HP StorageWorks MSA 2/8 HP StorageWorks MSA SAN Switch 2/8 Installation Guide - Page 27

Installing an SFP Module, Insert the SFP into the port until it is firmly seated and the latching

Get HP StorageWorks MSA 2/8 - SAN Switch PDF manuals and user guides View all HP StorageWorks MSA 2/8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installing the MSA SAN Switch 2/8 Installing an SFP Module Use these steps to connect the SFPs in the ports of the MSA SAN Switch, as required. 1. Remove the shipping plugs from the appropriate ports on the switch panel. 2. Position the SFP so the key (the tab near the cable-end of the SFP) is on top. 3. Insert the SFP into the port until it is firmly seated and the latching mechanism clicks. Note: The SFP is keyed so that it can only be inserted with the correct orientation into the port. If the SFP does not slide in easily, check the orientation. See Figure 7 for an illustration of the fiber cable, the SFP module and tab, and the optical port. 3 2 1 Figure 7: Installing an SFP Note: To remove an SFP from an optical port, carefully grasp the tab at the top of the SFP and pull the module straight out of the port. Do not pull up on the tab; you may damage your SFP module. MSA SAN Switch 2/8 Installation Guide 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Installing the MSA SAN Switch 2/8
27
MSA SAN Switch 2/8 Installation Guide
Installing an SFP Module
Use these steps to connect the SFPs in the ports of the MSA SAN Switch, as
required.
1.
Remove the shipping plugs from the appropriate ports on the switch panel.
2.
Position the SFP so the key (the tab near the cable-end of the SFP) is on top.
3.
Insert the SFP into the port until it is firmly seated and the latching
mechanism clicks.
Note:
The SFP is keyed so that it can only be inserted with the correct orientation into
the port. If the SFP does not slide in easily, check the orientation.
See Figure 7 for an illustration of the fiber cable, the SFP module and tab, and
the optical port.
Figure 7:
Installing an SFP
Note:
To remove an SFP from an optical port, carefully grasp the tab at the top of the
SFP and pull the module
straight out of the port
.
Do not pull up on the tab; you may damage your SFP module.
3
1
2