Icom IC-7100 Instruction Manual

Icom IC-7100 Manual

Get Icom IC-7100 PDF manuals and user guides View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-7100 manual content summary:

  • Icom IC-7100 | Instruction Manual - Page 1
    INSTRUCTION MANUAL HF/VHF/UHF ALL MODE TRANSCEIVER i7100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
  • Icom IC-7100 | Instruction Manual - Page 2
    for purchasing this fine Icom product. The IC-7100 hf/vhf/uhf all mode transceiver is designed and build with Icom's superior technology and craftsmanship combining traditional analog technologies with the new digital technology, Digital Smart Technologies for Amateur Radio (D-STAR), for a balanced
  • Icom IC-7100 | Instruction Manual - Page 3
    connected, set the transceiver's RF output power to less than the linear amplifier's maximum input level, otherwise, the linear amplifier will be damaged. Use Icom microphones only (supplied or optional). Other manufacturer's microphones have different pin assignments, and connection to the IC-7100
  • Icom IC-7100 | Instruction Manual - Page 4
    the file. • T o close the Menu screen, click [Quit]. Opens the Basic Instructions (this manual) Opens the Advanced Instructions Opens the Schematic diagram Opens the Glossary Installs the Adobe® Reader® Quits the menu screen To read the guide or instructions, Adobe® Reader® is required. If
  • Icom IC-7100 | Instruction Manual - Page 5
    INSTALLATION AND CONNECTIONS Section 3 BASIC OPERATION Section 4 D-STAR INTRODUCTION Section 5 D-STAR OPERATION Section 6 SET MODE Section 7 INSTALLATION NOTES "AI" means "Advanced Instructions." "sec. MM" means section number. So when "(AI sec. MM)" is described on this manual, see the PDF
  • Icom IC-7100 | Instruction Manual - Page 6
    CLR M-CH BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD io !0 !1 q P OWER SWITCH•AF VOLUME [PWR]•[AF] (p. 3-2) ➥➥Push to turn ON the transceiver power. • First, confirm the DC power source is turned ON. ➥➥Hold
  • Icom IC-7100 | Instruction Manual - Page 7
    slightly differentsounding voice characteristics. ❍ When the PBT LED lights green (Mode: SSB/CW/RTTY/AM) ➥ R otate to adjust the receiver's IF filter pass- band width using the DSP circuit. ➥ H old down for 1 second to reset the PBT set- tings. • The PBT is adjustable in 50 Hz steps in
  • Icom IC-7100 | Instruction Manual - Page 8
    Controller - Front panel (Continued) PWR AF RF/SQL i7100 TX / RX CLR M-CH BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD !2 !3 !4 !5 !6 !7 !8 !9 @0 @1 !2 NOISE BLANKER KEY NB (AI sec. 5) (Mode: SSB/CW
  • Icom IC-7100 | Instruction Manual - Page 9
    to enter or exit the SET mode. • "Voice Memo," "Call Sign," "RX History," "DV Memory," "My Station," "DV Set," "GPS," "SPEECH," "QSO/RX Log," "Function," "Tone Control," "Connectors," "Display," "Time Set," "SD Card" and "Others" set group are selectable. !9 QUICK MENU KEY QUICK ➥ Push to open
  • Icom IC-7100 | Instruction Manual - Page 10
    1 PANEL DESCRIPTION Controller - Front panel (Continued) PWR AF RF/SQL i7100 TX / RX CLR M-CH BANK PBT RIT RIT TUNER/CALL MENU NB NR MIC/RF PWR SPEED/PITCH P.AMP ATT NOTCH DR SET QUICK AUTO TUNE RX�CS SPEECH XFC MPAD @5 @4 @2 @3 @2 SPEECH•LOCK KEY SPEECH ❍ SPEECH KEY Operation (p. 3-
  • Icom IC-7100 | Instruction Manual - Page 11
    10 Hz or 1 Hz steps. u GPS ICON (AI sec. 10) ➥ Appears when valid position data is received from a GPS receiver that is connected to the [DATA1] jack. ➥ Blinks when invalid data is received from the GPS receiver. i SD CARD ICON ➥➥" " appears when an SD card is inserted and " " alternately blinks
  • Icom IC-7100 | Instruction Manual - Page 12
    . • Push MENU to change the set of functions assigned to the touch keys. • T oggles the function display menu between M-1, M-2 and M-3 menus or D-1 and D-2 menus. !8 MULTI-FUNCTION METER INDICATION ➥➥Displays the signal strength while receiving. ➥➥Displays the relative output power, SWR, ALC or
