Brother International DCP-8060 Users Manual - English - Page 72

Clear/Back, Copy operation in progress, Start, Stop/Exit, Printing operation in process, Job cancel - drum reset

Get Brother International DCP-8060 PDF manuals and user guides
UPC - 012502615064
View all Brother International DCP-8060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Error Message Drum Near End Cause The drum unit is near the end of its life. Action Use the drum unit until you have a print quality problem; then replace the drum unit with a new one. See Replacing the drum unit (DR-520) on page 76 The drum counter was not reset when a new drum was installed. 1. Open the front cover, and then press Clear/Back. Duplex The duplex tray is not installed Disabled properly. (DCP-8065DN only) Dust on Drum The primary corona wire on the drum unit needs to be cleaned. 2. Press 1 to reset. Remove the duplex tray and install it again. Clean the primary corona wire on the drum unit. (See Cleaning the corona wire on page 71.) Fuser Error The temperature of fuser unit does Turn the power switch off, wait a few seconds, not rise at a specified temperature and then turn it on again. Leave the machine for within specified time. 15 minutes with the power on. No Paper No Tray Out of Memory The fuser unit is too hot. The machine is out of paper or paper is not properly loaded in the paper tray. The paper tray is not completely closed. The machine's memory is full. Do one of the following: „ Refill the paper in the paper tray or MP tray. „ Remove the paper and load it again. Close the paper tray properly. Copy operation in progress Do one of the following: „ Press Start to copy the scanned pages. „ Press Stop/Exit and wait until the other operations in progress finish, and then try again. Printing operation in process Do one of the following: „ Reduce print resolution. (See Advanced tab in the Software User's Guide on the CD-ROM.) „ Clear the data from the memory by pressing Job cancel. Paper Jam Back Paper Jam Duplex The paper is jammed in the back of the machine. The paper is jammed in the duplex tray. (See Paper jams on page 63.) (See Paper jams on page 63.) Paper Jam Inside The paper is jammed inside the machine. (See Paper jams on page 63.) Paper Jam MPTray The paper is jammed in the MP tray (See Paper jams on page 63.) of the machine. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
60
Drum Near End
The drum unit is near the end of its
life.
Use the drum unit until you have a print quality
problem; then replace the drum unit with a new
one.
See
Replacing the drum unit (DR-520)
on page 76
The drum counter was not reset
when a new drum was installed.
1. Open the front cover, and then press
Clear/Back
.
2. Press
1
to reset.
Duplex
Disabled
(DCP-8065DN only)
The duplex tray is not installed
properly.
Remove the duplex tray and install it again.
Dust on Drum
The primary corona wire on the
drum unit needs to be cleaned.
Clean the primary corona wire on the drum unit.
(See
Cleaning the corona wire
on page 71.)
Fuser Error
The temperature of fuser unit does
not rise at a specified temperature
within specified time.
Turn the power switch off, wait a few seconds,
and then turn it on again. Leave the machine for
15 minutes with the power on.
The fuser unit is too hot.
No Paper
The machine is out of paper or
paper is not properly loaded in the
paper tray.
Do one of the following:
Refill the paper in the paper tray or MP tray.
Remove the paper and load it again.
No Tray
The paper tray is not completely
closed.
Close the paper tray properly.
Out of Memory
The machine’s memory is full.
Copy operation in progress
Do one of the following:
Press
Start
to copy the scanned pages.
Press
Stop/Exit
and wait until the other
operations in progress finish, and then try
again.
Printing operation in process
Do one of the following:
Reduce print resolution. (See
Advanced tab
in the Software User’s Guide on the
CD-ROM
.)
Clear the data from the memory by pressing
Job cancel
.
Paper Jam
Back
The paper is jammed in the back of
the machine.
(See
Paper jams
on page 63.)
Paper Jam
Duplex
The paper is jammed in the duplex
tray.
(See
Paper jams
on page 63.)
Paper Jam
Inside
The paper is jammed inside the
machine.
(See
Paper jams
on page 63.)
Paper Jam
MPTray
The paper is jammed in the MP tray
of the machine.
(See
Paper jams
on page 63.)
Error Message
Cause
Action