HP 6125G HP 6125G & 6125G/XG Blade Switches ACL and QoS Command Refere - Page 99

Burst function configuration commands, burst-mode enable

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Burst function configuration commands burst-mode enable Syntax burst-mode enable View undo burst-mode enable System view Default level 2: System level Parameters None Description Use burst-mode enable to enable the burst function. Use undo burst-mode enable to disable the burst function. By default, the burst function is disabled. The burst function improves packet buffering and forwarding performance in the following scenarios: • Dense broadcast or multicast traffic and massive burst traffic are present. • High-speed traffic is forwarded over a low-speed link or traffic received from multiple interfaces at the same speed is forwarded through an interface at the same speed. By enabling the burst function on your switch, you can improve the processing performance of the switch operating in these scenarios and reduce packet loss rate. Examples # Enable the burst function. system-view [Sysname] burst-mode enable 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
94
Burst function configuration commands
burst-mode enable
Syntax
burst-mode enable
undo burst-mode enable
View
System view
Default level
2: System level
Parameters
None
Description
Use
burst-mode enable
to enable the burst function.
Use
undo burst-mode enable
to disable the burst function.
By default, the burst function is disabled.
The burst function improves packet buffering and forwarding performance in the following scenarios:
•
Dense broadcast or multicast traffic and massive burst traffic are present.
•
High-speed traffic is forwarded over a low-speed link or traffic received from multiple interfaces at
the same speed is forwarded through an interface at the same speed.
By enabling the burst function on your switch, you can improve the processing performance of the switch
operating in these scenarios and reduce packet loss rate.
Examples
# Enable the burst function.
<Sysname> system-view
[Sysname] burst-mode enable