Home » Brother International Manuals » Sewing Machines » Brother International KE-436C » Manual Viewer

Brother International KE-436C Instruction Manual - English - Page 60

Memory switches 20 - 2F

Get Brother International KE-436C PDF manuals and user guides

View all Brother International KE-436C manuals

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

11. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES Memory switches (20 - 2F) Switch No. memo-20 memo-21 memo-22 memo-23 memo-24 memo-25 memo-26 memo-27 memo-28 memo-29 memo-2A memo-2b memo-2c memo-2d memo-2E memo-2F Motion when set to ON Initial value During feed test operation, jump feeding 100 stitches at a time is possible using the STEP BACK switch. After the home position is detected and the machine moves to the sewing start position, the work clamp rises automatically. − − − The enlargement and reduction ratio settings at the operation panel are fixed at the values when memo-25 was set to ON. Thread trimming is not carried out. The sewing speed setting at the opration panel is fixed at the value when memo-27 was set to ON. Set to ON when using the thread take-up device. Work clamp lifting and lower thread winding before home position detection are disabled. − − − − − When the input voltage is being checked, the display shows the temperature of the heat sink on the main circuit board instead of the voltage. − ON − : OFF KE-436C 54

Section	Page
front	1
SAFETY INSTRUCTIONS	2
2. Notes on safety	3
3. Warning labels	5
CONTENTS	6
1. NAME OF EACH PART	7
2. SPECIFICATIONS	8
2-1. Specifications	8
3. INSTALLATION	9
3-1. Power table	9
3-2. Installing the control box	10
3-3. Installing the rubber cushions	11
3-4. Installing the oil pan	11
3-5. Installing the cushions	11
3-6. Installing the switching plate	12
3-7. Installing the machine head	12
3-8. Installing the head rest	13
3-9. Installing the liquid cooling tank, optional	13
3-10. Installing the operation panel	13
3-11. Installing the programmer (option)	14
3-12. Connecting the ground wire	14
3-13. Connecting the cords	15
3-14. Piping	17
3-15. Installing the belt cover	19
3-16. Installing the foot switch	19
3-17. Installing the needle sub plate	20
3-18. Installing the spool stand	21
3-19. Installing the eye guard	21
4. LUBRICATION	22
4-1. Lubrication points	22
5. USING THE OPERATION PANEL	23
5-1. Explanation of panel	23
5-2. Using the floppy disk	25
5-3. Using the program R/W (Read/Write) switch	27
5-4. Operating the foot switch	28
5-5. Using the TEST switch (Checking the sewing pattern)	28
5-6. Using the emergency stop switch	29
5-7. Using the thread wiper switch	29
5-8. Adjusting the sewing SPEED control	30
5-9. Changing the X-SCALE and Y-SCALE settings	30
5-10. Using the bobbin thread counter	31
5-11. Using production counter	32
5-12. Using single split mode	33
5-13. Shifting a stitch pattern	34
6. CORRECT USE	35
6-1. Selecting the needle and thread	35
6-2. Installing the needle	35
6-3. Threading the upper thread	35
6-4. Winding the lower thread	36
6-5. Replacing the bobbin case and threading the thread	37
6-6. Thread tension	37
7. SEWING	40
7-1. Before starting sewing....	40
7-2. Sewing operation	40
8. MAINTENANCE AND INSPECTION	42
8-1. Checking the needle	42
8-2. Cleaning the rotary hook	42
8-3. Lubrication	43
8-4. Draining the oil	44
8-5. Cleaning the control box air inlet port	44
8-6. Cleaning the air holes of belt cover and frame side cover	44
8-7. Cleaning the eye guard	44
9. STANDARD ADJUSTMENTS	45
9-1. Adjusting the needle bar height	45
9-2. Adjusting the needle bar lift amount	45
9-3. Adjusting the driver needle guard	46
9-4. Adjusting the needle clearance	46
9-5. Adjusting the shuttle race thread guide	46
9-6. Adjusting the thread take-up amount	47
9-7. Adjusting the movable knife	48
9-8. Adjusting the work clamp lift amount	50
9-9. Work clamp adjustment	51
9-10. Changing the work clamp lift	51
9-11. Work clamp interchangeability	52
9-12. Adjusting the needle up stop position	52
9-13. Adjusting the thread wiper	53
9-14. Adjustment of air pressure	53
9-15. Checking the input sensor and DIP switch input	54
9-16. Checking the input voltage	55
9-17. Clearing all memory settings	55
10. DIP SWITCH	56
10-1. Panel DIP switch functions	56
10-2. DIP switches inside the control box	57
11. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES	58
12. SETTING THE WORK CLAMP MODE	62
12-1. Light work clamp	63
13. TABLE OF ERROR CODES	64
14. GAUGE PARTS LIST ACCORDING TO SUBCLASSES	66
15. TROUBLESHOOTING	69
16. OPTIONAL PARTS	72