HP Integrity Superdome SX2000 Windows Integrity Management Agents Reference - Page 49

Data read from the CC Error Mask CSR Probable Cause: CC to XBC link init failure.

Get HP Integrity Superdome SX2000 PDF manuals and user guides View all HP Integrity Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Event ID Event Severity Event Description 8154 Warning EFI unable to read initial debug level from the BMC Probable Cause: SAL service to read tokens not functioning properly. Recommended Action: Reset the system. Clear SFW NVM. Upgrade system firmware. SNMP Trap: hpevtEfiDebugLevelTokenErr - 8154 in HPIFPTRAP.MIB. 8156 Error A XBC port was unexpectedly found to not be landmined. Probable Cause: An XBC is indicating a port failure Recommended Action: Validate all of the cells connectivity to the PD Check the XBC chips seating reset the system replace either cells/system backplane SNMP Trap: hpevtXbcPortNotLandmined - 8156 in HPIFPTRAP.MIB. 8159 Error An invalid number of XBC ports were landmined in the system. Probable Cause: Hardware failure: link, crossbar chip, or cell. Recommended Action: Check for hardware failures. Reset backplane to re-initialize fabric. SNMP Trap: hpevtFabricValidateError - 8159 in HPIFPTRAP.MIB. 8184 Error The backplane was not recognized as one that contains fabric Probable Cause: An unrecognized backplane is installed. Recommended Action: Contact HP Support Personnel to determine why the backplane was unrecognized. SNMP Trap: hpevtFabricISRInvalidBkp - 8184 in HPIFPTRAP.MIB. 8186 Warning Writing the XIN Error Mask Register to zero failed Probable Cause: CC Write Failure. Recommended Action: Contact HP Support personnel to analyze the fabric. SNMP Trap: hpevtFabricXinWrZeroErrMaskError - 8186 in HPIFPTRAP.MIB. 8187 Error Dumping error info. Read status of the Primary Mode Register Probable Cause: CC to XBC link init failure. Contact your HP service representative to check the CC to XBC link SNMP Trap: hpevtFabricCcPriModeRegRdStatus - 8187 in HPIFPTRAP.MIB. 8188 Error Data read from the CC Primary Mode CSR Probable Cause: CC to XBC link init failure. Contact your HP service representative to check the CC to XBC link SNMP Trap: hpevtFabricCcPriModeRegRdData - 8188 in HPIFPTRAP.MIB. 8189 Error Dumping error info. Read status of the CC Error Mask Register Probable Cause: CC to XBC link init failure. Contact your HP service representative to check the CC to XBC link SNMP Trap: hpevtFabricCcErrMaskRegRdStatus - 8189 in HPIFPTRAP.MIB. 8190 Error Data read from the CC Error Mask CSR Probable Cause: CC to XBC link init failure. Contact your HP service representative to check the CC to XBC link SNMP Trap: hpevtFabricCcErrMaskRegRdData - 8190 in HPIFPTRAP.MIB. 8194 Warning The link could not be crossed upon first attempt Probable Cause: The neighbor port is not routable. The port is either: not connected, landmined, in FE, or contains an SBE or LPE. Recommended Action: Contact HP Support personnel to analyze the fabric. SNMP Trap: hpevtFabricXingNeighborPortBad - 8194 in HPIFPTRAP.MIB. 8195 Error Failed reading an XBC forward progress register Probable Cause: Fabric access error Recommended Action: Contact HP Support personnel to analyze the fabric. SNMP Trap: hpevtFabricISRRdFwdProgErr - 8195 in HPIFPTRAP.MIB. 8198 Error Could not find an adjacent XBC due to broken fabric links Probable Cause: Possible crossbar failure Recommended Action: Contact HP Support personnel to analyze the crossbar. SNMP Trap: hpevtFabricGetNeighborMaxLinksBroken - 8198 in HPIFPTRAP.MIB. 8199 Warning The run-time verification of a programming assumption has failed. Probable Cause: Hardware in unknown state, or programming bug found. Recommended Action: Upgrade PM firmware to latest revision. If already at current revision, replace UGUY board. SNMP Trap: hpevtPmAssertionFailed - 8199 in HPIFPTRAP.MIB. 8200 Warning An unknown error has been detected by the PDHC firmware. Probable Cause: Hardware in unknown state, or programming bug found. Recommended Action: Upgrade PM firmware to latest revision. If already at current revision, replace UGUY board. SNMP Trap: hpevtPmFirmwareUnknownErr - 8200 in HPIFPTRAP.MIB. 8202 Error Data field contains data meant for firmware debug only. Probable Cause: Debug event. Recommended Action: Contact your hp support representative. SNMP Trap: hpevtPmCriticalDebug - 8202 in HPIFPTRAP.MIB. Platform Agent Events 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Event Description
Event Severity
Event ID
EFI unable to read initial debug level from the BMC Probable Cause: SAL service to
read tokens not functioning properly. Recommended Action: Reset the system. Clear
SFW NVM. Upgrade system firmware. SNMP Trap: hpevtEfiDebugLevelTokenErr
- 8154 in HPIFPTRAP.MIB.