  • Icom IC-7100 | Instruction Manual - Page 13
    " appears when the Full Break-in function is the HF, 50/70 MHz frequency band, either "P.AMP1" Control) function is turned ON. (Mode: DV) ➥➥" " appears when the EMR (Enhanced Moni- tor Receive) communication mode is selected. (AI sec. 9) • In the EMR communication mode, no call sign setting
  • Icom IC-7100 | Instruction Manual - Page 14
    1 PANEL DESCRIPTION Controller - Multi-function keys ➥➥Push MENU to change the set of functions assigned to touch keys. • T oggles the function display menu between M-1, M-2 and M-3 menus or D-1 and D-2 menus. • Functions vary, depending on the operating mode. • In the DR mode, the D-1 and D-2
  • Icom IC-7100 | Instruction Manual - Page 15
    an SD card. Touch to display the "VOICE TX" screen or the "VOICE" (Root) screen, depending on the "VOICE 1st Menu" option in the "Function" Set mode (p. 6-6). SET > Function > VOICE 1st Menu • Push MENU to return to the previous screen. MEMORY KEYER KEY [KEYER] (AI sec. 4) (Mode: CW) Touch
  • Icom IC-7100 | Instruction Manual - Page 16
    (AI sec. 15) This function requires to insert an SD card. Touch to display the "VOICE TX" screen or the "VOICE" (Root) screen, depending on the "VOICE 1st Menu" option in the "Function" Set mode (p. 6-6). SET > Function > VOICE 1st Menu • Push MENU to return to the previous screen. CALL SIGN KEY
  • Icom IC-7100 | Instruction Manual - Page 17
    30 or SM-50. • A microphone connector is also available on the Main unit. DO NOT simultaneously connect two microphones. r MAIN UNIT CONNECTOR [MAIN UNIT] Connects to the Main unit using with the supplied OPC-2253 Control cable. • T he OPC-2253 Control cable is 3.5 meter (11.5 feet) long. DO
  • Icom IC-7100 | Instruction Manual - Page 18
    problems. oiu r TUNER CONTROL SOCKET [TUNER] (p. 2-6) Connect the control cable from an optional AH-4 hf/ 50 mhz automatic antenna tuner. t DC POWER SOCKET [DC 13.8V] (p. 2-7) Connect 13.8 V DC through the supplied DC power cable. Rear panel view y CONTROLLER CONNECTOR [CONTROLLER] Connects
  • Icom IC-7100 | Instruction Manual - Page 19
    port Other items • USB cable (supplied with the transceiver) • PC software (such as the optional RS-BA1 or CS- 7100) NEVER connect the transceiver to a PC until the USB driver installation has been completed. About the modulation input: Select "USB" in the "Connectors" Set mode item "DATA OFF MOD
  • Icom IC-7100 | Instruction Manual - Page 20
    *3) band voltage output. (AI sec. 19) Output voltage: --- 0 to 8 V ALC ALC voltage input. Control voltage: Input impedance: -4 V to 0 V More than 3.3 k˘ Color refers to An external equipment Input voltage (High): 2.0 V to 20.0 V the cable strands controls the transceiver. Input voltage (Low
  • Icom IC-7100 | Instruction Manual - Page 21
    input SQL SW When the HM-151 is not connected; Squelch switch SPECIFICATIONS Maximum 10 mA UP: Ground DN: Ground through 470 ˘ - - - - - - Open: 'Low' level Close: 'High' level *1 Y ou can change this setting in "MIC AF Out" of the "Function" Set mode. (p. 6-6) SET > Function > MIC AF Out 1-17
  • Icom IC-7100 | Instruction Manual - Page 22
    MIC GAIN LOW CUT t P TT LOCK INDICATOR [LOCK] (Only for the SM-30) Lights red when the PTT lock switch (w) is ON. y M IC GAIN VOLUME [MIC GAIN] Rotate to adjust the microphone output level. • Use this control as an addition to the microphone gain setting of the connected transceiver. Rotating
  • Icom IC-7100 | Instruction Manual - Page 23
    r t SPCH /LOCK TUNER /CALL XFC V/M MW F-1 F-2 1.8 1 3.5 2 7 3 MODE 10 14 18 4 5 Set mode (p. 6-6). SET > Function > Lock Function w PTT SWITCH [PTT] (p. 3-23) Hold down to transmit, release to receive band. • Icom's triple band stacking register memorizes 3 frequencies in each band.
