HP Integrity Superdome SX1000 Windows Integrity Management Agents Reference - Page 23
Error in a fabric Port Probable Cause: Reset. SNMP Trap: hpevtFabricPortError - 5404
View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
Event ID Event Severity Event Description 5365 Error The current cell detected incompatible CPUs on another cell Probable Cause: Mixed CPU types are installed in the same partition. Remove them. SNMP Trap: hpevtPdIncompatibleCpuTypes - 5365 in HPIFPTRAP.MIB. 5366 Error Current cell was too slow creating the local rendezvous set Probable Cause: Cell too slow. Could be bad hardware. Check for other errors and reset. Recommended Action: If assistance is required, contact the HP Support Center. SNMP Trap: hpevtPdCellLateLocalRendezSet - 5366 in HPIFPTRAP.MIB. 5376 Error Reporting cell was not included in the global cell set Probable Cause: Fabric problem, Connection problem or timing problem. Reset the PD. SNMP Trap: hpevtCellNotInGlobalSet - 5376 in HPIFPTRAP.MIB. 5380 Error No Core Cell can be selected in the PD. Probable Cause: No cells have a functioning core IO card. Add a core IO card to a cell in the PD and reset. SNMP Trap: hpevtNoViableCoreCellInPd - 5380 in HPIFPTRAP.MIB. 5383 Error Firmware was unable to notify utilities of the core cell number Probable Cause: Communication with utilities is broken. Check for earlier errors or NVRAM problems. SNMP Trap: hpevtErrorPromotingCoreCell - 5383 in HPIFPTRAP.MIB. 5403 Error Fabric code unable to find a needed service provider. Probable Cause: The registry is corrupt or the ROM is incomplete. SNMP Trap: hpevtFabricNoServiceProviders 5403 in HPIFPTRAP.MIB. 5404 Warning Error in a fabric Port Probable Cause: Reset. SNMP Trap: hpevtFabricPortError - 5404 in HPIFPTRAP.MIB. 5405 Warning Parity error detected on read from fabric Probable Cause: Hardware problem. Check connections and reset. SNMP Trap: hpevtFabricReadError - 5405 in HPIFPTRAP.MIB. 5406 Warning Error writing to Fabric Probable Cause: Bad hardware. SNMP Trap: hpevtFabricWriteError - 5406 in HPIFPTRAP.MIB. 5407 Error Crossbar slices are out of rev with each other. Probable Cause: Bad hardware configuration, different revisions of crossbars are installed. Recommended Action: Check crossbar revisions and ensure all installed crossbar revisions are the same. Replace the crossbar that is not in rev with the others. SNMP Trap: hpevtXbcSlicesHwVersionDiffer - 5407 in HPIFPTRAP.MIB. 5408 Error Crossbar slices are configured poorly Probable Cause: Fatal configuration. Reconfigure the hardware. SNMP Trap: hpevtXbcSlicesInDiffLocation - 5408 in HPIFPTRAP.MIB. 5411 Error A CPU has taken over for the monarch CPU Probable Cause: The previous monarch may be suspect. SNMP Trap: hpevtMonarchTakeover - 5411 in HPIFPTRAP.MIB. 5416 Error Sram cannot be used on the cell Probable Cause: SRAM cannot be located or used on the cell board. Replace the cell board. SNMP Trap: hpevtDeadSram - 5416 in HPIFPTRAP.MIB. 5417 Error The dillon hardware cannot be located. Probable Cause: ROM is corrupt. Replace the rom or reprogram flash. SNMP Trap: hpevtDeadDillon - 5417 in HPIFPTRAP.MIB. 5418 Error A required piece of PDH bus hardware cannot be contacted. Probable Cause: Verify all connections of PDH bus components or replace the cell board. SNMP Trap: hpevtDeadPdhHw - 5418 in HPIFPTRAP.MIB. 5419 Warning Error: PCI Buses are configured for multiple speeds Probable Cause: A PCI card is configured with mixed speeds. Recommended Action: Correct the configuration problem. SNMP Trap: hpevtIoPciBusMixedSpeeds - 5419 in HPIFPTRAP.MIB. 5420 Error The bus depth was exceeded during IO probing. Probable Cause: Too many PCI bridge cards are configured in single PCI segment mode. Recommended Action: Reconfigure PCI cards and remove some of the bridge devices. SNMP Trap: hpevtIoPciBusDepthExceeded - 5420 in HPIFPTRAP.MIB. Platform Agent Events 23