Home » HP Manuals » Storage Devices » HP Cisco MDS 9020 » Manual Viewer

HP Cisco MDS 9020 Cisco MDS 9500 Series Hardware Installation Guide (OL-17467- - Page 156

Installing a CompactFlash Card, Removing and Installing Clock Modules

Add to My Manuals
Save this manual to your list of manuals

Page 156 highlights

Removing and Installing Clock Modules Chapter 2 Installing the Cisco MDS 9500 Series Send documentation comments to [email protected]. Installing a CompactFlash Card To install a CompactFlash card, follow these steps: Step 1 Step 2 Position the CompactFlash card with the connector end of the card toward the slot. The connector end of the card is on the opposite side of the write-protection switch. Insert the card into the slot until the card is firmly seated in the connector at the back of the slot and the ejector button pops out toward you. Caution The card does not insert all the way inside the slot; a portion of the card remains outside the slot. Do not attempt to force the card past this point or you could damage the connector pins. Removing and Installing Clock Modules The Cisco MDS 9500 Series includes one or more clock modules that are accessible from the back of the chassis. In the unlikely event of a clock module failure, Cisco recommends that the failed clock module be replaced during a maintenance window. The Cisco MDS 9513 and 9509 Directors have two field-replacable clock modules. The Cisco MDS 9506 Director has one field-replacable clock module. A separate procedure is provided for each type of director: • Removing a Clock Module from the Cisco MDS 9513 Director, page 2-77 • Installing a Clock Module into the Cisco MDS 9513 Director, page 2-79 • Removing a Clock Module from the Cisco MDS 9509 Director, page 2-80 • Installing a Clock Module into the Cisco MDS 9509 Director, page 2-83 • Removing a Clock Module from the Cisco MDS 9506 Director, page 2-83 • Installing a Clock Module into the Cisco MDS 9506 Director, page 2-86 Before installing the clock module, check the contents of your kit. Table 2-5 lists the contents of the clock module replacement kit, part number DS-C9513-CL. Table 2-5 Contents of Cisco MDS 9513 Clock Module Replacement Kits Quantity 1 1 Part Description Cisco MDS 9513 clock module Disposable ESD wrist strap These tools are required to remove or install a clock module: • Number 2 Phillips screwdriver • Your own ESD-prevention equipment or the disposable grounding wrist strap included with all upgrade kits, field-replaceable units (FRUs), and spares 2-76 Cisco MDS 9500 Series Hardware Installation Guide OL-17467-02