  • Icom IC-7100 | Instruction Manual - Page 24
    the RX monitoring mode. (p. 6-3) !3 TUNER/CALL KEY [TUNER/CALL] ❍ ANTENNA TUNER KEY Operation (AI sec. 16) (Frequency band: HF, 50/70* MHz) ➥ Push to turn an optional antenna tuner ON or OFF (bypass). ➥ Hold down for 1 second to manually start the antenna tuner. • If the tuner cannot
  • Icom IC-7100 | Instruction Manual - Page 25
    Main unit installation 2-3 Connect to the controller 2-4 Required Connections to a Transceiver 2-5 The External Units Connections to a Transceiver 2-6 Power Supply Connections 2-7 DDConnecting the PS-126 power supply 2-7 DDConnecting a non-Icom DC power supply 2-7 Linear Amplifier Connections
  • Icom IC-7100 | Instruction Manual - Page 26
    case, an antenna tuner is useful to match the transceiver and antenna. Low SWR allows full power for transmitting. The IC-7100 has an SWR meter to continuously monitor the antenna SWR. Antenna connection Connect the cable from an HF, 50/70 MHz antenna to the [ANT 1] connector. Connect the cable from
  • Icom IC-7100 | Instruction Manual - Page 27
    trouble. Rear panel Controller To the [CONTROLLER] connector Using Ferrite EMI filter* Depending on the installed condition of the transceiver, malfunction may occur by the wraparound of the electric wave. This problem can be resolved by using the Ferrite EMI filter. * The filter connection
  • Icom IC-7100 | Instruction Manual - Page 28
    damage the transceiver. The HM-151 is designed to use with the IC-7000/ IC-7100 series ONLY. OPC-589 HM-36 SM-50 • External Keypad Control the CW memory keyer transmission from external keypad by connecting control circuit to MIC connector. Set the "Keyer" item in the "Connectors" Set mode to
  • Icom IC-7100 | Instruction Manual - Page 29
    [ANT1] HF, 50/70 MHz BANDS CONNECTOR (P. 2-3) Connect a 50 Ω antenna for the 144/430 MHz frequency bands or 74.8 MHz and above. Connect a 50 Ω antenna for the HF, 50/70 MHz frequency bands or below 74.8 MHz. IC-7100 [DC 13.8V] DC POWER SUPPLY (P. 2-7) Use a power supply with 13.8 V DC output and
  • Icom IC-7100 | Instruction Manual - Page 30
    Set mode (AI sec. 17), the receiving tone can normally be output from the [ACC] socket, and the [USB] port can output an IF signal (12 kHz). This is required for the Software-Defined Radio (SDR) operation. The Digital Radio Mondiale (DRM) broadcast can be received using SDR. CAUTION: DO NOT connect
  • Icom IC-7100 | Instruction Manual - Page 31
    2 INSTALLATION AND CONNECTIONS Power Supply Connections Make sure the [POWER] switch is OFF before connecting the DC power cable. • W e recommend using Icom's optional power supply (PS-126: DC13.8 V/25 A). DDConnecting the PS-126 power supply Use the attached AC cable to connect to AC outlet.
