HP StorageWorks MSA 2/8 HP StorageWorks MSA SAN Switch 2/8 Installation Guide - Page 67

C: I/O Connection Specifications

Get HP StorageWorks MSA 2/8 - SAN Switch PDF manuals and user guides View all HP StorageWorks MSA 2/8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

I/O Connection Specifications C This appendix covers the following topics: ■ The serial port can be used to connect the switch to a computer workstation to configure the switch IP address without connecting to the fabric. The serial port's parameters are 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control., page 67 ■ Ethernet Port Specifications, page 68 The serial port can be used to connect the switch to a computer workstation to configure the switch IP address without connecting to the fabric. The serial port's parameters are 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. The port requires a straight serial cable with a female 9-pin subminiature-D connector. Only pins 2, 3, and 5 are supported, as shown in Table 8. Table 8: Serial Port Cabling Pin Layout Pin Signal Description 1 NC 2 TX Transmit data 3 RX Receive data 4 NC 5 GND Ground 6 NC 7 NC 8 NC 9 NC Note: For dust and ESD (electrostatic discharge) protection, a cover is provided for the serial port and should be kept on the port whenever the serial port is not in use. MSA SAN Switch 2/8 Installation Guide 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
67
MSA SAN Switch 2/8 Installation Guide
C
I/O Connection Specifications
This appendix covers the following topics:
■
The serial port can be used to connect the switch to a computer workstation to
configure the switch IP address without connecting to the fabric. The serial
port’s parameters are 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow
control.
, page 67
■
Ethernet Port Specifications
, page 68
The serial port can be used to connect the switch to a computer workstation to
configure the switch IP address without connecting to the fabric. The serial port’s
parameters are 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
The port requires a straight serial cable with a female 9-pin subminiature-D
connector. Only pins 2, 3, and 5 are supported, as shown in Table 8.
Note:
For dust and ESD (electrostatic discharge) protection, a cover is provided for the
serial port and should be kept on the port whenever the serial port is not in use.
Table 8:
Serial Port Cabling Pin Layout
Pin
Signal
Description
1
NC
2
TX
Transmit data
3
RX
Receive data
4
NC
5
GND
Ground
6
NC
7
NC
8
NC
9
NC