Home » ZyXEL Manuals » Networking » ZyXEL LTE5121 » Manual Viewer

ZyXEL LTE5121 User Guide - Page 173

Table 71, Label, Description

Get ZyXEL LTE5121 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

Chapter 17 VoIP Each field is described in the following table. Table 71 SIP AccountEdit LABEL DESCRIPTION SIP Service Provider Selection Service Provider Selection Select the SIP service provider profile you want to use for the SIP account you configure in this screen. This field is view-only if you are editing the SIP account. SIP Account Selection SIP Account Selection This shows the SIP account you are configuring. General SIP Account Select the Active SIP Account check box if you want to use this account. Clear it if you do not want to use this account. SIP Account Number Enter your SIP number. In the full SIP URI, this is the part before the @ symbol. You can use up to 127 printable ASCII characters. Authentication Username Enter the user name for registering this SIP account, exactly as it was given to you. You can use up to 95 printable ASCII characters. Password Enter the password for registering this SIP account, exactly as it was given to you. You can use up to 95 printable ASCII characters. URL Type URL Type Select whether or not to include the SIP service domain name when the LTE Device sends the SIP number. SIP - include the SIP service domain name. TEL - do not include the SIP service domain name. Voice Features Primary Select the type of voice coder/decoder (codec) that you want the LTE Device to Compression Type use. G.711 provides higher voice quality but requires more bandwidth (64 kbps). Secondary • Compression Type • Third Compression Type • • G.711MuLaw is typically used in North America and Japan. G.711ALaw is typically used in Europe. G.726-32 operates at 16, 24, 32 or 40 kbps. G.722 operates at 48, 56 and 64 kbps. The LTE Device must use the same codec as the peer. When two SIP devices start a SIP session, they must agree on a codec. Select the LTE Device's first choice for voice coder/decoder. Select the LTE Device's second choice for voice coder/decoder. Select None if you only want the LTE Device to accept the first choice. Speaking Volume Control Listening Volume Control Active G.168 (Echo Cancellation) Select the LTE Device's third choice for voice coder/decoder. Select None if you only want the LTE Device to accept the first or second choice. Enter the loudness that the LTE Device uses for speech that it sends to the peer device. Minimum is the quietest, and Maximum is the loudest. Enter the loudness that the LTE Device uses for speech that it receives from the peer device. Minimum is the quietest, and Maximum is the loudest. Select this if you want to eliminate the echo caused by the sound of your voice reverberating in the telephone receiver while you talk. LTE-5121 User's Guide 173

