Canon imageFORMULA DR-2010M Workgroup Scanner User Manual - Page 24

Placing Documents, Feeding in the Separation Mode

Get Canon imageFORMULA DR-2010M Workgroup Scanner PDF manuals and user guides View all Canon imageFORMULA DR-2010M Workgroup Scanner manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Contents Back Previous Page Next Page 3. Placing Documents There are two methods for feeding documents, the Page Separation mode and Bypass mode. Feeding pages continuously from a stack of documents placed in the feed tray is called the Page Separation mode. Feeding documents one sheet at a time or feeding documents consisting of multiple pages that are attached, is called the bypass mode. The document feed method can be changed by moving the feed selection lever. 3 Fan the pages of the document to be scanned, and shift them so that the top of the first page (the bottom of the front of the document) is the lowest. (Place the document so that the top of the document is facing down.) Feeding in the Page Separation Mode 1 Switch the feed selection lever to (Page Separation). CAUTION When placing documents into the feed tray, take care not to cut your hands on the edges of the paper. 4 Place the document with the reverse side facing you, and the top of the document facing down. 2 Adjust the document guides to fit the width of the document to be scanned. Insert the document with the reverse side facing you IMPORTANT There is a load limit mark ( ) on the document guides. Do not stack documents higher than this mark (approximately 50 sheets of 20 lb bond (80 g/m2) paper.) Doing so may cause a paper jam. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Back
Previous Page
Next Page
Contents
24
3. Placing Documents
There are two methods for feeding documents, the Page Separation mode and
Bypass mode. Feeding pages continuously from a stack of documents placed in
the feed tray is called the Page Separation mode. Feeding documents one sheet
at a time or feeding documents consisting of multiple pages that are attached, is
called the bypass mode.
The document feed method can be changed by moving the feed selection lever.
1
Switch the feed selection lever to
(Page Separation).
2
Adjust the document guides to fit the width of the document to be scanned.
3
Fan the pages of the document to be scanned, and shift them so that the
top of the first page (the bottom of the front of the document) is the lowest.
(Place the document so that the top of the document is facing down.)
CAUTION
When placing documents into the feed tray, take care not to cut your hands on
the edges of the paper.
4
Place the document with the reverse side facing you, and the top of the
document facing down.
IMPORTANT
There is a load limit mark (
) on the document guides. Do not stack
documents higher than this mark (approximately 50 sheets of 20 lb bond
(80 g/m
2
) paper.) Doing so may cause a paper jam.
Feeding in the Page Separation Mode
Insert the document with
the reverse side facing you