Section	Page
Cisco MDS 9500 Series Hardware Installation Guide	1
Contents	3
New and Changed Information	11
Preface	17
Audience	17
Organization	17
Conventions	18
Related Documentation	20
Release Notes	20
Compatibility Information	20
Regulatory Compliance and Safety Information	20
Hardware Installation	20
Cisco Fabric Manager	21
Command-Line Interface	21
Intelligent Storage Networking Services Configuration Guides	21
Troubleshooting and Reference	21
Installation and Configuration Note	21
Obtaining Documentation, Obtaining Support, and Security Guidelines	22
Product Overview	23
Chassis	24
Cisco MDS 9513 Director	25
Cisco MDS 9509 Director	28
Cisco MDS 9506 Director	29
Backplane and Clock Modules	30
Cisco MDS Fibre Channel Switch for IBM Blade Center	31
Power Supplies	31
Cisco MDS 9513 Power Supplies	32
Cisco MDS 9509 Power Supplies	34
Cisco MDS 9506 Power Supplies	37
Fan Modules	38
Supervisor Modules	38
Supervisor-2 Modules	39
Control and Management	40
Processor	40
Port Interfaces	40
LEDs on the Supervisor-2 Module	41
Supervisor-1 Modules	43
Control and Management	43
Crossbar Switching Fabric	44
Processor	44
Port Interfaces	44
LEDs on the Supervisor-1 Module	45
Crossbar Modules	47
Cisco MDS 9000 Series Module Compatibility	49
Port Index Availability	50
Switching Modules	54
48-port 8-Gbps Fibre Channel Switching Module	55
24-port 8-Gbps Fibre Channel Switching Module	55
4/44-port 8-Gbps Host-Optimized Fibre Channel Switching Module	55
48-Port 4-Gbps Fibre Channel Switching Module	56
24-port 4-Gbps Fibre Channel Switching Module	57
12-port 4-Gbps Fibre Channel Switching Module	57
4-port 10-Gbps Fibre Channel Switching Module	58
LEDs on the Generation 2 Switching Modules	59
32-Port 2-Gbps Fibre Channel Switching Module	59
16-Port 2-Gbps Fibre Channel Switching Module	60
Switching Module Features	61
LEDs on the Generation 1 Switching Module	62
Services Modules	63
18/4-Port Multiservice Module	63
18/4-Port Multiservice Federal Information Processing Standards Module	64
LEDs on the 18/4-Port Multiservice Module	65
14/2-Port Multiprotocol Services Module	66
LEDs on the MPS-14/2 Module	67
IP Storage Services Modules	68
LEDs on IP Storage Services Modules	69
32-Port Fibre Channel Advanced Services Module	70
LEDs on the Fibre Channel Advanced Services Modules	71
32-Port Fibre Channel Storage Services Module	72
LEDs on the Storage Services Modules	73
Caching Services Module	74
LEDs on the Caching Services Module	76
Supported Transceivers	77
X2 Transceivers	77
Fibre Channel SFP Transceivers	78
Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	78
CWDM Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	78
Gigabit Ethernet SFP Transceivers	78
DWDM Fibre Channel SFP Transceivers	79
Installing the Cisco MDS 9500 Series	81
Preinstallation	82
Installation Options	82
Installation Guidelines	83
Required Equipment	85
Unpacking and Inspecting the Switch	85
Installing the Chassis in a Cabinet or Rack	86
Installing the Cisco MDS 9513 Director in a Rack	87
Installing the Cisco MDS 9509 Director in a Rack	91
Installing the Cisco MDS 9506 Director in a Rack	95
System Grounding	97
Proper Grounding Practices	97
Preventing Electrostatic Discharge Damage	99
Establishing the System Ground	102
Required Tools and Equipment	102
Grounding the Chassis	103
Starting Up the Switch	108
Connecting the Power Supplies	108
Providing Power to an AC Power Supply for the Cisco MDS 9513 Director	109
Providing Power to an AC Power Supply for the Cisco MDS 9509 and Cisco MDS 9506 Directors	110
Providing Power to a DC Power Supply in the Cisco MDS 9509 Director	113
Providing Power to a DC Power Supply in the Cisco MDS 9506 Director	114
Powering Up the Switch and Verifying Component Installation	116
Removing, Installing, and Verifying Supervisor, Switching, and Services Modules	118
Removing Supervisor Modules	119
Installing Supervisor Modules	120
Removing a Caching Services Module	124
Removing Other Switching and Services Modules	125
Installing a Switching or Services Module, Including Caching Services Modules	125
Verifying Installation of Supervisor, Switching, and Services Modules	126
Removing and Installing a Crossbar Module	127
Maintaining a Caching Services Module	130
Maintaining the Batteries on the Caching Services Module	130
Maintaining the Disk Drives on the Caching Services Module	131
Removing and Installing a Power Supply or PEM	131
Removing and Installing the Power Supplies on the Cisco MDS 9513 Director	132
Removing an AC Power Supply from the Cisco MDS 9513 Director	132
Installing an AC Power Supply in the Cisco MDS 9513 Director	134
Removing an AC Power Supply from the Cisco MDS 9509 Director	136
Installing an AC Power Supply in the Cisco MDS 9509 Director	137
Removing a DC Power Supply from the Cisco MDS 9509 Director	141
Installing a DC Power Supply in the Cisco MDS 9509 Director	142
Removing and Installing the PEMs on the Cisco MDS 9506 Director	144
Removing an AC PEM	144
Removing a DC PEM	144
Installing an AC PEM	146
Installing a DC PEM	146
Removing an AC or DC Power Supply from the Cisco MDS 9506 Director	147
Installing an AC or DC Power Supply in the Cisco MDS 9506 Director	147
Removing and Installing Fan Modules	148
Removing a Front Fan Module on the Cisco MDS 9513 Director	149
Installing a Front Fan Module on the Cisco MDS 9513 Director	150
Removing the Crossbar Module Fan Tray	151
Installing the Crossbar Module Fan Tray	152
Removing a Front Fan Module on the Cisco MDS 9509 Director	153
Installing a Front Fan Module on the Cisco MDS 9509 Director	153
Removing a Front Fan Module on the Cisco MDS 9506 Director	154
Installing a Front Fan Module on the Cisco MDS 9506 Director	154
Removing and Installing CompactFlash Cards	155
Removing a CompactFlash Card	155
Installing a CompactFlash Card	156
Removing and Installing Clock Modules	156
Removing a Clock Module from the Cisco MDS 9513 Director	157
Installing a Clock Module into the Cisco MDS 9513 Director	159
Removing a Clock Module from the Cisco MDS 9509 Director	160
Installing a Clock Module into the Cisco MDS 9509 Director	163
Removing a Clock Module from the Cisco MDS 9506 Director	163
Installing a Clock Module into the Cisco MDS 9506 Director	166
Migrating to Generation 3 8-Gbps Fibre Channel Switching Modules	167
Overview	167
Usage Guidelines	168
Before You Begin Upgrading the MDS 9513 Director	169
Migration Procedures for the MDS 9513 Director	169