Warning
8154
A XBC port was unexpectedly found to not be landmined. Probable Cause: An XBC
is indicating a port failure Recommended Action: Validate all of the cells connectivity
to the PD Check the XBC chips seating reset the system replace either cells/system
backplane SNMP Trap: hpevtXbcPortNotLandmined - 8156 in HPIFPTRAP.MIB.
Error
8156
An invalid number of XBC ports were landmined in the system. Probable Cause:
Hardware failure: link, crossbar chip, or cell. Recommended Action: Check for
hardware failures. Reset backplane to re-initialize fabric. SNMP Trap:
hpevtFabricValidateError - 8159 in HPIFPTRAP.MIB.
Error
8159
The backplane was not recognized as one that contains fabric Probable Cause: An
unrecognized backplane is installed. Recommended Action: Contact HP Support
Personnel to determine why the backplane was unrecognized. SNMP Trap:
hpevtFabricISRInvalidBkp - 8184 in HPIFPTRAP.MIB.
Error
8184
Writing the XIN Error Mask Register to zero failed Probable Cause: CC Write Failure.
Recommended Action: Contact HP Support personnel to analyze the fabric. SNMP
Trap: hpevtFabricXinWrZeroErrMaskError - 8186 in HPIFPTRAP.MIB.
Warning
8186
Dumping error info. Read status of the Primary Mode Register Probable Cause: CC
to XBC link init failure. Contact your HP service representative to check the CC to
XBC link SNMP Trap: hpevtFabricCcPriModeRegRdStatus- 8187 in HPIFPTRAP.MIB.
Error
8187
Data read from the CC Primary Mode CSR Probable Cause: CC to XBC link init
failure. Contact your HP service representative to check the CC to XBC link SNMP
Trap: hpevtFabricCcPriModeRegRdData - 8188 in HPIFPTRAP.MIB.
Error
8188
Dumping error info. Read status of the CC Error Mask Register Probable Cause: CC
to XBC link init failure. Contact your HP service representative to check the CC to
XBC link SNMP Trap: hpevtFabricCcErrMaskRegRdStatus- 8189 in HPIFPTRAP.MIB.
Error
8189
Data read from the CC Error Mask CSR Probable Cause: CC to XBC link init failure.
Contact your HP service representative to check the CC to XBC link SNMP Trap:
hpevtFabricCcErrMaskRegRdData - 8190 in HPIFPTRAP.MIB.
Error
8190
The link could not be crossed upon first attempt Probable Cause: The neighbor port
is not routable. The port is either: not connected, landmined, in FE, or contains an
SBE or LPE. Recommended Action: Contact HP Support personnel to analyze the
fabric. SNMP Trap: hpevtFabricXingNeighborPortBad - 8194 in HPIFPTRAP.MIB.
Warning
8194
Failed reading an XBC forward progress register Probable Cause: Fabric access error
Recommended Action: Contact HP Support personnel to analyze the fabric. SNMP
Trap: hpevtFabricISRRdFwdProgErr - 8195 in HPIFPTRAP.MIB.
Error
8195
Could not find an adjacent XBC due to broken fabric links Probable Cause: Possible
crossbar failure Recommended Action: Contact HP Support personnel to analyze
the crossbar. SNMP Trap: hpevtFabricGetNeighborMaxLinksBroken - 8198 in
HPIFPTRAP.MIB.
Error
8198
The run-time verification of a programming assumption has failed. Probable Cause:
Hardware in unknown state, or programming bug found. Recommended Action:
Upgrade PM firmware to latest revision. If already at current revision, replace UGUY
board. SNMP Trap: hpevtPmAssertionFailed - 8199 in HPIFPTRAP.MIB.
Warning
8199
An unknown error has been detected by the PDHC firmware. Probable Cause:
Hardware in unknown state, or programming bug found. Recommended Action:
Upgrade PM firmware to latest revision. If already at current revision, replace UGUY
board. SNMP Trap: hpevtPmFirmwareUnknownErr - 8200 in HPIFPTRAP.MIB.
Warning
8200
Data field contains data meant for firmware debug only. Probable Cause: Debug
event. Recommended Action: Contact your hp support representative. SNMP Trap:
hpevtPmCriticalDebug - 8202 in HPIFPTRAP.MIB.
Error
8202
Platform Agent Events
49