Dell PowerConnect 6248 Configuration Guide - Page 42

Interfaces Enabled for IGMP Snooping, Total Packets Received Without Errors

Get Dell PowerConnect 6248 PDF manuals and user guides View all Dell PowerConnect 6248 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

9. View information about the IGMP snooping configuration. console#show ip igmp snooping Admin Mode Enable Multicast Control Frame Count 0 Interfaces Enabled for IGMP Snooping........... None Vlans enabled for IGMP snooping 100 In this example, Host A sends a join message for group 225.1.1.1. Host B sends a join message for group 225.1.1.2. Because IGMP snooping is enabled on the switch and on VLAN 100, the switch listens to the messages and dynamically adds ports 1/g5 and 1/g10 to the multicast address table. Port 1/g15 did not send a join message, so it does not appear in the table, as the following show command indicates. console#show bridge multicast address-table Vlan MAC Address Type Ports 100 0100.5E01.0101 Dynamic 1/g5 100 0100.5E01.0102 Dynamic 1/g10 Forbidden ports for multicast addresses: Vlan MAC Address Ports 100 0100.5E01.0101 100 0100.5E01.0102 When the video server sends multicast data to group 225.1.1.1, port 1/g5 participates and receives multicast traffic, but port 1/g10 does not participate because it is a member of a different multicast group. Without IGMP snooping, all ports that are members of VLAN 100 would be flooded with traffic for all multicast groups, which would greatly increase the amount of traffic on the switch. You can use the show statistics command to view information about the multicast data transmitted or received by each interface. The following output shows a portion of the command output for interfaces 1/g5 and 1/g10. In this example, the counters were cleared before the video server began transmitting data. console#show statistics ethernet 1/g5 ... Total Packets Received Without Errors.......... 626494 Unicast Packets Received 0 42 Switching Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
42
Switching Configuration
9.
View information about the IGMP snooping configuration.
console#show ip igmp snooping
Admin Mode
.....................................
Enable
Multicast Control Frame Count
..................
0
Interfaces Enabled for IGMP Snooping
...........
None
Vlans enabled for IGMP snooping
................
100
In this example, Host A sends a join message for group 225.1.1.1. Host B sends a join message for group
225.1.1.2. Because IGMP snooping is enabled on the switch and on VLAN 100, the switch listens to the
messages and dynamically adds ports 1/g5 and 1/g10 to the multicast address table. Port 1/g15 did not
send a join message, so it does not appear in the table, as the following
show
command indicates.
console#show bridge multicast address-table
Vlan
MAC Address
Type
Ports
----
-----------------------
-------
-----------------
100
0100.5E01.0101
Dynamic
1/g5
100
0100.5E01.0102
Dynamic
1/g10
Forbidden ports for multicast addresses:
Vlan
MAC Address
Ports
----
-----------------------
----------------------
100
0100.5E01.0101
100
0100.5E01.0102
When the video server sends multicast data to group 225.1.1.1, port 1/g5 participates and receives
multicast traffic, but port 1/g10 does not participate because it is a member of a different multicast
group. Without IGMP snooping, all ports that are members of VLAN 100 would be flooded with traffic
for all multicast groups, which would greatly increase the amount of traffic on the switch.
You can use the show statistics command to view information about the multicast data transmitted or
received by each interface. The following output shows a portion of the command output for interfaces
1/g5 and 1/g10. In this example, the counters were cleared before the video server began transmitting
data.
console#show statistics ethernet 1/g5
...
Total Packets Received Without Errors
..........
626494
Unicast Packets Received
.......................
0