HP P3410A HP NetRAID 1M/2M Installation & Configuration - Page 54

Step F., Start HP Netserver Navigator to Launch, HP NetRAID Assistant

Get HP P3410A - NetRAID 1M RAID Controller PDF manuals and user guides
UPC - 725184582783
View all HP P3410A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 5 Installation and Configuration CAUTION Handle disk modules carefully. They are more susceptible to shock, vibration, and electrostatic discharge when they are not in the cabinet. When removing a module while the system is powered on, disengage the module and wait for it to stop spinning before removing it from its hot-swap slot. Also, do not touch the SCSI edge connector pins. The oils on your skin could impair the electrical connection. Replace Cover If you removed the power supplies or fans, replace them according to the instructions in your HP Netserver documentation. Close or replace the panels or covers on the computer and reconnect the HP Netserver to power and networks. Step F. Start HP Netserver Navigator to Launch HP NetRAID Assistant Boot HP Netserver Navigator CD-ROM To launch the HP NetRAID Assistant, you must start from the HP Netserver Navigator CD-ROM. Ensure that all the SCSI devices power up before or at the same time as the host computer. NOTE HP NetRAID-1M and 2M adapters do not support bootable CD-ROM drives or tape drives. Boot Messages If you receive an error message during the boot process, refer to Chapter 14, "Troubleshooting," or to the online help in Information Assistant for more information. Some power-up (boot) messages are routine. Select Disk Array Controller Configuration If HP Navigator asks you to set the date, time, and so on, do so. The HP Netserver Navigator Main Menu then appears. 1. When the HP Netserver Navigator Main Menu is displayed, choose Configure the Server. 2. Choose Custom Setup from the next group of choices. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Chapter 5
Installation and Configuration
46
CAUTION
Handle disk modules carefully. They are more susceptible to
shock, vibration, and electrostatic discharge when they are
not in the cabinet. When removing a module while the system
is powered on, disengage the module and wait for it to stop
spinning before removing it from its hot-swap slot.
Also, do not touch the SCSI edge connector pins. The oils on
your skin could impair the electrical connection.
Replace Cover
If you removed the power supplies or fans, replace them according to the
instructions in your HP Netserver documentation.
Close or replace the panels or covers on the computer and reconnect the
HP Netserver to power and networks.
Step F.
Start HP Netserver Navigator to Launch
HP NetRAID Assistant
Boot HP Netserver Navigator CD-ROM
To launch the HP NetRAID Assistant, you must start from the
HP
Netserver
Navigator CD-ROM
. Ensure that all the SCSI devices power up before or at the
same time as the host computer.
NOTE
HP NetRAID-1M and 2M adapters do not support bootable
CD-ROM drives or tape drives.
Boot Messages
If you receive an error message during the boot process, refer to Chapter 14,
"Troubleshooting," or to the online help in Information Assistant for more
information. Some power-up (boot) messages are routine.
Select Disk Array Controller Configuration
If HP Navigator asks you to set the date, time, and so on, do so. The
HP Netserver Navigator Main Menu then appears.
1.
When the HP Netserver Navigator Main Menu is displayed, choose
Configure the Server
.
2.
Choose
Custom Setup
from the next group of choices.