HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 91

Front Bezel and Outer Panels

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement Front Bezel and Outer Panels This section describes how to remove and replace the J5000 and J7000 workstation's front bezel, as well as the top and the two side outer panels. Note that you can perform certain operations, like removing and replacing hard disk drives, simply by opening the door on the front bezel of the workstation; the disk drives are accessible through the open door. Other operations require more access to the interior of the workstation, so you will need to remove the front bezel or outer panels to perform those procedures. CAUTION Do not attempt to operate the workstation with the front bezel, top panel, or side panels removed. In addition to maintaining FCC/EMI compliance, the front bezel, top panel, and side panels are needed to ensure proper air flow and, hence, sufficient system cooling. Removing the Front Bezel To remove the front bezel, do the following: 1. Open the right-hand door of the front bezel. If the door does not easily release, you may need the bezel lock's key to unlock the door. 2. Remove the two T-15 Torx bezel-detach screws on the top and bottom, right inside corners of the front bezel. 3. Grasp and pull out on the outer right edge of the front bezel, rotating the front bezel clockwise and pulling it away from the front panel. Replacing the Front Bezel To replace the front bezel, do the following: 1. Align the three metal bezel hooks into the three bezel hinge holes along the left edge of the workstation's front panel. 2. Press inward while rotating the front bezel counterclockwise. 3. Press firmly on the upper-right corner of the front bezel until it snaps into place. 4. Open the right-hand door of the front bezel and install the two T-15 Torx bezel-detach screws on the top and bottom, right inside corners of the front bezel. Chapter 4 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Chapter 4
87
Field Replaceable Units (FRUs)
FRU Removal and Replacement
Front Bezel and Outer Panels
This section describes how to remove and replace the J5000 and J7000 workstation’s front
bezel, as well as the top and the two side outer panels.
Note that you can perform certain operations, like removing and replacing hard disk
drives, simply by opening the door on the front bezel of the workstation; the disk drives are
accessible through the open door. Other operations require more access to the interior of
the workstation, so you will need to remove the front bezel or outer panels to perform those
procedures.
CAUTION
Do not attempt to operate the workstation with the front bezel, top panel, or
side panels removed. In addition to maintaining FCC/EMI compliance, the
front bezel, top panel, and side panels are needed to ensure proper air flow
and, hence, sufficient system cooling.
Removing the Front Bezel
To remove the front bezel, do the following:
1.
Open the right-hand door of the front bezel. If the door does not easily release, you may
need the bezel lock’s key to unlock the door.
2.
Remove the two T-15 Torx bezel-detach screws on the top and bottom, right inside
corners of the front bezel.
3.
Grasp and pull out on the outer right edge of the front bezel, rotating the front bezel
clockwise and pulling it away from the front panel.
Replacing the Front Bezel
To replace the front bezel, do the following:
1.
Align the three metal bezel hooks into the three bezel hinge holes along the left edge of
the workstation’s front panel.
2.
Press inward while rotating the front bezel counterclockwise.
3.
Press firmly on the upper-right corner of the front bezel until it snaps into place.
4.
Open the right-hand door of the front bezel and install the two T-15 Torx bezel-detach
screws on the top and bottom, right inside corners of the front bezel.