HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 113

towards the chassis floor.

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement 5. Insert and alternately tighten the two power supply jack screws. Take care to align the right side jack screw to the mainframe chassis. 6. Insert and tighten all bus bar thumbscrews using a #20 Torx bit. Inspect to ensure that the gold plated bus bars are not touching each other when torqued. CAUTION If the bus bars are not tightened sufficiently, system problems may result. 7. Replace the bus bar shield by aligning the edge with the power supply edge while inserting the hooks into the slots. Rock the bus bar shield into place by pressing down towards the chassis floor. 8. Insert and tighten the front, lower-left T-15 Torx screw and the two rear panel T-15 Torx screws. 9. Insert the PCI retainer clip. 10. Replace the top panel and the right side panel of the workstation. Chapter 4 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Chapter 4
109
Field Replaceable Units (FRUs)
FRU Removal and Replacement
5.
Insert and alternately tighten the two power supply jack screws. Take care to align the
right side jack screw to the mainframe chassis.
6.
Insert and tighten all bus bar thumbscrews using a #20 Torx bit. Inspect to ensure that
the gold plated bus bars are not touching each other when torqued.
CAUTION
If the bus bars are not tightened sufficiently, system problems may result.
7.
Replace the bus bar shield by aligning the edge with the power supply edge while
inserting the hooks into the slots. Rock the bus bar shield into place by pressing down
towards the chassis floor.
8.
Insert and tighten the front, lower-left T-15 Torx screw and the two rear panel T-15 Torx
screws.
9.
Insert the PCI retainer clip.
10. Replace the top panel and the right side panel of the workstation.