IBM 8479 Hardware Maintenance Manual - Page 24

manufacturer.

Get IBM 8479 - Eserver xSeries 200 PDF manuals and user guides
UPC - 087944653912
View all IBM 8479 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

CAUTION: When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If the server has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations. Do the following to replace the battery: 1. Read "Before you begin" on page 40, and follow any special handling and installation instructions supplied with the replacement battery. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the server cover. 3. Remove the battery: a. Use one finger to press the top of the battery clip away from the battery until the battery releases upward from the socket. b. Lift and remove the battery from the battery socket. 4. Do the following to insert the new battery: a. Tilt the battery so that you can insert it into the socket under the battery clip. b. As you slide it under the battery clip, press the battery down into the socket. 5. Reinstall the server cover and connect the cables. 6. Turn on the server. 7. Start the Configuration/Setup Utility program and set configuration parameters. v Set the server date and time. v Set the power-on password. v Reconfigure the server. 16 xSeries 200 Type 8479 and xSeries 200VL Type 8481: Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
CAUTION:
When
replacing
the
battery,
use
only
IBM
Part
Number
33F8354
or
an
equivalent
type
battery
recommended
by
the
manufacturer.
If
the
server
has
a
module
containing
a
lithium
battery,
replace
it
only
with
the
same
module
type
made
by
the
same
manufacturer.
The
battery
contains
lithium
and
can
explode
if
not
properly
used,
handled,
or
disposed
of.
Do
not:
v
Throw
or
immerse
into
water
v
Heat
to
more
than
100°C
(212°F)
v
Repair
or
disassemble
Dispose
of
the
battery
as
required
by
local
ordinances
or
regulations.
Do
the
following
to
replace
the
battery:
1.
Read
“Before
you
begin”
on
page
40,
and
follow
any
special
handling
and
installation
instructions
supplied
with
the
replacement
battery.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
external
cables
and
power
cords;
then,
remove
the
server
cover.
3.
Remove
the
battery:
a.
Use
one
finger
to
press
the
top
of
the
battery
clip
away
from
the
battery
until
the
battery
releases
upward
from
the
socket.
b.
Lift
and
remove
the
battery
from
the
battery
socket.
4.
Do
the
following
to
insert
the
new
battery:
a.
Tilt
the
battery
so
that
you
can
insert
it
into
the
socket
under
the
battery
clip.
b.
As
you
slide
it
under
the
battery
clip,
press
the
battery
down
into
the
socket.
5.
Reinstall
the
server
cover
and
connect
the
cables.
6.
Turn
on
the
server.
7.
Start
the
Configuration/Setup
Utility
program
and
set
configuration
parameters.
v
Set
the
server
date
and
time.
v
Set
the
power-on
password.
v
Reconfigure
the
server.
16
xSeries
200
Type
8479
and
xSeries
200VL
Type
8481:
Hardware
Maintenance
Manual