  • Icom IC-7100 | Instruction Manual - Page 32
    70 MHz band transmission is available, depending on the transceiver version. To an antenna Non-Icom Linear amplifier RF OUT RF IN ALC SEND [ANT1]*2 Relay Switching diode ALC (Blue) HSEND (Orange) /VSEND GND IC-7100 ACC 13.8 V (Gray) 13-pin plug with ACC cable *2When connecting a 144 MHz
  • Icom IC-7100 | Instruction Manual - Page 33
    Power ON 3-2 DDBefore first applying power 3-2 DDTuning ON the power 3-2 Selecting a Function menu 3-3 Selecting VFO/Memory mode 3-4 VFO operation 3-5 DDSelecting VFO A or VFO B 3-5 DDVFO equalization 3-5 Selecting a frequency band 3-6 DDUsing the band stacking registers 3-6 Setting
  • Icom IC-7100 | Instruction Manual - Page 34
    , VFO settings, menu group's contents) without clearing certain data. SET(C) > Others > Reset > Partial Reset • During start-up, the transceiver displays "PARTIAL RESET," then its initial VFO frequencies when resetting is complete. See the PDF type Advanced Instruction's Section 19 for resetting
  • Icom IC-7100 | Instruction Manual - Page 35
    once or twice to select the "D-1" screen (D-1 menu) or "D-2" screen (D-2 menu). • Functions vary, depending on the operating mode. (p. 1-10 to p. 1-12) Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom
  • Icom IC-7100 | Instruction Manual - Page 36
    (M-1 menu). • Touch [V/M](D) to select the VFO or memory mode. • Touch [V/M](D) for 1 second to copy the selected memory channel contents to the VFO mode. (See the PDF type Advanced Instruction's Section 11 for details.) VFO mode icon "M-1" screen Touch [V/M] Programming 10.12000 MHz/CW into
  • Icom IC-7100 | Instruction Manual - Page 37
    in the VFO mode, push MENU (C) one or more times to select the "M-1" screen (M-1 menu). wwTouch [A/B](D) to switch between the VFO A and VFO B. • "VFOA" or "VFOB" appears as each VFO is selected. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 38
    . See the table below for a list of the available frequency bands and their default frequency and mode settings. Cancel edit Operating mode Example: Touch "21" in the above screen The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom
  • Icom IC-7100 | Instruction Manual - Page 39
    / LOCK] Switch" item of the "Function" Set mode, pushing [SPEECH/LOCK] turns OFF the lock function. (p. 6-6) SET(C) > Function > [SPEECH/LOCK] switch Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom
  • Icom IC-7100 | Instruction Manual - Page 40
    3 BASIC OPERATION Setting frequency (Continued) DDQuick Tuning function The operating frequency can be changed in 'kHz' or 'MHz' steps for quick tuning. Select the desired tuning step in each operating frequency band and mode. q Touch the kHz digits to select the 'kHz' Quick Tuning function step,
  • Icom IC-7100 | Instruction Manual - Page 41
    MENU (C) to return to the normal operating screen. rrRepeat steps q to e to select the Quick tuning steps for other modes. Touch the kHz digits in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch the Hz digits for 1
  • Icom IC-7100 | Instruction Manual - Page 42
    , touch the item for 1 second to open the Default set window, then select the "Default" to reset to the de- fault setting. rrPush SET(C) to exit the Set mode. The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D: Display (Touch
  • Icom IC-7100 | Instruction Manual - Page 43
    digit, touch [ENT](D) to set all uninputted digits to "0." • If desired, touch "CE" to delete entering. • If desired, touch [](D) or push MENU the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Touch the MHz digits Touch
  • Icom IC-7100 | Instruction Manual - Page 44
    offset frequency input qqTouch the MHz digits to enter the Band selection dis- play. wwTouch [F-INP](D) to enter the Direct input screen. eeIf the Shift direction is minus, touch "• (-)." • [SPLIT] changes to [-SPLIT], and displays the Minus setting mode. rrTouch the desired number to enter
  • Icom IC-7100 | Instruction Manual - Page 45
