Dell PowerConnect 6248 Configuration Guide - Page 94

Using the Web Interface to Con RIP, Routing > RIP > Interface Configuration.

Get Dell PowerConnect 6248 PDF manuals and user guides View all Dell PowerConnect 6248 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Example #3. Enable RIP for the Switch The next sequence enables RIP for the switch. The route preference defaults to 15. console#config router rip enable exit exit Example #4. Enable RIP for the VLAN Routing Interfaces This command sequence enables RIP for VLAN 2 and VLAN 3. Authentication defaults to none, and no default route entry is created. The commands specify that both interfaces receive both RIP-1 and RIP-2 frames, but send only RIP-2 formatted frames. console#config interface vlan 2 ip rip ip rip receive version both ip rip send version rip2 exit interface vlan 3 ip rip ip rip receive version both ip rip send version rip2 exit exit Using the Web Interface to Configure RIP Use the following screens to perform the same configuration using the Graphical User Interface: • Routing > IP > Configuration> To enable routing for the switch. • Routing > IP > Interface Configuration > To configure the VLAN routing interfaces. • Routing > RIP > Configuration. To enable RIP for the switch. • Routing > RIP > Interface Configuration. To enable RIP for the VLAN routing interfaces and specify the RIP versions. 94 Routing Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
94
Routing Configuration
Example #3. Enable RIP for the Switch
The next sequence enables RIP for the switch. The route preference defaults to 15.
console#config
router rip
enable
exit
exit
Example #4. Enable RIP for the VLAN Routing Interfaces
This command sequence enables RIP for VLAN 2 and VLAN 3. Authentication defaults to none, and no
default route entry is created. The commands specify that both interfaces receive both RIP-1 and RIP-2
frames, but send only RIP-2 formatted frames.
console#config
interface vlan 2
ip rip
ip rip receive version both
ip rip send version rip2
exit
interface vlan 3
ip rip
ip rip receive version both
ip rip send version rip2
exit
exit
Using the Web Interface to Configure RIP
Use the following screens to perform the same configuration using the Graphical User Interface:
•
Routing > IP > Configuration>
To enable routing for the switch.
•
Routing > IP > Interface Configuration
> To configure the VLAN routing interfaces.
•
Routing > RIP > Configuration.
To enable RIP for the switch.
•
Routing > RIP > Interface Configuration.
To enable RIP for the VLAN routing interfaces and specify
the RIP versions.