HP ProLiant DL288 HP ProLiant DL288 G6 Server Software Configuration Guide - Page 43

Perform the post-installation procedure described

Get HP ProLiant DL288 PDF manuals and user guides View all HP ProLiant DL288 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

• All memory modules are properly installed. • If you have installed a PCI accessory board, verify that the board is firmly seated and any jumpers on the board are properly set. Refer to the documentation provided with the accessory board. • All internal cabling and connections are in their proper order. • If you have changed the jumper on the system board, verify that each is properly set. If the POST failure occurs after installing an accessory, perform the following steps: 1. Perform the pre-installation procedure described on page 45. 2. If necessary, remove any expansion boards, assemblies, or cables that prevent access to the system components. 3. Check the following conditions: a. If you have installed an expansion board, verify that the board is firmly seated in its slot and any switches or jumpers on the board are properly set. Refer to the documentation provided with the expansion board. b. All internal cabling and connections are in their proper order. c. If you have changed any jumper block on the system board, verify that each one is properly set. 4. Perform the post-installation procedure described on page 46. 5. Turn on the monitor. 6. If the server still does not work, repeat step 2. 7. Remove all accessories, except the primary boot hard disk drive. 8. Repeat steps 4 and 5. If the server now works, replace the boards and accessories one at a time to determine which one is causing the problem. System BIOS configuration 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
System BIOS configuration 43
•
All memory modules are properly installed.
•
If you have installed a PCI accessory board, verify that the board is firmly seated and any
jumpers on the board are properly set. Refer to the documentation provided with the accessory
board.
•
All internal cabling and connections are in their proper order.
•
If you have changed the jumper on the system board, verify that each is properly set.
If the POST failure occurs after installing an accessory, perform the following steps:
1.
Perform the pre-installation procedure described on page 45.
2.
If necessary, remove any expansion boards, assemblies, or cables that prevent access to the
system components.
3.
Check the following conditions:
a.
If you have installed an expansion board, verify that the board is firmly seated in its slot and
any switches or jumpers on the board are properly set. Refer to the documentation provided
with the expansion board.
b.
All internal cabling and connections are in their proper order.
c.
If you have changed any jumper block on the system board, verify that each one is properly
set.
4.
Perform the post-installation procedure described on page 46.
5.
Turn on the monitor.
6.
If the server still does not work, repeat step 2.
7.
Remove all accessories, except the primary boot hard disk drive.
8.
Repeat steps 4 and 5.
If the server now works, replace the boards and accessories one at a time to determine which
one is causing the problem.