    the programmed range. • If desired, touch the item for 1 second to open the Default set window, then select the "Default" to reset to the de- fault setting. rrPush SET(C) to exit the Set mode. If the "Beep Level" item is set to "0," the Band edge beep does not sound. The beep output level
  • Icom IC-7100 | Instruction Manual - Page 46
    Band Edge" item of the "Function" Set mode. Function > User Band Edge ttFollow the instructions in the next topics to delete, insert, edit, change or reset Band edges. yyAfter you have finished, push SET(C) to exit the Set mode. • Deleting a Band edge qqEnter the "User Band Edge" screen. SET
  • Icom IC-7100 | Instruction Manual - Page 47
    or push MENU (C) to return to the "Function" Set screen. • Editing a new Band edge qqEnter the "User Band Edge" screen. SET(C) > Function > User Band Edge wwTouch touch [ENT] The L, R, C or D in the instructions indicate the part of the controller. L: Left side, R: Right side, C: Center bottom D:
  • Icom IC-7100 | Instruction Manual - Page 48
    Band Edge" screen. SET(C) > Function > User Band Edge wwTouch any band edges for 1 second. eeTouch "Default." • "Initialize Edges?" is displayed. rrTouch [YES](D). • Resets all band edge frequencies to default settings. • If desired, touch "NO" to cancel resetting. ttTouch [](D) or push MENU
  • Icom IC-7100 | Instruction Manual - Page 49
    USB CW CW-R RTTY RTTY-R AM* FM WFM (Only RX) DV LSB LSB data USB USB data AM AM data FM FM data * On the 144 MHz or 430 MHz bands, only the RX operation is available in the AM mode. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 50
    Selecting the Audio volume ➥➥Rotate [AF] (L) control clockwise to increase the audio output level, counterclockwise to decrease it. Increases [AF] Decreases Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center
  • Icom IC-7100 | Instruction Manual - Page 51
    open. Noise squelch (FM/DV modes) Recommended level Maximum RF gain RF gain adjustable range S-meter squelch • When used as an RF gain control (Squelch is fixed open; SSB, CW, RTTY only) ❍ Adjusting RF gain (Receive sensitivity) Normally, [RF/SQL] (L) is set to the 12 o'clock position. Rotate
  • Icom IC-7100 | Instruction Manual - Page 52
    switch to announce the appropriate mode, when the "MODE SPEECH" item is set to "ON" in the "SPEECH" Set mode. (p. 6-4) SET(C) > SPEECH > MODE SPEECH Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom
  • Icom IC-7100 | Instruction Manual - Page 53
    (C) to exit the Set mode. DDTuning ON the MODE announcement When this function is ON, the selected operating mode is verbally announced when a mode is selected. qqPush SET(C) to enter the Set mode. wwTouch the "MODE SPEECH" item of the "SPEECH" Set mode. SPEECH > MODE SPEECH • If the specified
  • Icom IC-7100 | Instruction Manual - Page 54
    power meter, SWR meter, ALC meter or COMP meter. • Po : Displays the relative RF output power. • SWR : Displays the SWR of the antenna at the frequency. • ALC : Displays the ALC meter. RF output power is displayed in % (percent), and it becomes the S-meter in receive. ALC zone When ALC meter is
  • Icom IC-7100 | Instruction Manual - Page 55
    power settings are independently memorized in the HF, 50, 70, 144 and 430 MHz bands. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) [BANK] MENU MIC/RF PWR TX/RX LED Output
  • Icom IC-7100 | Instruction Manual - Page 56
    MIC gain. When the MIC gain is adjusted too high, your transmitted voice may be distorted. rrR elease [PTT] to receive. ttPush MENU (C) to close the display. ❍ In the SSB mode: Touch the TX meter to select the ALC meter. Then, while speaking into the microphone, rotate [M-CH] (L) so that the
  • Icom IC-7100 | Instruction Manual - Page 57
    the repeater frequency band shown below. 1200 MHz: A (B in Japan) 430 MHz: B (A in Japan) 144 MHz: C (no D-STAR repeaters in Japan) "AI" means "Advanced Instructions." "sec. MM" means section number. So when "(AI sec. MM)" is described on this manual, see the PDF type Advanced Instruction's section
  • Icom IC-7100 | Instruction Manual - Page 58
