Home » ZyXEL Manuals » Bridges & Routers » ZyXEL NBG6503 » Manual Viewer

ZyXEL NBG6503 User Guide - Page 110

What You Need To Know

Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 12 LAN 12.3 What You Need To Know The actual physical connection determines whether the Router ports are LAN or WAN ports. There are two separate IP networks, one inside the LAN network and the other outside the WAN network as shown next. Figure 77 LAN and WAN IP Addresses The LAN parameters of the Router are preset in the factory with the following values: • IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits) • DHCP server enabled with 32 client IP addresses starting from 192.168.1.33. These parameters should work for the majority of installations. If your ISP gives you explicit DNS server address(es), read the embedded Web Configurator help regarding what fields need to be configured. 12.3.1 IP Pool Setup The Router is pre-configured with a pool of 32 IP addresses starting from 192.168.1.33 to 192.168.1.64. This configuration leaves 31 IP addresses (excluding the Router itself) in the lower range (192.168.1.2 to 192.168.1.32) for other server computers, for instance, servers for mail, FTP, TFTP, web, etc., that you may have. 12.3.2 LAN TCP/IP The Router has built-in DHCP server capability that assigns IP addresses and DNS servers to systems that support DHCP client capability. 12.3.3 IP Alias IP alias allows you to partition a physical network into different logical networks over the same Ethernet interface. The Router supports three logical LAN interfaces via its single physical Ethernet interface with the Router itself as the gateway for each LAN network. 110 NBG6503 User's Guide

