery Mode Delay Time* Set "Disable" or "Enable" (Default: Enabled) Set "Disable" or "Enable" (Default: Disabled) Refer to 7.3 Cold Start for more information Set system shutdown delay time in battery mode (0-9990 sec.) System Shutdown Time* Set system shutdown time 0.2 - 99 min. (Default: 0.2 min.) System Restore Time* Set system restore time 0-9999 min. (Default: 001) Redundancy* Charger Test Total Power - Quantity of Power Modules installed Redundancy - Quantity of Power Modules to be redundant Set "Disable" or "Enable" (Default: Disabled) When this feature is enabled and the battery breaker of the UPS system is on, LCD can display the charger voltage 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
25
9. Control Panel
SmartOnline SV-Series UPS Operating Mode
Standby
Bypass
Line
Battery
Battery Test
Fault
Converter
ECO
Time
Y
Y
Y
Y
Y
Y
Y
Y
Change Password
Y
Y
Y
Y
Y
Y
Y
Y
Audible Alarm
Y
Y
Y
Y
Y
Y
Y
Y
Factory Reset
Y
EEPROM Reset
Y
EPO Function
Y
Save Setting
Y
Y
Table 9.3
9.3.6.2 System
The SETUP – SYSTEM screen may be accessed in any UPS operating mode. Some settings may only be amended in certain modes; refer to table
9.4 for details.
SYSTEM
Output Voltage
Bypass Setting
Converter Mode
ECO Mode
Bypass Mode
Auto Restart
Cold Start
Battery Mode Delay Time*
System Shutdown Time*
System Restore Time*
Redundancy*
Charger Test
Set output voltage: 120/127V (Default: 120V)
Voltage – Upper limit: +10/15%; Lower limit: -10/20% (Default: +15/-20%)
Frequency – Upper limit: +1/2/4Hz; Lower limit: -1/2/4Hz (Default: +/- 4 Hz)
Set “Disable” or “Enable” (Default: Disabled)
Set “Disable” or “Enable” (Default: Disabled)
Set “Disable” or “Enable” (Default: Enabled)
Set “Disable” or “Enable” (Default: Enabled)
Set “Disable” or “Enable” (Default: Disabled)
Refer to
7.3 Cold Start
for more information
Set system shutdown delay time in battery mode (0-9990 sec.)
Set system shutdown time 0.2 – 99 min. (Default: 0.2 min.)
Set system restore time 0-9999 min. (Default: 001)
Total Power - Quantity of Power Modules installed
Redundancy - Quantity of Power Modules to be redundant
Set “Disable” or “Enable” (Default: Disabled)
When this feature is enabled and the battery breaker of the UPS system is on, LCD can
display the charger voltage