Installing the MDS 9000 4/44-Port 8-Gbps Host-Optimized Module	169
Installing MDS 9513 Fabric 2 Modules and Running Cisco SAN-OS 3.x	171
Installing MDS 9513 Fabric 2 Modules and Installing MDS 9000 24-port or 48-port 8-Gbps Modules	175
Installing the MDS 9513 Fabric 2 Modules and Activating Higher Bandwidth by Reloading the Switch	176
Installing the MDS 9513 Fabric 2 Modules and Activating Higher Bandwidth by Powering Down the Switch	177
Migration Procedure for the MDS 9509 Director and MDS 9506 Director	178
Connecting the Cisco MDS 9500 Series	181
Preparing for Network Connections	182
Connecting to the Console Port	182
Connecting to the COM1 Port	184
Connecting to the MGMT 10/100/1000 Ethernet Port	186
Connecting to the MGMT 10/100 Ethernet Port	187
Connecting to a Fibre Channel Port	189
Removing and Installing X2 Transceivers	189
Removing an X2 Transceiver	191
Installing an X2 Transceiver	191
Removing and Installing SFP Transceivers	192
Removing an SFP Transceiver	192
Installing an SFP Transceiver	194
Removing and Installing Cables into SFP Transceivers	194
Removing a Cable from an SFP Transceiver	194
Installing a Cable into an SFP Transceiver	195
Maintaining SFP Transceivers and Fiber-Optic Cables	196
Cabinet and Rack Installation	197
Cabinet and Rack Requirements	197
General Requirements for Cabinets and Racks	197
Cabinet and Rack Requirements for the Cisco MDS 9513 Chassis	198
Cabinet and Rack Requirements for the Cisco MDS 9509 and Cisco MDS 9506 Chassis	198
Requirements Specific to Perforated Cabinets	199
Perforated Cabinet Requirements for the Cisco MDS 9513 Chassis	199
Perforated Cabinet Requirements for the Cisco MDS 9509 and the Cisco MDS 9506 Chassis	199
Requirements Specific to Solid-Walled Cabinets	200
Solid-Walled Cabinet Requirements for the Cisco MDS 9513 Chassis	200
Solid-Walled Cabinet Requirements for the Cisco MDS 9509 and the Cisco MDS 9506 Chassis	201
Requirements Specific to Standard Open Racks	201
Requirements Specific to Two-Post Telco Racks	202
Cisco MDS 9000 Family Telco and EIA Shelf Bracket	202
Rack-Mounting Guidelines	203
Before Installing the Rack-Mount Support Brackets	203
Before Installing the Shelf Brackets	204
Required Equipment	204
Installing the Shelf Bracket Kit into a Two-Post Telco Rack	205
Installing the Shelf Bracket Kit into a Four-Post EIA Rack	206
Installing the Switch on the Rack-Mount Support Brackets	207
Installing the Switch on the Shelf Brackets	208
Removing the Shelf Bracket Kit (Optional)	208
Cisco MDS 9500 Shelf Bracket	209
Rack-Mounting Guidelines	210
Before Installing the Shelf Brackets	210
Required Equipment	210
Installing the Cisco MDS 9500 Shelf Bracket Kit into a Cabinet or Rack	211
Installing the Switch on the Shelf Brackets	212
Technical Specifications	213
Switch Specifications	213
Module Specifications	216
Weight of Modules	217
Power Specifications for the Cisco MDS 9513 Director	218
Specifications for the Cisco MDS 9513 Power Supplies	218
Component Power Requirements and Heat Dissipation for the Cisco MDS 9513 Director	219
AC Power Consumption for the Cisco MDS 9513 Director	220
Power Specifications for the Cisco MDS 9509 Director	221
Specifications for the Cisco MDS 9509 Power Supplies	221
Component Power Requirements and Heat Dissipation for the Cisco MDS 9509 Director	223
AC Power Consumption for the Cisco MDS 9509 Director	226
Power Specifications for the Cisco MDS 9506 Director	226
Specifications for the Cisco MDS 9506 Power Supplies	227
Component Power Requirements and Heat Dissipation for the Cisco MDS 9506 Director	228
AC Power Consumption for the Cisco MDS 9506 Director	231
X2 Transceiver Specifications	231
Cisco 10-Gbps Fibre Channel X2 Transceivers	232
General Specification for Cisco 10-Gbps Fibre Channel X2 Transceivers	232
Environmental Conditions and Power Requirement Specifications for Cisco 10-Gbps Fibre Channel X2 Transceivers	232
Cisco 10-Gbps Ethernet X2 Transceivers	233
General Specification for Cisco 10-Gbps Ethernet X2 Transceivers	233
Environmental and Power Requirements Specifications for Cisco 10-Gbps Ethernet X2 Transceiver	234
Cisco 10-Gbps Ethernet DWDM X2 Transceiver	234
SFP and SFP+ Transceiver Specifications	234
Cisco Fibre Channel SFP and SFP+ Transceivers	235
General Specifications for Cisco 8-Gbps Fibre Channel SFP+ Transceivers	236
Environmental and Power Requirements for Cisco 8-Gbps Fibre Channel SFP+ Transceivers	236
General Specifications for Cisco 4-Gbps Fibre Channel SFP Transceivers	238
Environmental and Power Requirement for Cisco 4-Gbps Fibre Channel SFP Transceivers	238
General Specifications for Cisco 2-Gbps Fibre Channel SFP Transceivers	239
Environmental and Power Requirement for Cisco 2-Gbps Fibre Channel SFP Transceivers	239
Maximum Environmental and Electrical Ratings for Cisco Fibre Channel SFP Transceivers	240
Cisco Fibre Channel and Gigabit Ethernet Transceivers	240
General Specifications for Cisco Fibre Channel and Gigabit Ethernet SFP Transceivers	241
Environmental and Power Requirement Specifications for Cisco Fibre Channel and Gigabit Ethernet SFP Transceivers	241
Cisco CWDM SFP Transceivers	242
Environmental and Optical Specifications for Cisco 2-Gbps CWDM SFP Transceivers	243
Environmental and Optical Specifications for Cisco 4-Gbps CWDM SFP Transceivers	245
Cisco Gigabit Ethernet Transceivers	246
General Specifications for Cisco Gigabit Ethernet Transceivers	246
Environmental and Power Requirement Specifications for Cisco Gigabit Ethernet Transceivers	246
Cisco DWDM SFP Transceivers	246
Cable and Port Specifications	249
Cables and Adapters Provided	249
Console Port	250
Console Port Pinouts	250
Connecting the Console Port to a Computer Using the DB-25 Adapter	250
Connecting the Console Port to a Computer Using the DB-9 Adapter	251
COM1 Port	251
COM1 Port Pinouts	251
Connecting the COM1 Port to a Modem	252
MGMT 10/100/1000 Ethernet Port	252
MGMT 10/100 Ethernet Port	254
Supported Power Cords and Plugs	255
Power Cords	255
Supported Plugs for 6000-W AC, 2500-W AC, and 1900-W AC Power Supplies	257
Supported Plugs for the 4000-W AC Power Supply	259
Jumper Power Cord	259
Power Supply AC Power Cords	260
AC Power Cord Illustrations	261
Site Planning and Maintenance Records	265
Contacting Customer Service	265
Finding the Chassis Serial Number	266
Site Preparation Checklist	268
Contact and Site Information	270
Chassis and Module Information	271