Section	Page
NBG6503	1
Contents Overview	3
Table of Contents	5
User’s Guide	13
Getting to Know Your Router	15
1.1 Overview	15
1.2 Applications	15
1.3 Ways to Manage the Router	15
1.4 Good Habits for Managing the Router	16
1.5 LEDs	17
1.6 The WPS Button	18
1.7 Wall Mounting	18
Connection Wizard	21
2.1 Overview	21
2.2 Accessing the Wizard	21
2.3 Connect to Internet	22
2.3.1 Connection Type: DHCP	23
2.3.2 Connection Type: Static IP	23
2.3.3 Connection Type: PPPoE	24
2.3.4 Connection Type: PPTP	25
2.4 Router Password	27
2.5 Wireless Security	27
2.5.1 Wireless Security: No Security	27
2.5.2 Wireless Security: WPA-PSK/WPA2-PSK	28
Introducing the Web Configurator	31
3.1 Overview	31
3.2 Accessing the Web Configurator	31
3.2.1 Login Screen	31
3.2.2 Password Screen	32
3.2.3 Home Screen	33
3.3 Resetting the Router	35
3.3.1 Procedure to Use the Reset Button	35
Monitor	37
4.1 Overview	37
4.2 What You Can Do	37
4.3 The Log Screen	37
4.3.1 View Log	37
4.4 BW MGMT Monitor	39
4.5 DHCP Table	39
4.6 Packet Statistics	40
4.7 WLAN 2.4G Station Status	41
4.8 WLAN 5G Station Status	41
Router Modes	43
5.1 Overview	43
5.1.1 Web Configurator Modes	43
5.1.2 Device Modes	43
Easy Mode	45
6.1 Overview	45
6.2 What You Can Do	46
6.3 What You Need to Know	46
6.4 Navigation Panel	47
6.5 Network Map	47
6.6 Control Panel	48
6.6.1 Game Engine	49
6.6.2 Power Saving	49
6.6.3 Content Filter	51
6.6.4 Bandwidth MGMT	51
6.6.5 Firewall	52
6.6.6 Wireless Security	52
6.6.7 WPS	54
6.7 Status Screen in Easy Mode	55
Router Mode	57
7.1 Overview	57
7.2 What You Can Do	57
7.3 Status Screen	58
7.3.1 Navigation Panel	61
Access Point Mode	65
8.1 Overview	65
8.2 What You Can Do	65
8.3 What You Need to Know	65
8.3.1 Setting your Router to AP Mode	66
8.3.2 Accessing the Web Configurator in Access Point Mode	66
8.3.3 Configuring your WLAN, Bandwidth Management and Maintenance Settings	67
8.4 AP Mode Status Screen	68
8.5 LAN Screen	70
Tutorials	73
9.1 Overview	73
9.2 Connecting to the Internet from an Access Point	73
9.3 Configuring Wireless Security Using WPS	73
9.3.1 Push Button Configuration (PBC)	74
9.3.2 PIN Configuration	75
9.4 Enabling and Configuring Wireless Security (No WPS)	77
9.4.1 Configure Your Notebook	78
Technical Reference	81
Wireless LAN	83
10.1 Overview	83
10.2 What You Can Do	83
10.3 What You Should Know	84
10.3.1 Wireless Security Overview	84
10.4 General Wireless LAN 2.4G/5G Screen	86
10.4.1 No Security	87
10.4.2 WEP Encryption	88
10.4.3 WPA-PSK/WPA2-PSK	90
10.5 MAC Filter	90
10.6 Wireless LAN Advanced Screen	91
10.7 Quality of Service (QoS) Screen	93
10.8 WPS Screen	94
10.9 WPS Station Screen	95
10.10 Scheduling Screen	96
10.11 WDS Screen	97
WAN	99
11.1 Overview	99
11.2 What You Can Do	99
11.3 What You Need To Know	99
11.3.1 Configuring Your Internet Connection	100
11.3.2 Multicast	101
11.4 Internet Connection	102
11.4.1 Ethernet Encapsulation	102
11.4.2 PPPoE Encapsulation	103
11.4.3 PPTP Encapsulation	105
11.5 Advanced WAN Screen	108
LAN	109
12.1 Overview	109
12.2 What You Can Do	109
12.3 What You Need To Know	110
12.3.1 IP Pool Setup	110
12.3.2 LAN TCP/IP	110
12.3.3 IP Alias	110
12.4 LAN IP Screen	111
12.5 IP Alias Screen	111
DHCP Server	113
13.1 Overview	113
13.2 What You Can Do	113
13.3 General Screen	113
13.4 Advanced Screen	114
Network Address Translation (NAT)	117
14.1 Overview	117
14.2 What You Can Do	117
14.3 General NAT Screen	118
14.4 NAT Application Screen	118
14.5 NAT Advanced Screen	120
14.5.1 Trigger Port Forwarding Example	122
14.5.2 Two Points To Remember About Trigger Ports	122
Dynamic DNS	123
15.1 Overview	123
15.2 What You Can Do	123
15.3 What You Need To Know	123
15.4 Dynamic DNS Screen	123
Static Route	125
16.1 Overview	125
16.2 What You Can Do	125
16.3 IP Static Route Screen	126
Firewall	129
17.1 Overview	129
17.2 What You Can Do	129
17.3 What You Need To Know	130
17.4 General Firewall Screen	130
17.5 Services Screen	131
Content Filter	133
18.1 Overview	133
18.2 What You Can Do	133
18.3 What You Need To Know	133
18.3.1 Content Filtering Profiles	133
18.4 Content Filter Screen	134
Bandwidth Management	137
19.1 Overview	137
19.2 What You Can Do	137
19.3 What You Need To Know	138
19.4 General Screen	138
19.5 Advanced Screen	138
19.5.1 Rule Configuration: Application Rule Configuration	141
19.5.2 Rule Configuration: User Defined Service Rule Configuration	142
19.6 Monitor Screen	143
19.6.1 Predefined Bandwidth Management Services	143
Remote Management	145
20.1 Overview	145
20.2 What You Can Do	145
20.3 What You Need to Know	145
20.3.1 Remote Management and NAT	145
20.3.2 System Timeout	146
20.4 WWW Screen	146
Universal Plug-and-Play (UPnP)	147
21.1 Overview	147
21.2 What You Can Do	147
21.3 What You Need to Know	147
21.3.1 NAT Traversal	147
21.3.2 Cautions with UPnP	148
21.4 UPnP Screen	148
21.5 Technical Refereance	148
21.5.1 Using UPnP in Windows XP Example	148
21.5.2 Web Configurator Easy Access	151
Maintenance	155
22.1 Overview	155
22.2 What You Can Do	155
22.3 General Screen	155
22.4 Password Screen	156
22.5 Time Setting Screen	157
22.6 Firmware Upgrade Screen	158
22.7 Configuration Backup/Restore Screen	160
22.8 Restart Screen	161
22.9 System Operation Mode Overview	161
22.10 Sys OP Mode Screen	163
Troubleshooting	165
23.1 Power, Hardware Connections, and LEDs	165
23.2 Router Access and Login	166
23.3 Internet Access	167
23.4 Resetting the Router to Its Factory Defaults	169
23.5 Wireless Router/AP Troubleshooting	169
IP Addresses and Subnetting	171
Setting Up Your Computer’s IP Address	181
Wireless LANs	209
Common Services	223
Legal Information	227

Match case Limit results 1 per page

Chapter 12 LAN

NBG6503 User’s Guide

110

12.3

What You Need To Know

The actual physical connection determines whether the Router ports are LAN or WAN ports. There

are two separate IP networks, one inside the LAN network and the other outside the WAN network

as shown next.

Figure 77

LAN and WAN IP Addresses

The LAN parameters of the Router are preset in the factory with the following values:

•

IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits)

•

DHCP server enabled with 32 client IP addresses starting from 192.168.1.33.

These parameters should work for the majority of installations. If your ISP gives you explicit DNS

server address(es), read the embedded Web Configurator help regarding what fields need to be

configured.

12.3.1

IP Pool Setup

The Router is pre-configured with a pool of 32 IP addresses starting from 192.168.1.33 to

192.168.1.64. This configuration leaves 31 IP addresses (excluding the Router itself) in the lower

range (192.168.1.2 to 192.168.1.32) for other server computers, for instance, servers for mail,

FTP, TFTP, web, etc., that you may have.

12.3.2

LAN TCP/IP

The Router has built-in DHCP server capability that assigns IP addresses and DNS servers to

systems that support DHCP client capability.

12.3.3

IP Alias

IP alias allows you to partition a physical network into different logical networks over the same

Ethernet interface. The Router supports three logical LAN interfaces via its single physical Ethernet

interface with the Router itself as the gateway for each LAN network.