    programming Before starting D-STAR, the following steps are needed. IMPORTANT! STEP 1 Entering your call sign (MY) into the transceiver SET(C) to enter the Set mode. wwTouch the "MY Call Sign" item of the "My Station" Set mode D in the instructions indicate the part of the controller. L: Left side
  • Icom IC-7100 | Instruction Manual - Page 59
    screen. Call sign edit screen Move the cursor Delete a character Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) Enter "JA3YUA" into [MY1]. q e q Touch "JKL" to enter
  • Icom IC-7100 | Instruction Manual - Page 60
    "MY" (Your own call sign) programming 2. Enter the Call Sign (Continued) ooTouch the entered call sign to set the call sign to be used. !0 P ush SET(C) to exit the Set mode. ✓✓ Convenient! If necessary, enter a note of up to 4 characters, such as the model of the transceiver, name, area name, and
  • Icom IC-7100 | Instruction Manual - Page 61
    repeater through the internet. • T he transceiver can be operated in the digital voice mode, including low-speed data operation, for both transmit and receive. 4 D-STAR INTRODUCTION About the DR (D-STAR Repeater) mode The DR (D-STAR Repeater) mode is one mode you can use for D-STAR repeater
  • Icom IC-7100 | Instruction Manual - Page 62
    area NOTE: • Programming the repeater list is required for DR mode operation. (AI sec. 9) • Before operating in the DV mode, be sure to method acceptable to your local procedures. • T he transceiver has a Time-Out Timer function for digital repeater operation. The timer limits a continuous trans-
  • Icom IC-7100 | Instruction Manual - Page 63
    the RX History 5-17 DDUsing the TX History 5-18 DDDirectly inputting (UR 5-19 DDDirectly inputting (RPT 5-20 Section 1 panel description Section 2 INSTALLATION AND CONNECTIONS Section 3 BASIC OPERATION Section 4 D-STAR INTRODUCTION Section 5 D-STAR OPERATION Section 6 SET MODE Section
  • Icom IC-7100 | Instruction Manual - Page 64
    Japan" yyTouch your access repeater. • Example: "Hirano" • T he transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." 2. Set transceiver returns to the DR mode screen, and "CQCQCQ" is set in "TO." 3. Hold down [PTT] to transmit • W hile holding down [PTT], the TX/RX
  • Icom IC-7100 | Instruction Manual - Page 65
    Japan" !1 Touch the destination repeater. • Example: "Hamacho" • T he transceiver returns to the DR mode screen, and the selected repeater is set specific station by simply saying their call sign. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 66
    5 D-STAR OPERATION D-STAR Operating procedures (Continued) < Communication example for a Gateway call> INTERNET JA3YUA calling to JP1YIU port A through JP3YHH port B. JA3YUA, this is JM1ZLK. Hello, how are you? • • • JM1ZLK, this is JA3YUA. Thanks for the nice QSO and I hope to talk to you
  • Icom IC-7100 | Instruction Manual - Page 67
    "RX" is displayed when: • The repeater call sign programming is mode through the internet, some packets may be lost due to network error, or the caller's signal is weak getting into the repeater. In such a case, "L" is displayed to indicate that Packet Loss has occurred. When the transceiver receives
  • Icom IC-7100 | Instruction Manual - Page 68
    station call sign is an- nounced if the RX>CS Speech function is set to ON in the "SPEECH" Set mode. SET (C) > SPEECH > RX>CS SPEECH • If you want to select another call sign in the RX history, rotate [DIAL] while holding down AUTO TUNE RX�CS (R). NOTE: When a received signal is weak, or during DR
  • Icom IC-7100 | Instruction Manual - Page 69
    own and the repeater's location. The nearest repeaters in your transceiver's repeater list are displayed as the available choices. While DR mode scanning • When the "FROM" data is stored in the TX History. Setting from the TX History (p. 5-12) Select a repeater that you have accessed before, from
  • Icom IC-7100 | Instruction Manual - Page 70
    the repeater area or name. (Example: "Hirano") • T he transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display
  • Icom IC-7100 | Instruction Manual - Page 71
