Honeywell HNVE1 Reference Guide - Page 72

Board Setup View, Table 5-7, PTZ Configuration Settings, Protocol, Baud Rate, Stop Bit

Get Honeywell HNVE1 PDF manuals and user guides View all Honeywell HNVE1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Encoder and Device Configuration Figure 5-10 Board Setup View 1. Select the Board Setup tab. 2. Select from six PTZ dome protocols preconfigured for the dome you have connected to the encoder. Each PTZ dome has specific baud rate, stop bit, and parity settings. • Baud Rate settings range from 2400 to 115200. • Stop Bits settings range from 1 to 2. • Parity Bits settings range from None, Odd, Even. Note For the PTZ dome and the HNVE1 to be able to communicate, the PTZ switch settings on the PTZ dome and the HNVE1 encoder must be the same. See Configuring a PTZ Dome on page 62 for more information about PTZ switches. The encoder provides the option of six protocols. The preconfigured values of the baud rate, stop bit, and parity for each protocol are listed in this table: Table 5-7 PTZ Configuration Settings Protocol Pelco P Pelco D Diamond IntelliBusTM VCL MAXPRO-Net Baud Rate 4800 2400 9600 38400 9600 9600 Stop Bit 1 1 1 2 2 2 Parity None None Even None None Even 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
72
Encoder and Device Configuration
Figure 5-10
Board Setup View
1.
Select the
Board Setup
tab.
2.
Select from six PTZ dome protocols preconfigured for the dome you have connected
to the encoder. Each PTZ dome has specific baud rate, stop bit, and parity settings.
•
Baud Rate settings range from 2400 to 115200.
•
Stop Bits settings range from 1 to 2.
•
Parity Bits settings range from None, Odd, Even.
Note
For the PTZ dome and the HNVE1 to be able to communicate, the PTZ switch
settings on the PTZ dome and the HNVE1 encoder must be the same. See
Configuring a PTZ Dome
on page
62
for more information about PTZ
switches.
The encoder provides the option of six protocols. The preconfigured values of the baud
rate, stop bit, and parity for each protocol are listed in this table:
Table 5-7
PTZ Configuration Settings
Protocol
Baud Rate
Stop Bit
Parity
Pelco P
4800
1
None
Pelco D
2400
1
None
Diamond
9600
1
Even
IntelliBus
TM
38400
2
None
VCL
9600
2
None
MAXPRO-Net
9600
2
Even