IBM 887022X Installation Guide - Page 21

Opening

the

cover

Complete

the

following

steps

to

open

the

server

cover:

1.

Read

the

safety

information

beginning

on

page

v

and

“Installation

guidelines”

on

page

7.

2.

Before

opening

the

top

cover,

you

must

remove

the

rack-support

wheels

and

handles

from

the

server.

See

the

Rack

Installation

Instructions

for

information.

3.

Press

the

release

latch

on

the

left

half

of

the

top

cover

to

the

right.

4.

Using

the

finger

hole

in

the

release

latch,

open

the

left

half

of

the

cover;

then,

open

the

right

half

of

the

cover.

Attention:

For

proper

cooling

and

airflow,

close

the

cover

before

turning

on

the

server.

Operating

the

server

for

extended

periods

of

time

(more

than

30

minutes)

with

the

cover

open

might

damage

server

components.

The

SMP

Expansion

Module

The

SMP

Expansion

Module

contains

the

XceL4

system

cache,

DIMMs,

microprocessors,

and

voltage

regulator

modules

(VRMs).

This

section

provides

instructions

for

removing

and

installing

the

SMP

Expansion

Module,

microprocessors,

VRMs,

and

DIMMs.

The

following

notes

describe

components

in

the

SMP

Expansion

Module

and

other

information

that

you

must

consider

when

installing

an

SMP

Expansion

Module:

v

Use

two

hands

to

install

or

remove

an

SMP

Expansion

Module.

Do

not

allow

the

expansion

module

to

come

in

contact

with

the

center

plane

while

lifting

it

out

of

or

setting

it

into

the

server.

v

For

your

server

to

operate

properly,

there

must

be

a

minimum

of

one

SMP

Expansion

Module

installed.

v

An

SMP

Expansion

Module

must

contain

at

least

one

microprocessor

and

two

DIMMs.

v

If

there

is

only

one

SMP

Expansion

Module

installed

in

the

server,

an

SMP

baffle

must

be

installed

in

place

of

the

upper

SMP

Expansion

Module

to

ensure

proper

cooling

of

the

server.

NOTE:

FOR PROPER AIRFLOW, REPLACE FAN WITHIN 2 MINUTES

FRONT OF BOX

NOTE:

FOR PROPER AIRFLOW, REPLACE FAN WITHIN 2 MINUTES

FRONT OF BOX

Latch

Figure

3.

Opening

the

cover

Chapter

2.

Installing

options

9

Section	Page
Contents	5
Safety	7
Chapter 1. Introduction	13
The IBM Eserver Documentation CD	14
Hardware and software requirements	14
Using the Documentation Browser	14
Notices and statements used in this publication	15
Features and specifications	16
Major components of the xSeries 445 server	17
Chapter 2. Installing options	19
Installation guidelines	19
System reliability guidelines	19
Working inside the server with the power on	20
Handling static-sensitive devices	20
Opening the cover	21
The SMP Expansion Module	21
Removing an SMP Expansion Module and cover	23
Installing and replacing a microprocessor	27
Installing a memory module	31
Installing DIMMs	33
Reinstalling an SMP Expansion Module and cover	35
Installing an adapter	38
Cabling a ServeRAID adapter	41
Installing the serial port	43
Completing the installation	45
Installing the server in the rack cabinet	45
Connecting the cables	46
SMP Expansion Port cabling	47
RXE Expansion and Management Port cabling	53
Power cabling	60
SCSI cabling	60
USB cabling	60
Video cabling	60
Mouse cabling	60
Keyboard cabling	61
Gigabit Ethernet cabling	61
Remote Supervisor Adapter cabling	61
Chapter 3. Server controls, LEDs, and power	63
Front view	63
Rear view	65
Server power features	68
Turning on the server	68
Turning off the server	69
Chapter 4. Configuring your server	71
Using the ServerGuide Setup and Installation CD	72
Using the Configuration/Setup Utility program	72
Using the LSI Logic Configuration Utility program	73
Using the ServeRAID configuration programs	74
Using the Remote Supervisor Adapter	74
Using the Integrated System Management Firmware Update Utility program	74
Configuring scalable partitions	75
Creating a scalable partition	75
Deleting a scalable partition	77
Chapter 5. Updating IBM Director	79
Chapter 6. Solving problems	81
Diagnostic tools overview	81
POST beep code descriptions	82
ServerGuide startup problems	82
Troubleshooting charts	83
Light path diagnostics feature overview	88
Identifying problems using the light path diagnostics feature	89
The diagnostic panel	89
LEDs on the top of the server	89
LEDs on the SMP Expansion Modules and system boards	89
Light path diagnostics table	90
Appendix A. Getting help and technical assistance	93
Before you call	93
Using the documentation	93
Getting help and information from the World Wide Web	94
Software service and support	94
Hardware service and support	94
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002	95
Part 1 - General Terms	95
Part 2 - Country-unique Terms	98
Part 3 - Warranty Information	109
Appendix C. Notices	111
Edition notice	111
Trademarks	112
Important notes	113
Product recycling and disposal	113
Battery return program	114
Electronic emission notices	114
Federal Communications Commission (FCC) statement	114
Industry Canada Class A emission compliance statement	115
Australia and New Zealand Class A statement	115
United Kingdom telecommunications safety requirement	115
European Union EMC Directive conformance statement	115
Taiwanese Class A warning statement	115
Chinese Class A warning statement	116
Japanese Voluntary Control Council for Interference (VCCI) statement	116
Power cords	116

IBM 887022X Installation Guide - Page 21

Opening, cover, Expansion, Module

Page 21 highlights