HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 102

Floppy Disk Drive and Filler Panel Installed in the Carrier

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement 3. Insert the floppy disk drive into the carrier and secure the drive in the carrier using four of the T-10 Torx screws (two on each side). 4. Install the smaller of the two filler panels on top of the floppy disk drive as shown in Figure 4-10. Secure the filler panel with the two remaining T-10 Torx screws. Figure 4-10. Floppy Disk Drive and Filler Panel Installed in the Carrier 5. Connect the power and ribbon cables in the drive bay to the rear of the floppy disk drive. 6. Push the DDS-3 tape/floppy disk drive carrier assembly into the drive bay, taking care not to pinch the cables. Seat the carrier assembly flush against the front panel. 7. Insert and tighten the two T-15 Torx screws to secure the floppy disk drive to the front panel of the workstation. 8. Replace the front panel bezel. 9. After rebooting, use SAM to confirm that the floppy disk drive is recognized by the system. 98 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
98
Chapter 4
Field Replaceable Units (FRUs)
FRU Removal and Replacement
3.
Insert the floppy disk drive into the carrier and secure the drive in the carrier using
four of the T-10 Torx screws (two on each side).
4.
Install the smaller of the two filler panels on top of the floppy disk drive as shown in
Figure 4-10. Secure the filler panel with the two remaining T-10 Torx screws.
Figure 4-10. Floppy Disk Drive and Filler Panel Installed in the Carrier
5.
Connect the power and ribbon cables in the drive bay to the rear of the floppy disk drive.
6.
Push the DDS-3 tape/floppy disk drive carrier assembly into the drive bay, taking care
not to pinch the cables. Seat the carrier assembly flush against the front panel.
7.
Insert and tighten the two T-15 Torx screws to secure the floppy disk drive to the front
panel of the workstation.
8.
Replace the front panel bezel.
9.
After rebooting, use SAM to confirm that the floppy disk drive is recognized by the
system.