HP P3410A HP NetRAID 1M/2M Installation & Configuration - Page 136

Changing the Battery Backup Unit, Connecting the Battery Backup Unit

Get HP P3410A - NetRAID 1M RAID Controller PDF manuals and user guides
UPC - 725184582783
View all HP P3410A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

Chapter 11 HP NetRAID-2M Battery Backup Unit 2. Choose Objects from the Tools Management menu. 3. Choose Battery Backup to view the battery status. To Check Battery Status with HP NetRAID Config 1. Start HP NetRAID Config. 2. Choose Objects from the Management menu. 3. Choose Battery Backup to view the battery status. Warnings That Battery Needs Replacement • Power-up diagnostics include a battery life check. An on-screen message alerts you if the battery life is low. • HP NetRAID sends an SNMP error message that alerts you of the condition. Changing the Battery Backup Unit Do not attempt to install a new Battery Backup Unit. If the battery needs to be changed, call an HP Service Representative. Connecting the Battery Backup Unit The HP NetRAID-2M adapter is shipped with the Battery Backup Unit installed and charged, but disconnected. Follow the directions below to connect the Battery Backup Unit. CAUTION When the Battery Backup Unit is connected: • Do not place the HP NetRAID-2M adapter on a conductive surface. • When installing the adapter, do not allow the adapter or its Battery Backup Unit to touch any part of the HP Netserver. Doing so could short the battery, and it may damage other components. You may place the adapter on an antistatic mat. The Battery Backup Unit is a battery pack already installed on the HP NetRAID-2M adapter. To connect the battery pack, plug the connector 128

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Chapter 11
HP NetRAID-2M Battery Backup Unit
128
2.
Choose
Objects
from the Tools Management menu.
3.
Choose
Battery Backup
to view the battery status.
To Check Battery Status with HP NetRAID Config
1.
Start HP NetRAID Config.
2.
Choose
Objects
from the Management menu.
3.
Choose
Battery Backup
to view the battery status.
Warnings That Battery Needs Replacement
•
Power-up diagnostics include a battery life check. An on-screen message
alerts you if the battery life is low.
•
HP NetRAID sends an SNMP error message that alerts you of the
condition.
Changing the Battery Backup Unit
Do not attempt to install a new Battery Backup Unit. If the battery needs to be
changed, call an HP Service Representative.
Connecting the Battery Backup Unit
The HP NetRAID-2M adapter is shipped with the Battery Backup Unit installed
and charged, but disconnected. Follow the directions below to connect the Battery
Backup Unit.
CAUTION
When the Battery Backup Unit is connected:
•
Do
not
place the HP NetRAID-2M adapter on a
conductive surface.
•
When installing the adapter, do
not
allow the adapter or
its Battery Backup Unit to touch any part of the
HP Netserver. Doing so could short the battery, and it may
damage other components. You may place the adapter on
an antistatic mat.
The Battery Backup Unit is a battery pack already installed on the
HP NetRAID-2M adapter. To connect the battery pack, plug the connector