HP Photosmart 3200 User Guide - Page 44

Wired (802.3) network settings, Parameter, Description - offline

Get HP Photosmart 3200 - All-in-One Printer PDF manuals and user guides View all HP Photosmart 3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

General network settings The following table describes the general network settings shown on the network configuration page. Parameter Description Network Status Status of the HP All-in-One: ● Ready: The HP All-in-One is ready to receive or transmit data. ● Offline: The HP All-in-One is not currently connected to the network. Active connection type Network mode of the HP All-in-One: ● Wired: The HP All-in-One is connected by Ethernet cable to an IEEE 802.3 network. ● None: There is no network connection. URL The IP address of the Embedded Web Server. Note You will need to know this URL when you try to access the Embedded Web Server. Firmware Revision The internal networking component and device firmware revision code. Note If you call HP Support, depending on the problem, you might be asked to provide the firmware revision code. Hostname The TCP/IP name assigned by the installation software to the device. By default, this is the letters HP followed by the last 6 digits of the Media Access Control (MAC) address. Admin Password Status of the administrator's password for the Embedded Web Server: ● Set: Password is specified. You must enter the password to make changes to the Embedded Web Server parameters. ● Not Set: No password is set. A password is not required for making changes to the Embedded Web Server parameters. mDNS Rendezvous is used with local and ad hoc networks that don't use central DNS servers. To perform name services, Rendezvous uses a DNS alternative called mDNS. With mDNS, your computer can find and use any HP All-in-One connected to your local area network. It can also work with any other Ethernet-enabled device that appears on the network. Wired (802.3) network settings The following table describes the 802.3 wired settings shown on the network configuration page. Network setup User Guide 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
General network settings
The following table describes the general network settings shown on the network
configuration page.
Parameter
Description
Network Status
Status of the HP All-in-One:
●
Ready
: The HP All-in-One is ready to receive or transmit data.
●
Offline
: The HP All-in-One is not currently connected to the
network.
Active
connection type
Network mode of the HP All-in-One:
●
Wired
: The HP All-in-One is connected by Ethernet cable to
an IEEE 802.3 network.
●
None
: There is no network connection.
URL
The IP address of the Embedded Web Server.
Note
You will need to know this URL when you try to access the
Embedded Web Server.
Firmware
Revision
The internal networking component and device firmware revision
code.
Note
If you call HP Support, depending on the problem, you
might be asked to provide the firmware revision code.
Hostname
The TCP/IP name assigned by the installation software to the
device. By default, this is the letters HP followed by the last 6
digits of the Media Access Control (MAC) address.
Admin
Password
Status of the administrator's password for the Embedded Web
Server:
●
Set
: Password is specified. You must enter the password to
make changes to the Embedded Web Server parameters.
●
Not Set
: No password is set. A password is not required for
making changes to the Embedded Web Server parameters.
mDNS
Rendezvous is used with local and ad hoc networks that don't use
central DNS servers. To perform name services, Rendezvous
uses a DNS alternative called mDNS.
With mDNS, your computer can find and use any HP All-in-One
connected to your local area network. It can also work with any
other Ethernet-enabled device that appears on the network.
Wired (802.3) network settings
The following table describes the 802.3 wired settings shown on the network
configuration page.
User Guide
41
Network setup