Yamaha 9000Pro Owner's Manual - Page 186

Remove the SIMM cover., and remove the six screws from the SIMM cover with

Page 186 highlights

Installing Optional Hardware 1-2 Use the same operation as in "Optional Plug-in Board Installation" (page 181). SIMM cover 3 Move to a position facing the rear panel of the keyboard, and remove the six screws from the SIMM cover with a Phillips screwdriver. Do not remove the other screws. 4 Remove the SIMM cover. 5 Insert the SIMMs in the SIMM slots as described below...5-[1] Make sure the orientation is correct. Make sure that the cutout on the SIMM module is aligned with the protruding "key" on the connector slot. Black screws First SIMM SIMM cutout CAUTION • Do not install the SIMM backwards. Slot key 5-[2] Install the first SIMM in the rear slot (the slot closest to the 9000Pro rear panel), inserting it at an angle as shown in the illus- tration. Make sure that the parts at locations A, B, and C are properly aligned. Clamp SIMM hole Clamp CAUTION • Make sure that the entire length of the SIMM is evenly inserted. C A B SIMM hole SIMM notch Slot protrusion 186 Reference 184

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250

Installing Optional Hardware
Installing Optional Hardware
186
Reference
1-2
Use the same operation as in "Optional Plug-in Board
Installation" (page 181).
3
Move to a position facing the rear panel of the keyboard,
and remove the six screws from the SIMM cover with a
Phillips screwdriver. Do not remove the other screws.
4
Remove the SIMM cover.
5
Insert the SIMMs in the SIMM slots as described below.
....................................................................................................................
5
-[1]
Make sure the orientation is correct. Make sure that the cutout on
the SIMM module is aligned with the protruding
key
on the con-
nector slot.
5
-[2]
Install the
rst SIMM in the rear slot (the slot closest to the
9000Pro rear panel), inserting it at an angle as shown in the illus-
tration.
Make sure that the parts at locations A, B, and C are properly
aligned.
Black
screws
SIMM
cover
First SIMM
SIMM cutout
Slot key
CAUTION
Do not install the SIMM back-
wards.
A
B
C
Clamp
SIMM hole
Slot protrusion
SIMM notch
SIMM hole
Clamp
CAUTION
Make sure that the entire length of
the SIMM is evenly inserted.
184