HP 6310 User Guide - Page 108

Contact HP, Solution, I connected the USB cable, but I am having problems using the HP All-in-One

Page 108 highlights

One to turn on. If you press the On button again during this time, you might turn the device off. Warning If the HP All-in-One still does not turn on, it might have a mechanical failure. Unplug the HP All-in-One from the power outlet and contact HP. Go to: www.hp.com/support If prompted, choose your country/region, and then click Contact HP for information on calling for technical support. I connected the USB cable, but I am having problems using the HP All-in-One with my computer Solution You must first install the software that came with the HP All-in-One before connecting the USB cable. During installation, do not plug in the USB cable until prompted by the onscreen instructions. Connecting the USB cable before prompted can cause errors. Once you have installed the software, connecting your computer to the HP All-inOne with a USB cable is straightforward. Simply plug one end of the USB cable into the back of your computer and the other into the back of the HP All-in-One. You can connect to any USB port on the back of your computer. Troubleshooting For more information on installing the software and connecting the USB cable, see the Setup Guide that came with the HP All-in-One. I received a message on the display to attach the control panel faceplate Solution This might mean the control panel faceplate is not attached, or it is attached incorrectly. Make sure to align the faceplate over the buttons on the top of the HP All-in-One and snap it firmly into place. User Guide 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167

One to turn on. If you press the
On
button again during this time, you might turn
the device off.
Warning
If the HP All-in-One still does not turn on, it might have a
mechanical failure. Unplug the HP All-in-One from the power outlet and
contact HP. Go to:
www.hp.com/support
If prompted, choose your country/region, and then click
Contact HP
for
information on calling for technical support.
I connected the USB cable, but I am having problems using the HP All-in-One
with my computer
Solution
You must first install the software that came with the HP All-in-One
before connecting the USB cable. During installation, do not plug in the USB
cable until prompted by the onscreen instructions. Connecting the USB cable
before prompted can cause errors.
Once you have installed the software, connecting your computer to the HP All-in-
One with a USB cable is straightforward. Simply plug one end of the USB cable
into the back of your computer and the other into the back of the HP All-in-One.
You can connect to any USB port on the back of your computer.
For more information on installing the software and connecting the USB cable,
see the Setup Guide that came with the HP All-in-One.
I received a message on the display to attach the control panel faceplate
Solution
This might mean the control panel faceplate is not attached, or it is
attached incorrectly. Make sure to align the faceplate over the buttons on the top
of the HP All-in-One and snap it firmly into place.
User Guide
105
Troubleshooting