HP Integrity Superdome SX1000 Windows Integrity Management Agents Reference - Page 84

Unable to write to an XBC port ROUTE_TABLE_ENABLE_MASK CSR in Arches

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Event ID Event Severity Event Description 10833 Warning Firmware error setting the NVRAM value of preferred-bsp for the vPars monitor. The partition will boot using the PD monarch, but the value of preferred-bsp may not match this CPU. Probable Cause: Firmware could not store to the NVRAM holding the EFI preferred-bsp variable Recommended Action: Reset the server, restore factory default NVRAM and reconfigure soft partitions. SNMP Trap: hpevtFWErrSetNvramVal - 10833 in HPIFPTRAP.MIB. 10842 Warning Unable to write to an XBC port ROUTE_TABLE_ENABLE_MASK CSR in Arches Fabric Phase3. Data field: (XBC port 48) | (XBC ID 32) | (route). Probable Cause: System firmware was unable to write a fabric hardware register. Recommended Action: Capture IPMI event logs, look for additional errors. Contact your HP Support Representative to analyze the fabric SNMP Trap: hpevtUnablWrtXbcPrtRoutTblEnblMsk - 10842 in HPIFPTRAP.MIB. 10853 Error An unrecoverable processor interrupt occurred. IPF firmware owned the processor interrupt vector table (IVT) at the time of the interrupt. Probable Cause: Probable bug in System Firmware, EFI driver, EFI app or OS loader (prior to OS launch). The event data field contains the IVT offset applicable to the interrupt. See table 5-7 (Interruption Vector Table) in the Intel ASDM Volume 2. Recommended Action: Provide console log containing register dump to HP Customer Engineer. SNMP Trap: hpevtProcessIntrptUnRecoverble - 10853 in HPIFPTRAP.MIB. 10871 Error SBA call to LBA SetDeviceMask method fails. Probable Cause: SBA call to LBA SetDeviceMask method fails. Recommended Action: Disable rope in non-mca path, error exit in MCA path. SNMP Trap: hpevtSBASetDevMaskFail - 10871 in HPIFPTRAP.MIB. 10927 Error LBA slot device scan error. Probable Cause: The LBA component detected a card in a PCI slot, but got no response from config register requests to the card. Recommended Action: Reseat or replace the PCI card. SNMP Trap: hpevtLBASlotDevScanErr - 10927 in HPIFPTRAP.MIB. 10936 Warning There is none (or inadequate) memory slice resource assigned to the fPar so it cannot boot its instance. The fPar will be disabled (enter a spinloop) because it cannot boot, or if in vPars mode will return control to the monitor. Probable Cause: There is no Memory owned by the soft partition (fPar) whose CPU emitted this event. Recommended Action: Reconfigure the soft partition containing the CPU that emitted this event and be sure to give memory resources to that soft partition before reset of that partition. Until doing so, this soft partition will be unbootable and emit this event on each attempt. SNMP Trap: hpevtInadequateMemTofPar - 10936 in HPIFPTRAP.MIB. 10937 Warning Couldn't collect vertex information during Fabric Info call. Data Field: return status. Probable Cause: There was a problem while collecting a list of fabric link info. Recommended Action: Look for additional IPMI event logs. Contact your HP Support Representative to analyze the fabric. SNMP Trap: hpevtFailCollVertxInfo - 10937 in HPIFPTRAP.MIB. 10938 Warning Couldn't collect the vertices during the Fabric Info call. Data Field: number of vertices returned. Probable Cause: An invalid number of fabric vertices was found while collecting fabric information. Recommended Action: Fabric information cannot be reported properly. Collect IPMI Event logs and contact your HP Support Representative. SNMP Trap: hpevtFailCollVertxFabInfoCall - 10938 in HPIFPTRAP.MIB. 10939 Warning Couldn't find all the edges during a procedure call. Data Field: return status. Probable Cause: There was a problem while collecting a list of fabric link info. Recommended Action: Look for additional IPMI event logs. Contact your HP Support Representative to analyze the fabric. SNMP Trap: hpevtFailFndEdgeProcCall - 10939 in HPIFPTRAP.MIB. 10940 Warning Couldn't find an appropriate number of edges during a procedure call. Data Field: the number of edges found. Probable Cause: There was a problem while collecting a list of fabric link info. Recommended Action: Look for additional IPMI event logs. Contact your HP Support Representative to analyze the fabric. SNMP Trap: hpevtFailFndEdgProcCall - 10940 in HPIFPTRAP.MIB. 84 Management Agents Event Tables