    not receive the transceiver's signal, because the repeater's output power is higher than the transceiver's. The DR mode scan also scans simplex frequencies if they are entered in the repeater list. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 72
    as the available choices. To receive your own position, connect an external NMEA format compatible receiver to the transceiver according to the instructions. (See AI sec. 10 for connecting the third party GPS receiver) If you set your position into the "Manual" item of the "GPS Set" Set mode, and
  • Icom IC-7100 | Instruction Manual - Page 73
    transceiver returns to the DR mode screen, and the selected repeater is set in the instructions indicate the part of the controller. L: receive your own position data. • If no repeater is found in a 160 kilometers range, screen 1, as shown to the right, will be displayed. • If the last received
  • Icom IC-7100 | Instruction Manual - Page 74
    "TX HISTORY" screen appears. ttTouch the repeater to use as your access repeater. • Example: "Hirano" • T he transceiver returns to the DR mode screen, and the selected repeater is set in "FROM." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 75
    specific station "Your Call Sign" setting (p. 5-16) Select the station call sign in the Your Call Sign memory. To select from RX History Setting from RX History (p. 5-17) When you receive you can switch the repeater group. ➥➥While in the DR mode, push QUICK (C), and then touch "Group Select." To
  • Icom IC-7100 | Instruction Manual - Page 76
    set in "TO." Example: M aking a Local area call by accessing the "Hirano" repeater. qqPush DR (C) to select the DR mode. transceiver returns to the DR mode screen, and "CQCQCQ" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 77
    Touch the destination repeater. • Example: "Hamacho" • T he transceiver returns to the DR mode screen, and "Hamacho" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display
  • Icom IC-7100 | Instruction Manual - Page 78
    to the DR mode screen, and "TOM" is displayed in "TO." After selecting a destination, you can select another station preset in your transceiver by rotating the Dial or [M-CH] (L). Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side
  • Icom IC-7100 | Instruction Manual - Page 79
    Touch "RX History." • The "RX HISTORY" screen appears. ttTouch the destination name or call sign. • Example: "TOM" • T he transceiver returns to the DR mode screen, and "TOM" is displayed in "TO." Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller
  • Icom IC-7100 | Instruction Manual - Page 80
    . ttTouch "TX History." • The "TX HISTORY" screen appears. yyTouch the destination name or call sign. • Example: "Dallas" • T he transceiver returns to the DR mode screen, and "Dal- las" is displayed in "TO." The L, R, C or D in the instructions indicate the part of the controller. L: Left side
  • Icom IC-7100 | Instruction Manual - Page 81
    8 characters, including spaces, and then touch [ENT](D). (Example: First, J, then M, then 1, then Z, then L, then K.) • T he transceiver returns to the DR mode screen, and "JM- 1ZLK" is displayed in "TO." • After programming, you can correct the call sign in the DIRECT INPUT (UR) screen. • T he
  • Icom IC-7100 | Instruction Manual - Page 82
    Program a call sign, and touch [ENT]. "K5TIT B" is set in "TO." The following settings are also correct. The repeater node* is input. "/" is input. In this case, the call sign is of a repeater for a Gateway call. *Although the repeater node letter is 'B' for 430 MHz band, 'A' is used in Japan
  • Icom IC-7100 | Instruction Manual - Page 83
    INSTALLATION AND CONNECTIONS Section 3 BASIC OPERATION Section 4 D-STAR INTRODUCTION Section 5 D-STAR OPERATION Section 6 SET MODE Section 7 INSTALLATION NOTES "AI" means "Advanced Instructions." "sec. MM" means section number. So when "(AI sec. MM)" is described on this manual, see the PDF
  • Icom IC-7100 | Instruction Manual - Page 84
