HP ProLiant DL288 HP ProLiant DL288 G6 Server Software Configuration Guide - Page 41

POST error indicators, Recoverable POST errors

Get HP ProLiant DL288 PDF manuals and user guides View all HP ProLiant DL288 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

hardware failures are accurately isolated during POST. The number of tests displayed depends on the configuration of the server. During POST you can: • Press ESC to skip the HP logo and go to POST boot progress display system summary screen. • Press F10 to access the Setup Utility. • Press F12 to request a network boot (PXE). • Press F1 to continue POST after POST errors are detected. POST error indicators When POST detects a system failure it displays a POST error message. Recoverable POST errors When a non-fatal error occurs during POST, the screen will display an error message with the format "xxx-Error Identifier String" where "xxx" is a unique number code that matches ODM system specific error documentation and may be a hexadecimal or decimal value. All Error messages describe the problems as shown below: Table 23 POST Error Messages Error code Description 10 Floppy Controller Failure 00B CMOS Memory Size Wrong 00C RAM R/W test failed 003 CMOS Battery Low 005 CMOS Checksum Bad 040 Refresh timer test failed 041 Display memory test failed 048 Password check failed 120 $A0CCMOS Cleared by Jumper. Restore the Jumper and Continue... 122 $A0CPassword Cleared By Jumper. Restore the Jumper and Continue... 150 Processor failed BIST 160 Processor missing microcode: 192 L3 cache size mismatch 193 CPUID, Processor stepping are different 194 CPUID, Processor family are different 195 Front side bus mismatch. System halted. 196 CPUID, Processor Model are different 197 Processor speeds mismatched System BIOS configuration 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
System BIOS configuration 41
hardware failures are accurately isolated during POST. The number of tests displayed depends on the
configuration of the server.
During POST you can:
•
Press
ESC
to skip the HP logo and go to POST boot progress display system summary screen.
•
Press
F10
to access the Setup Utility.
•
Press
F12
to request a network boot (PXE).
•
Press
F1
to continue POST after POST errors are detected.
POST error indicators
When POST detects a system failure it displays a POST error message.
Recoverable POST errors
When a non-fatal error occurs during POST, the screen will display an error message with the format
“xxx-Error Identifier String” where “xxx” is a unique number code that matches ODM system specific
error documentation and may be a hexadecimal or decimal value.
All Error messages describe the problems as shown below:
Table 23
POST Error Messages
Error code
Description
10
Floppy Controller Failure
00B
CMOS Memory Size Wrong
00C
RAM R/W test failed
003
CMOS Battery Low
005
CMOS Checksum Bad
040
Refresh timer test failed
041
Display memory test failed
048
Password check failed
120
$A0CCMOS Cleared by Jumper.
Restore the Jumper and Continue…
122
$A0CPassword Cleared By Jumper.
Restore the Jumper and Continue…
150
Processor failed BIST
160
Processor missing microcode:
192
L3 cache size mismatch
193
CPUID, Processor stepping are different
194
CPUID, Processor family are different
195
Front side bus mismatch. System halted.
196
CPUID, Processor Model are different
197
Processor speeds mismatched