Icom IC-7100 Instruction Manual - Page 17

Controller — Rear and bottom panels, STAND, SCREW HOLE FOR STAND - mobile

Get Icom IC-7100 PDF manuals and user guides View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Controller - Rear and bottom panels Bottom panel Rear panel 1 PANEL DESCRIPTION qw e r Speaker q HEADPHONE/SPEAKER JACK [PHONES/SP] Plug in standard stereo headphones (impedance: 8 to 16 ø). • Output power: More than 5 mW with an 8 ø load. • When headphones are connected, the internal speaker, and any external speaker, are disabled. • W hen the [PHONES/SP] switch (y) on the bottom panel is set to the SPEAKER position, an external speaker can be used instead of headphones. This is convenient for mobile or outdoor operation. w ELECTRONIC KEYER JACK [ELEC-KEY] Plug in a bug or paddle type key to use the internal electronic keyer for CW operation. (AI sec. 4) • Set the keyer type to ELEC-KEY, BUG-KEY or Straight key in the "Keyer Type" item of the "KEYER SET" mode. • When a straight key is connected, "Straight key" must be selected in the "Keyer Type" item of the "KEYER SET" mode. (AI sec. 4) • A straight key jack is located on the rear panel. See [KEY] on pages 1-15 and 2-5. • Y ou can reverse the keyer paddle polarity (dot and dash) in the "Paddle Polarity" item of the "KEYER SET" mode. (AI sec. 4) • Four keyer memory channels are available for your convenience. (AI sec. 4) (dot) (com) (dash) A standard 3.5(d) mm/ 1⁄8 inch plug yu i t e MICROPHONE CONNECTOR [MIC] Plug in the supplied or an optional microphone. • See AI sec. 21 for appropriate microphones. • See p. 1-17 for microphone connector information. • T he optional OPC-589 cable can be used to connect an 8-pin microphone such as the SM-30 or SM-50. • A microphone connector is also available on the Main unit. DO NOT simultaneously connect two microphones. r MAIN UNIT CONNECTOR [MAIN UNIT] Connects to the Main unit using with the supplied OPC-2253 Control cable. • T he OPC-2253 Control cable is 3.5 meter (11.5 feet) long. DO NOT use any third party's Ethernet cables. t STAND The length of the stand can be adjusted in two steps. • Adjust to the length not to incline back when you operate the Front panel. y PHONES/SPEAKER SWITCH [PHONE/SP] Selects the [PHONES/SP] jack to connect a Head- phones or external speaker. u SCREW HOLE FOR STAND Accepts the screw of a tripod stand. (Third party product.) i SCREW HOLES FOR CONTROLLER BRACKET Accepts the screws of the optional MBA-1 Controller bracket. • T he MBA-1 is required to install to the optional MBF-1 Mounting base. 1-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1
PANEL DESCRIPTION
1-13
Controller — Rear and bottom panels
q
HEADPHONE/SPEAKER JACK [PHONES/SP]
Plug in standard stereo headphones (impedance: 8
to 16
ø
).
• Output power: More than 5 mW with an 8
ø
load.
• When headphones are connected, the internal speaker,
and any external speaker, are disabled.
• When the [PHONES/SP] switch (
y
) on the bottom panel
is set to the SPEAKER position, an external speaker can
be used instead of headphones. This is convenient for
mobile or outdoor operation.
w
ELECTRONIC KEYER JACK [ELEC-KEY]
Plug in a bug or paddle type key to use the internal
electronic keyer for CW operation. (AI sec. 4)
• Set the keyer type to ELEC-KEY, BUG-KEY or Straight
key in the “Keyer Type” item of the “KEYER SET” mode.
• When a straight key is connected, “Straight key” must be
selected in the “Keyer Type” item of the “KEYER SET”
mode. (AI sec. 4)
• A straight key jack is located on the rear panel. See [KEY]
on pages 1-15 and 2-5.
•You can reverse the keyer paddle polarity (dot and dash)
in
the “Paddle Polarity” item
of
the
“KEYER SET”
mode.
(
AI sec. 4
)
• Four keyer memory channels are available for your con
-
venience. (AI sec. 4)
(dot)
(com)
(dash)
A standard 3.5(d) mm/
1
⁄
8
inch plug
e
MICROPHONE CONNECTOR [MIC]
Plug in the supplied or an optional microphone.
• See AI sec. 21 for appropriate microphones.
• See p. 1-17 for microphone connector information.
• The optional OPC-589 cable can be used to connect an
8-pin microphone such as the SM-30 or SM-50.
• A microphone connector is also available on the Main
unit.
DO NOT
simultaneously connect two microphones.
r
MAIN UNIT CONNECTOR [MAIN UNIT]
Connects to the Main unit using with the supplied
OPC-2253 Control cable.
• The OPC-2253 Control cable is 3.5 meter (11.5 feet)
long.
DO NOT
use any third party’s Ethernet cables
.
t
STAND
The length of the stand can be adjusted in two
steps.
• Adjust to the length
not to incline back when you operate
the Front panel.
y
PHONES/SPEAKER SWITCH [PHONE/SP]
Selects the [PHONES/SP] jack to connect a Head-
phones or external speaker.
u
SCREW HOLE FOR STAND
Accepts the screw of a tripod stand. (Third party
product.)
i
SCREW HOLES FOR CONTROLLER BRACKET
Accepts the screws of the optional MBA-1 Controller
bracket.
• The MBA-1 is required to install to the optional MBF-1
Mounting base.
Bottom panel
Rear panel
qw e
r
Speaker
t
u
i
y