Dell B2360DN Mono Laser User Guide - Page 65

Network Card menu, TCP/IP menu, Network/Ports, Standard Network, Network [x], Network [x] Setup

Page 65 highlights

Understanding the printer menus 65 Network Card menu To access the menu, navigate to either of the following: • Network/Ports > Standard Network > Standard Network Setup > Network Card • Network/Ports > Network [x] > Network [x] Setup > Network Card Use To View Card Status Connected Disconnected View the connection status of the network card. View Card Speed View the speed of an active network card. Network Address UAA LAA View the network addresses. Job Timeout 0-255 seconds Set the amount of time it takes for a network print job to be canceled. Notes: • 90 seconds is the factory default setting. • A setting value of 0 disables the timeout. • If a value of 1-9 is selected, then the setting is saved as 10. TCP/IP menu To access the menu, navigate to any of the following: • Network/Ports > Standard Network > Standard Network Setup > TCP/IP • Network/Ports > Network [x] > Network [x] Setup > TCP/IP Note: This menu is available only in network printers or printers connected to print servers. Use To Set Hostname Set the host name. Notes: • This setting can be changed only from the Embedded Web Server. • The host name can be up to 15 characters and can be a US‑ASCII or alphanumeric character, or hyphen. IP Address View or change the current TCP/IP address. Note: Manually setting the IP address sets the "Enable DHCP" and "Enable Auto IP" settings to Off. It also sets "Enable BOOTP" and "Enable RARP" to Off on systems that support BOOTP and RARP. Netmask Gateway View or change the current TCP/IP netmask. View or change the current TCP/IP gateway. Enable DHCP On Off Specify the DHCP address and parameter assignment. Note: On is the factory default setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158

Network Card menu
To access the menu, navigate to either of the following:
Network/Ports
>
Standard Network
>
Standard Network Setup
>
Network Card
Network/Ports
>
Network [x]
>
Network [x] Setup
>
Network Card
Use
To
View Card Status
Connected
Disconnected
View the connection status of the network card.
View Card Speed
View the speed of an active network card.
Network Address
UAA
LAA
View the network addresses.
Job Timeout
0–255 seconds
Set the amount of time it takes for a network print job to be canceled.
Notes:
90 seconds is the factory default setting.
A setting value of 0 disables the timeout.
If a value of 1–9 is selected, then the setting is saved as 10.
TCP/IP menu
To access the menu, navigate to any of the following:
Network/Ports
>
Standard Network
>
Standard Network Setup
>
TCP/IP
Network/Ports
>
Network [x]
>
Network [x] Setup
>
TCP/IP
Note:
This menu is available only in network printers or printers connected to print servers.
Use
To
Set Hostname
Set the host name.
Notes:
This setting can be changed only from the Embedded Web Server.
The host name can be up to 15 characters and can be a US
ASCII or
alphanumeric character, or hyphen.
IP Address
View or change the current TCP/IP address.
Note:
Manually setting the IP address sets the “Enable DHCP” and “Enable Auto IP”
settings to Off. It also sets “Enable BOOTP” and “Enable RARP” to Off on systems
that support BOOTP and RARP.
Netmask
View or change the current TCP/IP netmask.
Gateway
View or change the current TCP/IP gateway.
Enable DHCP
On
Off
Specify the DHCP address and parameter assignment.
Note:
On is the factory default setting.
Understanding the printer menus
65