Section	Page
LTE5121	1
Contents Overview	3
Table of Contents	5
User’s Guide	13
Introduction	15
1.1 Overview	15
1.2 Applications for the LTE Device	15
1.2.1 Internet Access	15
1.2.2 VoIP Features	16
1.3 The WLAN Button	16
1.4 The WPS Button	16
1.5 Ways to Manage the LTE Device	17
1.6 Good Habits for Managing the LTE Device	17
1.7 LEDs (Lights)	17
1.8 The RESET Button	19
1.9 Wall-mounting Instructions	19
Introducing the Web Configurator	23
2.1 Overview	23
2.1.1 Accessing the Web Configurator	23
2.2 The Web Configurator Layout	25
2.2.1 Title Bar	25
2.2.2 Main Window	25
Technical Reference	27
Connection Status and System Info	29
3.1 Overview	29
3.2 The Connection Status Screen	29
3.3 The System Info Screen	30
Broadband	35
4.1 Overview	35
4.1.1 What You Can Do in this Chapter	35
4.1.2 What You Need to Know	35
4.1.3 Before You Begin	36
4.2 The Broadband Screen	36
4.2.1 Edit Internet Connection	38
4.3 The SIM Screen	39
4.3.1 PUK Code Screen	40
4.4 Technical Reference	41
Wireless	43
5.1 Overview	43
5.1.1 What You Can Do in this Chapter	43
5.1.2 Wireless Network Overview	43
5.1.3 Before You Begin	45
5.2 The Wireless General Screen	45
5.2.1 No Security	47
5.2.2 Basic (Static WEP/Shared WEP Encryption)	47
5.2.3 More Secure (WPA(2)-PSK)	49
5.2.4 WPA(2) Authentication	50
5.3 The More AP Screen	51
5.3.1 Edit More AP	52
5.4 The WPS Screen	53
5.5 The WMM Screen	55
5.6 Scheduling Screen	57
5.7 Channel Status Screen	57
5.8 Technical Reference	58
5.8.1 Additional Wireless Terms	59
5.8.2 Wireless Security Overview	59
5.8.3 Signal Problems	61
5.8.4 BSS	61
5.8.5 MBSSID	62
5.8.6 WiFi Protected Setup (WPS)	62
Home Networking	71
6.1 Overview	71
6.1.1 What You Can Do in this Chapter	71
6.1.2 What You Need To Know	71
6.2 The LAN Setup Screen	74
6.3 The Static DHCP Screen	75
6.3.1 Before You Begin	75
6.4 The UPnP Screen	77
6.5 The File Sharing Screen	77
6.5.1 Before You Begin	78
6.5.2 Add/Edit File Sharing	79
6.6 The Media Server Screen	80
6.7 The Printer Server Screen	81
6.7.1 Before You Begin	81
6.8 Technical Reference	82
6.9 Installing UPnP in Windows Example	86
6.10 Using UPnP in Windows XP Example	89
Static Route	95
7.1 Overview	95
7.2 Configuring Static Route	96
7.2.1 Add/Edit Static Route	97
DNS Route	99
8.1 Overview	99
8.1.1 What You Can Do in this Chapter	99
8.2 The DNS Route Screen	100
8.2.1 Add/Edit DNS Route Edit	100
Quality of Service (QoS)	103
9.1 Overview	103
9.1.1 What You Can Do in this Chapter	103
9.1.2 What You Need to Know	103
9.2 The QoS General Screen	104
9.3 The Queue Setup Screen	105
9.3.1 Add/Edit a QoS Queue	106
9.4 The Class Setup Screen	107
9.4.1 Add/Edit QoS Class	109
9.5 The QoS Monitor Screen	112
9.6 QoS Technical Reference	113
9.6.1 DiffServ	113
Network Address Translation (NAT)	115
10.1 Overview	115
10.1.1 What You Can Do in this Chapter	115
10.1.2 What You Need To Know	115
10.2 The Port Forwarding Screen	116
10.2.1 The Port Forwarding Screen	117
10.2.2 The Port Forwarding Edit Screen	118
10.3 The DMZ Screen	119
10.4 The Sessions Screen	119
10.5 The ALG Screen	120
10.6 Technical Reference	120
10.6.1 NAT Definitions	121
10.6.2 What NAT Does	121
10.6.3 How NAT Works	121
Dynamic DNS	123
11.1 Overview	123
11.1.1 What You Need To Know	123
11.2 The Dynamic DNS Screen	123
Firewall	125
12.1 Overview	125
12.1.1 What You Can Do in this Chapter	125
12.1.2 What You Need to Know	126
12.2 The General Screen	126
12.3 The Services Screen	127
12.3.1 The Add New Services Entry Screen	128
12.4 The Access Control Screen	129
12.4.1 The Add New ACL Rule/Edit Screen	130
12.5 The DoS Screen	131
12.6 Firewall Technical Reference	132
12.6.1 Guidelines For Enhancing Security With Your Firewall	132
12.6.2 Security Considerations	132
MAC Filter	133
13.1 Overview	133
13.1.1 What You Need to Know	133
13.2 The MAC Filter Screen	133
Parental Control	135
14.1 Overview	135
14.2 The Parental Control Screen	135
14.2.1 Add/Edit a Parental Control Rule	136
Certificates	139
15.1 Overview	139
15.1.1 What You Can Do in this Chapter	139
15.1.2 What You Need to Know	139
15.1.3 Verifying a Certificate	140
15.2 Local Certificates	141
15.3 Trusted CA	143
15.4 Trusted CA Import	143
15.5 View Certificate	144
15.6 VPN Certificates	145
15.7 VPN Certificate Import	147
VPN	149
16.1 Overview	149
16.2 The VPN Screen	149
16.3 IPSec VPN: Add	150
16.4 VPN Monitor Screen	155
16.5 Technical Reference	155
16.5.1 IPSec Architecture	156
16.5.2 Encapsulation	156
16.5.3 IKE Phases	157
16.5.4 Negotiation Mode	158
16.5.5 IPSec and NAT	159
16.5.6 VPN, NAT, and NAT Traversal	159
16.5.7 ID Type and Content	160
16.5.8 Pre-Shared Key	161
16.5.9 Diffie-Hellman (DH) Key Groups	161
VoIP	163
17.1 Overview	163
17.1.1 What You Can Do in this Chapter	163
17.1.2 What You Need to Know	163
17.1.3 Before You Begin	164
17.2 The SIP Service Provider Screen	165
17.3 The SIP Account Screen	171
17.3.1 Add/Edit SIP Account	172
17.4 Multiple SIP Accounts	175
17.5 Phone Screen	175
17.5.1 Edit Phone Device	175
17.6 The Phone Region Screen	177
17.7 The Call Rule Screen	177
17.8 Technical Reference	179
17.8.1 VoIP	179
17.8.2 SIP	179
17.8.3 Quality of Service (QoS)	183
17.8.4 Phone Services Overview	184
System Monitor	187
18.1 Overview	187
18.1.1 What You Can Do in this Chapter	187
18.1.2 What You Need To Know	187
18.2 The LTE Status Screen	188
18.3 The System Log Screen	190
18.4 The Phone Log Screen	191
18.5 The VoIP Call History Screen	192
18.6 The WAN Status Screen	192
18.7 The LAN Status Screen	193
18.8 The NAT Status Screen	194
18.9 The VoIP Status Screen	195
User Account	197
19.1 Overview	197
19.2 The User Account Screen	197
Remote MGMT	199
20.1 Overview	199
20.1.1 What You Need to Know	199
20.2 The Remote MGMT Screen	200
SNMP	201
21.1 Overview	201
21.2 The SNMP Screen	201
System	203
22.1 Overview	203
22.1.1 What You Need to Know	203
22.2 The System Screen	203
Time Setting	205
23.1 Overview	205
23.2 The Time Setting Screen	205
Log Setting	207
24.1 Overview	207
24.2 The Log Setting Screen	207
Firmware Upgrade	209
25.1 Overview	209
25.2 The Firmware Upgrade Screen	209
Backup/Restore	211
26.1 Overview	211
26.2 The Backup/Restore Screen	211
26.3 The Reboot Screen	213
Diagnostic	215
27.1 Overview	215
27.2 The Ping/TraceRoute Screen	215
27.3 LTE Diagnostic Screen	216
Troubleshooting	217
28.1 Overview	217
28.2 Power, Hardware Connections, and LEDs	217
28.3 LTE Device Access and Login	218
28.4 Internet Access	220
28.5 Wireless Internet Access	221
28.6 Phone Calls and VoIP	222
28.7 USB Device Connection	222
28.8 UPnP	223
Legal Information	225

