HP P3410A HP NetRAID 1M/2M Installation & Configuration - Page 111

Run View/Add/Delete Configuration option

Get HP P3410A - NetRAID 1M RAID Controller PDF manuals and user guides
UPC - 725184582783
View all HP P3410A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Chapter 8 Upgrading to an HP NetRAID-1M or HP NetRAID-2M Adapter 2. Install the new adapter, as described in Step D of Chapter 5, "Installation and Configuration." If you are installing an HP NetRAID-2M adapter, be sure to plug in the Battery Backup Unit first (see Figure 8-3, above). 3. Connect all SCSI cables to the new adapter, as described in Step E of Chapter 5, "Installation and Configuration." 4. Close the HP Netserver panel or replace the HP Netserver cover, plug in the power cord(s), and turn on power to the HP Netserver. 5. After you see the flashing message "Firmware Initializing," you will see this message: Configuration of NVRAM and drives mismatch for Host Adapter X Run View/Add/Delete Configuration option of Configuration Utility Press any key to enter the Configuration Utility. This message tells you that the configuration information stored in the drives (the correct configuration) does not match the configuration information stored in NVRAM on the newly installed HP NetRAID-1M or 2M adapter. NOTE If there is more than one HP NetRAID adapter (including any integrated HP NetRAID controller), the message tells you which adapter number has the mismatch. Be sure to note which adapter needs to be reconfigured. 6. Press any key and the HP NetRAID Express Tools utility starts automatically. You see the Tools Management menu. 7. If you have more than one HP NetRAID-1M or 2M adapter (including any integrated HP NetRAID controller), do the following to select the adapter you have just installed: a. Choose Select Adapter from the Tools Management menu. b. Choose the adapter with the mismatched configuration. 8. Choose Configure from the Tools Management menu. 9. Choose View/Add/Delete from the Configure menu. 10. Choose Disk, as opposed to NVRAM, from the View/Add/Delete menu. 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Chapter 8
Upgrading to an HP NetRAID-1M or HP NetRAID-2M Adapter
103
2.
Install the new adapter, as described in Step D of Chapter 5, "Installation
and Configuration." If you are installing an HP NetRAID-2M adapter, be
sure to plug in the Battery Backup Unit first (see Figure 8-3, above).
3.
Connect all SCSI cables to the new adapter, as described in Step E of
Chapter 5, "Installation and Configuration."
4.
Close the HP Netserver panel or replace the HP Netserver cover, plug in
the power cord(s), and turn on power to the HP Netserver.
5.
After you see the flashing message "
Firmware Initializing
," you
will see this message:
Configuration of NVRAM and drives mismatch for
Host Adapter
X
Run View/Add/Delete Configuration option of
Configuration Utility
Press any key to enter the Configuration Utility.
This message tells you that the configuration information stored in the drives
(the correct configuration) does not match the configuration information stored
in NVRAM on the newly installed HP NetRAID-1M or 2M adapter.
NOTE
If there is more than one HP NetRAID
adapter (including any
integrated HP NetRAID controller), the message tells you
which adapter number has the mismatch. Be sure to note
which adapter needs to be reconfigured.
6.
Press any key and the HP NetRAID Express Tools utility starts
automatically. You see the Tools Management menu.
7.
If you have more than one HP NetRAID-1M or 2M adapter (including any
integrated HP NetRAID controller), do the following to select the adapter
you have just installed:
a.
Choose
Select Adapter
from the Tools Management menu.
b.
Choose the adapter with the mismatched configuration.
8.
Choose
Configure
from the Tools Management menu.
9.
Choose
View/Add/Delete
from the Configure menu.
10.
Choose
Disk
, as opposed to NVRAM, from the View/Add/Delete menu.