HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 96

Removing the Hard Disk Drive from the Carrier, Replacing a Hard Disk Drive

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement 6. To remove the hard disk drive from the carrier, unscrew the four slotted pan screws from the sides of the carrier as shown in Figure 4-3. (You can then store the screws on top of the carrier rails as shown in Figure 4-3, if you wish.) Figure 4-3. Removing the Hard Disk Drive from the Carrier Replacing a Hard Disk Drive: NOTE If you are installing a new hard disk drive, the slotted pan screws for attaching the drive in the carrier are stored on the carrier rails. Also see the section titled "Hard Disk Drive Configuration" on page 34 for information about configuring a hard disk drive for installation. 1. Open the right door of the bezel on the workstation's front panel. 2. Perform the previous removal procedure in reverse order. NOTE To verify a good connection with the SCA hard disk interface (backplane board) connector, press firmly on the outside corners of the carrier. 92 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
92
Chapter 4
Field Replaceable Units (FRUs)
FRU Removal and Replacement
6.
To remove the hard disk drive from the carrier, unscrew the four slotted pan screws
from the sides of the carrier as shown in Figure 4-3. (You can then store the screws on
top of the carrier rails as shown in Figure 4-3, if you wish.)
Figure 4-3.
Removing the Hard Disk Drive from the Carrier
Replacing a Hard Disk Drive:
NOTE
If you are installing a new hard disk drive, the slotted pan screws for
attaching the drive in the carrier are stored on the carrier rails. Also see the
section titled “Hard Disk Drive Configuration” on page 34 for information
about configuring a hard disk drive for installation.
1.
Open the right door of the bezel on the workstation’s front panel.
2.
Perform the previous removal procedure in reverse order.
NOTE
To verify a good connection with the SCA hard disk interface (backplane
board) connector, press firmly on the outside corners of the carrier.