Match case Limit results 1 per page

Chapter 17 VoIP

LTE-5121 User’s Guide

173

Each field is described in the following table.

Table 71

SIP Account

Edit

LABEL

DESCRIPTION

SIP Service Provider Selection

Service Provider

Selection

Select the SIP service provider profile you want to use for the SIP account you

configure in this screen.

This field is view-only if you are editing the SIP account.

SIP Account Selection

SIP Account

Selection

This shows the SIP account you are configuring.

General

SIP Account

Select the

Active SIP Account

check box if you want to use this account. Clear

it if you do not want to use this account.

SIP Account

Number

Enter your SIP number. In the full SIP URI, this is the part before the @ symbol.

You can use up to 127 printable ASCII characters.

Authentication

Username

Enter the user name for registering this SIP account, exactly as it was given to

you. You can use up to 95 printable ASCII characters.

Password

Enter the password for registering this SIP account, exactly as it was given to

you. You can use up to 95 printable ASCII characters.

URL Type

Select whether or not to include the SIP service domain name when the LTE

Device sends the SIP number.

SIP

- include the SIP service domain name.

TEL

- do not include the SIP service domain name.

Voice Features

Primary

Compression Type

Secondary

Compression Type

Third

Compression Type

Select the type of voice coder/decoder (codec) that you want the LTE Device to

use. G.711 provides higher voice quality but requires more bandwidth (64 kbps).

•

G.711MuLaw

is typically used in North America and Japan.

•

G.711ALaw

is typically used in Europe.

•

G.726-32

operates at 16, 24, 32 or 40 kbps.

•

G.722

operates at 48, 56 and 64 kbps. The LTE Device must use the same

codec as the peer. When two SIP devices start a SIP session, they must

agree on a codec.

Select the LTE Device’s first choice for voice coder/decoder.

Select the LTE Device’s second choice for voice coder/decoder. Select

None

you only want the LTE Device to accept the first choice.

Select the LTE Device’s third choice for voice coder/decoder. Select

None

if you

only want the LTE Device to accept the first or second choice.

Speaking

Volume

Control

Enter the loudness that the LTE Device uses for speech that it sends to the peer

device.

Minimum

is the quietest, and

Maximum

is the loudest.

Listening

Volume

Control

Enter the loudness that the LTE Device uses for speech that it receives from the

peer device.

Minimum

is the quietest, and

Maximum

is the loudest.

Active G.168

(Echo

Cancellation)

Select this if you want to eliminate the echo caused by the sound of your voice

reverberating in the telephone receiver while you talk.