Asus CUR-DLS CUR-DLS User Manual - Page 17

System Memory DIMM - dual

Page 17 highlights

3. HARDWARE SETUP 3.5 System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) "registered" Synchronous Dynamic Random Access Memory (SDRAM) of 64, 128, 256, 512, 1024MB with Serial Presence Detect (SPD). ECC memory modules must be used to provide reliability enhancements. Memory speed setup is recommended through SDRAM Configuration in 4.4.1 Chip Configuration. IMPORTANT: This motherboard's chipset only supports 64Mbit, 128Mbit, and 256Mbit "registered" SDRAMs with ECC. This motherboard only operates using synchronous data transfers to the memory. When you use a processor with 100MHz FSB, it will require that the memory supports 100MHz. When you use a processor with 133MHz FSB, it will require that the memory supports 133MHz or else bootup may not be possible. 3.5.1 SDRAM Configurations Technology Configuration Module # Chips 64Mbit 8M x 8 Single-Sided 9 Double-Sided 18 64Mbit 16M x 4 Double-Sided 18 Double-Sided & Stacked 36 128Mbit 32M x 4 Double-Sided 18 Double-Sided & Stacked 36 128Mbit 16M x 8 Single-Sided 9 Double-Sided 18 256Mbit 32M x 8 Single-Sided 9 Double-Sided 18 256Mbit 64M x 4 Single-Sided 18 Double-Sided & Stacked 36 Memory (MB) 64 128 128 256 256 512 128 256 128 256 512 1024 3. H/W SETUP System Memory ASUS CUR-DLS User's Manual 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110

ASUS CUR-DLS User’s Manual
17
3. HARDWARE SETUP
System Memory
3. H/W SETUP
3.5
System Memory (DIMM)
NOTE:
No hardware or BIOS setup is required after adding or removing memory.
This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are
available for
3.3Volt
(power level) “registered” Synchronous Dynamic Random Ac-
cess Memory (SDRAM) of 64, 128, 256, 512, 1024MB with Serial Presence Detect
(SPD). ECC memory modules must be used to provide reliability enhancements.
Memory speed setup is recommended through
SDRAM Configuration
in
4.4.1
Chip Configuration
.
3.5.1
SDRAM Configurations
Technology
Configuration
Module
# Chips
Memory
(MB)
64Mbit
8M x
8
Single-Sided
9
64
Double-Sided
18
128
64Mbit
16M x 4
Double-Sided
18
128
Double-Sided & Stacked
36
256
128Mbit
32M x 4
Double-Sided
18
256
Double-Sided & Stacked
36
512
128Mbit
16M x 8
Single-Sided
9
128
Double-Sided
18
256
256Mbit
32M x 8
Single-Sided
9
128
Double-Sided
18
256
256Mbit
64M x 4
Single-Sided
18
512
Double-Sided & Stacked
36
1024
IMPORTANT:
This motherboard’s chipset only supports 64Mbit, 128Mbit, and
256Mbit “registered” SDRAMs with ECC. This motherboard only operates using
synchronous data transfers to the memory. When you use a processor with 100MHz
FSB, it will require that the memory supports 100MHz.
When you use a proces-
sor with 133MHz FSB, it will require that the memory supports 133MHz or
else bootup may not be possible.