    item. Left Display Center Right The L, R, C or D in the instructions indicate the part of the controller. L: Left side R: Right side C: Center bottom D: Display (Touch screen) DDThe Set mode settings qqPush SET(C) to enter the Set mode. wwIf the specified item is not displayed, touch [∫] or
  • Icom IC-7100 | Instruction Manual - Page 85
    MODE 6 Set mode items and Default settings ➥➥Call sign (AI sec. 9) ➥➥RX History (AI sec. 9) ➥➥MY Station (Section 4) ➥➥GPS (AI sec. 10) ➥➥SD Card (AI sec. 13) NOTE: The default settings shown below in bold are for the USA version. The default settings may differ, depending on your transceiver
  • Icom IC-7100 | Instruction Manual - Page 86
    the voice synthesizer. QSO/RX Log In this item, set the QSO/RX History Log options. QSO Log*1 OFF or ON Selects whether or not to make a communication log on the SD card. RX History Log*1 OFF or ON Selects whether or not to make a DV mode's re- ceive history log on the SD card. CSV Format
  • Icom IC-7100 | Instruction Manual - Page 87
    Select the function of the [RF/SQL] control. OFF, 10ms, 15ms, 20ms, 25ms or Sets the transmission's timing of the IC-7100 to 30ms prevent any external equipment that is connected from damage by the transmitted RF. OFF, 10ms, 15ms, 20ms, 25ms or See HF above. 30ms OFF, 10ms, 15ms, 20ms, 25ms
  • Icom IC-7100 | Instruction Manual - Page 88
    the notch function for the SSB mode. [NOTCH] Switch (AM) SSB/CW Sync Tuning CW Normal Side VOICE 1st Menu KEYER 1st Menu Speaker Out MIC AF Out RC MIC [F-1] [F-2] Mode Select Power OFF (With No Controller) REF Adjust Auto, Manual or Auto/Manual OFF or ON LSB or USB VOICE-Root or VOICE-TX KEYER
  • Icom IC-7100 | Instruction Manual - Page 89
    the USA version. The default settings may differ, depending on your transceiver version. Tone Control RX SSB RX HPF/LPF RX Bass RX Treble AM RX HPF/LPF RX Bass RX Treble FM RX HPF/LPF RX Bass RX Treble DV RX HPF/LPF WFM CW RX Bass RX Treble RX Bass RX Treble RX HPF/LPF RTTY RX HPF/LPF TX SSB
  • Icom IC-7100 | Instruction Manual - Page 90
    or closed). AF or IF Sets the [USB] connector and the [ACC] socket usage to received audio output or the IF output for DRM (Digital Radio Mondiale). 0 %~50 %~100 % Sets the audio output level at the [ACC] socket and the [USB] connector. 0 %~50 %~100 % Sets the IF output level at the [ACC
  • Icom IC-7100 | Instruction Manual - Page 91
    . Selects whether or not to automatically correct the time data by a received GPS sentence. Sets the time difference between UTC (Universal Time Coordinated) and the local time. Sets the clock display mode. Sets to automatically turn OFF the transceiver power after no operation is made during this
  • Icom IC-7100 | Instruction Manual - Page 92
    Clone Mode Clone Master Mode Touch Screen Calibration Reset Partial Reset All Reset In this item, set other options. Shows the transceiver's firmware version number. Reads or writes the CS-7100 data to or from the PC, and/or receives data from a Master transceiver. Writes your IC-7100 (Master
  • Icom IC-7100 | Instruction Manual - Page 93
    Section 7 INSTALLATION NOTES Installation notes 7-2 Section 1 panel description Section 2 INSTALLATION AND CONNECTIONS Section 3 BASIC OPERATION Section 4 D-STAR INTRODUCTION Section 5 D-STAR OPERATION Section 6 SET MODE Section 7 INSTALLATION NOTES 7-1
  • Icom IC-7100 | Instruction Manual - Page 94
    is not active for long periods of time. Some radio licenses will require that a timer circuit automatically cuts off the transmitter after 1-2 minutes etc. Similarly some modes of transmission, SSB, CW, AM etc. have a lower 'average' output power and the assessed risk is even lower. 7-2
  • Icom IC-7100 | Instruction Manual - Page 95
    MEMO I
  • Icom IC-7100 | Instruction Manual - Page 96
    A-7085H-1EX-0a Printed in Japan © 2013 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
INSTRUCTION MANUAL
i7100
HF/VHF/UHF ALL MODE TRANSCEIVER
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
WARNING:
MODIFICATION OF THIS DEVICE TO RECEIVE
CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS
PROHIBITED UNDER FCC RULES AND FEDERAL LAW.