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Event Description
Event Severity
Event ID
Firmware error setting the NVRAM value of preferred-bsp for the vPars monitor.
The partition will boot using the PD monarch, but the value of preferred-bsp may
not match this CPU. Probable Cause: Firmware could not store to the NVRAM holding
the EFI preferred-bsp variable Recommended Action: Reset the server, restore factory
default NVRAM and reconfigure soft partitions. SNMP Trap:
hpevtFWErrSetNvramVal - 10833 in HPIFPTRAP.MIB.
Warning
10833
Unable to write to an XBC port ROUTE_TABLE_ENABLE_MASK CSR in Arches
Fabric Phase3. Data field: (XBC port 48) | (XBC ID 32) | (route). Probable Cause:
System firmware was unable to write a fabric hardware register. Recommended
Action: Capture IPMI event logs, look for additional errors. Contact your HP Support
Representative to analyze the fabric SNMP Trap:
hpevtUnablWrtXbcPrtRoutTblEnblMsk - 10842 in HPIFPTRAP.MIB.
Warning
10842
An unrecoverable processor interrupt occurred. IPF firmware owned the processor
interrupt vector table (IVT) at the time of the interrupt. Probable Cause: Probable
bug in System Firmware, EFI driver, EFI app or OS loader (prior to OS launch). The
event data field contains the IVT offset applicable to the interrupt. See table 5-7
(Interruption Vector Table) in the Intel ASDM Volume 2. Recommended Action:
Provide console log containing register dump to HP Customer Engineer. SNMP Trap:
hpevtProcessIntrptUnRecoverble - 10853 in HPIFPTRAP.MIB.
Error
10853
SBA call to LBA SetDeviceMask method fails. Probable Cause: SBA call to LBA
SetDeviceMask method fails. Recommended Action: Disable rope in non-mca path,
error exit in MCA path. SNMP Trap: hpevtSBASetDevMaskFail - 10871 in
HPIFPTRAP.MIB.
Error
10871
LBA slot device scan error. Probable Cause: The LBA component detected a card in
a PCI slot, but got no response from config register requests to the card. Recommended
Action: Reseat or replace the PCI card. SNMP Trap: hpevtLBASlotDevScanErr - 10927
in HPIFPTRAP.MIB.
Error
10927
There is none (or inadequate) memory slice resource assigned to the fPar so it cannot
boot its instance. The fPar will be disabled (enter a spinloop) because it cannot boot,
or if in vPars mode will return control to the monitor. Probable Cause: There is no
Memory owned by the soft partition (fPar) whose CPU emitted this event.
Recommended Action: Reconfigure the soft partition containing the CPU that emitted
this event and be sure to give memory resources to that soft partition before reset of
that partition. Until doing so, this soft partition will be unbootable and emit this
event on each attempt. SNMP Trap: hpevtInadequateMemTofPar - 10936 in
HPIFPTRAP.MIB.
Warning
10936
Couldn't collect vertex information during Fabric Info call. Data Field: return status.
Probable Cause: There was a problem while collecting a list of fabric link info.
Recommended Action: Look for additional IPMI event logs. Contact your HP Support
Representative to analyze the fabric. SNMP Trap: hpevtFailCollVertxInfo - 10937 in
HPIFPTRAP.MIB.
Warning
10937
Couldn't collect the vertices during the Fabric Info call. Data Field: number of vertices
returned. Probable Cause: An invalid number of fabric vertices was found while
collecting fabric information. Recommended Action: Fabric information cannot be
reported properly. Collect IPMI Event logs and contact your HP Support
Representative. SNMP Trap: hpevtFailCollVertxFabInfoCall - 10938 in
HPIFPTRAP.MIB.
Warning
10938
Couldn't find all the edges during a procedure call. Data Field: return status. Probable
Cause: There was a problem while collecting a list of fabric link info. Recommended
Action: Look for additional IPMI event logs. Contact your HP Support Representative
to analyze the fabric. SNMP Trap: hpevtFailFndEdgeProcCall - 10939 in
HPIFPTRAP.MIB.
Warning
10939
Couldn't find an appropriate number of edges during a procedure call. Data Field:
the number of edges found. Probable Cause: There was a problem while collecting
a list of fabric link info. Recommended Action: Look for additional IPMI event logs.
Contact your HP Support Representative to analyze the fabric. SNMP Trap:
hpevtFailFndEdgProcCall - 10940 in HPIFPTRAP.MIB.
Warning
10940
84
Management Agents Event Tables