HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 117

Speaker

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement Speaker This section describes how to remove and replace the speaker, which is located in the fan/speaker mounting bracket in the bottom of the front, right side of the workstation. Removing the Speaker To remove the speaker, do the following: 1. Remove the top panel and the right side panel. 2. Remove the PCI retainer clip, which is located below the power supply. 3. Remove all I/O cards from the I/O board and note their locations for reinstallation later. See the removal procedures in the section "I/O Cards" on page 106 for details. 4. Disconnect the fan and speaker cables from the I/O board. 5. Pull on the fan/speaker mounting bracket tab that is closest to the internal chassis wall. 6. Rotate and slightly tilt the mounting bracket to remove it from the chassis. 7. Place the bracket on a flat surface with the speaker vertical to the surface. 8. Slide the speaker out of the guides in the fan/speaker mounting bracket. Replacing the Speaker To replace the speaker, do the following: 1. Reinsert the speaker in the fan/speaker mounting bracket. 2. Position the fan so that the flow arrow points towards the I/O card guide rails. 3. To avoid interference with the I/O card guide rails, you must thread the fan cable through the plastic slot adjacent to the release tab for the fan/speaker mounting bracket. 4. Align the mounting bracket to snap in place over the mounting bracket's housing posts. Slide the mounting bracket along the chassis floor until it snaps into place. Take care not to pinch the cables to the inner chassis wall. 5. Connect the fan and speaker cables to the I/O board. 6. Reinstall the I/O cards by following the replacement procedures in the section titled "I/O Cards" on page 106. 7. Insert the PCI retainer clip. 8. Replace the top panel and the right side panel of the workstation. Chapter 4 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Chapter 4
113
Field Replaceable Units (FRUs)
FRU Removal and Replacement
Speaker
This section describes how to remove and replace the speaker, which is located in the
fan/speaker mounting bracket in the bottom of the front, right side of the workstation.
Removing the Speaker
To remove the speaker, do the following:
1.
Remove the top panel and the right side panel.
2.
Remove the PCI retainer clip, which is located below the power supply.
3.
Remove all I/O cards from the I/O board and note their locations for reinstallation later.
See the removal procedures in the section “I/O Cards” on page 106 for details.
4.
Disconnect the fan and speaker cables from the I/O board.
5.
Pull on the fan/speaker mounting bracket tab that is closest to the internal chassis wall.
6.
Rotate and slightly tilt the mounting bracket to remove it from the chassis.
7.
Place the bracket on a flat surface with the speaker vertical to the surface.
8.
Slide the speaker out of the guides in the fan/speaker mounting bracket.
Replacing the Speaker
To replace the speaker, do the following:
1.
Reinsert the speaker in the fan/speaker mounting bracket.
2.
Position the fan so that the flow arrow points towards the I/O card guide rails.
3.
To avoid interference with the I/O card guide rails, you must thread the fan cable
through the plastic slot adjacent to the release tab for the fan/speaker mounting
bracket.
4.
Align the mounting bracket to snap in place over the mounting bracket’s housing posts.
Slide the mounting bracket along the chassis floor until it snaps into place. Take care
not to pinch the cables to the inner chassis wall.
5.
Connect the fan and speaker cables to the I/O board.
6.
Reinstall the I/O cards by following the replacement procedures in the section titled
“I/O Cards” on page 106.
7.
Insert the PCI retainer clip.
8.
Replace the top panel and the right side panel of the workstation.