Match case Limit results 1 per page

Send documentation comments to [email protected].

2-76

Cisco MDS 9500 Series Hardware Installation Guide

OL-17467-02

Chapter 2

Installing the Cisco MDS 9500 Series

Removing and Installing Clock Modules

Installing a CompactFlash Card

To install a CompactFlash card, follow these steps:

Step 1

Position the CompactFlash card with the connector end of the card toward the slot. The connector end

of the card is on the opposite side of the write-protection switch.

Step 2

Insert the card into the slot until the card is firmly seated in the connector at the back of the slot and the

ejector button pops out toward you.

Caution

The card does not insert all the way inside the slot; a portion of the card remains outside the

slot. Do not attempt to force the card past this point or you could damage the connector pins.

Removing and Installing Clock Modules

The Cisco MDS 9500 Series includes one or more clock modules that are accessible from the back of

the chassis. In the unlikely event of a clock module failure, Cisco recommends that the failed clock

module be replaced during a maintenance window. The Cisco MDS 9513 and 9509 Directors have two

field-replacable clock modules. The Cisco MDS 9506 Director has one field-replacable clock module.

A separate procedure is provided for each type of director:

•

Removing a Clock Module from the Cisco MDS 9513 Director, page 2-77

•

Installing a Clock Module into the Cisco MDS 9513 Director, page 2-79

•

Removing a Clock Module from the Cisco MDS 9509 Director, page 2-80

•

Installing a Clock Module into the Cisco MDS 9509 Director, page 2-83

•

Removing a Clock Module from the Cisco MDS 9506 Director, page 2-83

•

Installing a Clock Module into the Cisco MDS 9506 Director, page 2-86

Before installing the clock module, check the contents of your kit.

Table 2-5

lists the contents of the

clock module replacement kit, part number DS-C9513-CL.

These tools are required to remove or install a clock module:

•

Number 2 Phillips screwdriver

•

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all

upgrade kits, field-replaceable units (FRUs), and spares

Table 2-5

Contents of Cisco MDS 9513 Clock Module Replacement Kits

Quantity

Part Description

Cisco MDS 9513 clock module

Disposable ESD wrist strap