Yamaha RX-V563 Owner's Manual - Page 97

Remote control, Resetting the system, then press

Get Yamaha RX-V563 - AV Receiver PDF manuals and user guides
UPC - 027108929972
View all Yamaha RX-V563 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

■ Remote control Troubleshooting Problem The remote control does not work nor function properly. Cause Wrong distance or angle. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. The batteries are weak. The remote control code is not correctly set. Even if the remote control code is correctly set, there are some models that do not respond to the remote control. Remedy The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. Reposition this unit. Replace all batteries. Set the remote control code correctly using "List of remote control codes" at the end of this manual. Try setting another code for the same manufacturer using "List of remote control codes" at the end of this manual. See page 25 - 3 78 78 ■ Resetting the system Use this feature to reset all the parameters of this unit to the initial factory settings. 1 Press CSYSTEM OFF on the front panel to set this unit to the standby mode. 2 Press and hold NTONE CONTROL and then press AMAIN ZONE ON/OFF to turn on this unit. The advanced setup menu appears in the front panel display. Notes • This procedure completely resets all the parameters of this unit including the "SET MENU" parameters. However, the advanced setup menu parameters will not be initialized. • The initial factory settings are activated next time you turn on this unit. y To cancel the initialization procedure at any time without making any changes, press PSTRAIGHT repeatedly to select "CANCEL" and then press AMAIN ZONE ON/OFF. 3 Press OPROGRAM l / h to select "INIT.". 4 Press PSTRAIGHT repeatedly to select "RESET". Select "CANCEL" to cancel the initialization procedure without making any changes. 5 Press AMAIN ZONE ON/OFF to confirm your selection and set this unit to the standby mode. ADDITIONAL INFORMATION English 93 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
93
En
Troubleshooting
English
ADDITIONAL
INFORMATION
■
Remote control
■
Resetting the system
Use this feature to reset all the parameters of this unit to
the initial factory settings.
1
Press
C
SYSTEM OFF
on the front panel to
set this unit to the standby mode.
2
Press and hold
N
TONE CONTROL
and
then press
A
MAIN ZONE ON/OFF
to turn
on this unit.
The advanced setup menu appears in the front panel
display.
3
Press
O
PROGRAM
l
/
h
to select “INIT.”.
4
Press
P
STRAIGHT
repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
5
Press
A
MAIN ZONE ON/OFF
to confirm
your selection and set this unit to the
standby mode.
•
This procedure completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
•
The initial factory settings are activated next time you turn on
this unit.
y
To cancel the initialization procedure at any time without making
any changes, press
P
STRAIGHT
repeatedly to select
“CANCEL” and then press
A
MAIN ZONE ON/OFF
.
Problem
Cause
Remedy
See
page
The remote control
does not work nor
function properly.
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
25
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
78
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
78
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Notes