HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 97

CD Drive Optional, Removing a CD Drive, EMI Cover for the CD Drive, Replacing a CD Drive

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement CD Drive (Optional) This subsection describes how to remove and replace the optional CD drive. Removing a CD Drive: 1. Remove the front panel bezel and the top panel from the workstation. 2. In the top, right front of the workstation above the CD drive bay, remove the EMI (electromagnetic interference) cover that is held in place by tabs. The EMI cover is shown in Figure 4-4. Figure 4-4. EMI Cover for the CD Drive EMI cover 3. From the top of the workstation, reach behind the CD drive and disconnect the audio cable, power cable, and ATAPI interface ribbon cable from the rear of the CD drive. 4. Remove the two T-15 Torx screws securing the CD drive to the front panel of the workstation chassis. 5. Slide the CD drive carrier assembly out of the chassis guide rails. 6. To remove the CD drive from the carrier, remove the four T-10 Torx screws (two on each side) securing the CD drive to the carrier. Replacing a CD Drive: NOTE See the section titled "CD Drive (Optional) Configuration" on page 35 for information about configuring a CD drive for installation. 1. Remove the front panel bezel and the top panel from the workstation. 2. In the top, right front of the workstation above the CD drive bay, remove the EMI (electromagnetic interference) cover that is held in place by tabs. The EMI cover is shown in Figure 4-4 above. 3. If you are installing a new CD drive into the empty CD drive bay: a. Remove the two T-15 Torx screws securing the CD drive carrier to the front panel of the workstation. b. Slide the CD drive carrier out of the chassis guide rails. c. Remove the filler panel from the CD drive carrier as shown in Figure 4-5 on the next page. Chapter 4 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Chapter 4
93
Field Replaceable Units (FRUs)
FRU Removal and Replacement
CD Drive (Optional)
This subsection describes how to remove and replace the optional CD drive.
Removing a CD Drive:
1.
Remove the front panel bezel and the top panel from the workstation.
2.
In the top, right front of the workstation above the CD drive bay, remove the EMI
(electromagnetic interference) cover that is held in place by tabs. The EMI cover is
shown in Figure 4-4.
Figure 4-4. EMI Cover for the CD Drive
3.
From the top of the workstation, reach behind the CD drive and disconnect the audio
cable, power cable, and ATAPI interface ribbon cable from the rear of the CD drive.
4.
Remove the two T-15 Torx screws securing the CD drive to the front panel of the
workstation chassis.
5.
Slide the CD drive carrier assembly out of the chassis guide rails.
6.
To remove the CD drive from the carrier, remove the four T-10 Torx screws (two on each
side) securing the CD drive to the carrier.
Replacing a CD Drive:
NOTE
See the section titled “CD Drive (Optional) Configuration” on page 35 for
information about configuring a CD drive for installation.
1.
Remove the front panel bezel and the top panel from the workstation.
2.
In the top, right front of the workstation above the CD drive bay, remove the EMI
(electromagnetic interference) cover that is held in place by tabs. The EMI cover is
shown in Figure 4-4 above.
3.
If you are installing a new CD drive into the empty CD drive bay:
a.
Remove the two T-15 Torx screws securing the CD drive carrier to the front panel of
the workstation.
b.
Slide the CD drive carrier out of the chassis guide rails.
c.
Remove the filler panel from the CD drive carrier as shown in Figure 4-5 on the next
page.
EMI cover