Icom IC-9700 Instruction Manual basic - Page 67
USB AF/IF Output
View all Icom IC-9700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 67 highlights
SET MODE 8 MENU » SET > Connectors > USB AF/IF Output MENU » SET > Connectors > MOD Input Output Select Selects the signal output from [USB]. ••AF: An AF signal is output. ••IF: A 12 kHz IF signal is output. (Default: AF) ACC MOD Level (Default: 50%) USB MOD Level LAN MOD Level 1 (Default: 50%) (Default: 50%) Sets the modulation input level of each interface. 2 AF Output Level (Default: 50%) Sets the AF output level of [USB], when "Output Select" of USB is set to "AF." AF SQL (Default: OFF (Open)) Selects whether or not to output the audio from [USB], according to the squelch state, when "Output Select" of USB is set to "AF." ••OFF (Open): The squelch is always opened regardless of the transceiver's squelch level. ••ON: The squelch opens and closes, according to the transceiver's squelch level. AF Beep/Speech... Output (Default: OFF) Sets the Beep and Speech audio output setting of [USB], when "Output Select" of USB is set to "AF." ••OFF: The beep and speech audio are not output. ••ON: The beep and speech audio are output. IF Output Level (Default: 50%) Sets the IF output level of [USB], when "Output Select" of USB is set to "IF." MENU » SET > Connectors > LAN AF/IF Output DATA OFF MOD DATA MOD (Default: MIC,ACC) (Default: ACC) 3 In the SSB, AM, or FM mode, selects the connector(s) to input the modulation signal when the data mode is 4 OFF, or ON. 5 MENU » SET > Connectors > ACC SEND Output 6 144M 430M (Default: ON) (Default: ON) 7 1200M (Default: ON) Selects whether or not to switch the SEND terminal 8 output level of [ACC] to the Low level during transmitting. 9 ••OFF: Does not switch to the Low level. ••ON: Switches to the Low level. 10 MENU » SET > Connectors > USB SEND/Keying 11 TIP: This is the setting for the terminal used for data 12 communication when you operate the transceiver from the software on the PC. 13 When you connect the transceiver to a PC with a USB cable, 2 COM ports are recognized on the PC. 14 To confirm USB (A)/USB (B), open the COM port properties, and confirm the "Value" of the "Details" tab. 15 Output Select Selects the signal output from [LAN]. ••AF: An AF signal is output. ••IF: A 12 kHz IF signal is output. (Default: AF) AF SQL (Default: ON) Selects whether or not to output the audio from [LAN], according to the squelch state, when "Output Select" of LAN is set to "AF." ••OFF (Open): The squelch is always opened regardless of the transceiver's squelch level. ••ON: The squelch opens and closes, according to the transceiver's squelch level. USB SEND 16 (Default: OFF) Sets the USB terminal of the transceiver to receive the SEND signal from the software on the PC. 17 Select the same terminal as the terminal set by the software. LYou cannot select the terminal which is already selected in 18 the "USB Keying (CW)" or "USB Keying (RTTY)" item. 19 USB Keying (CW) (Default: OFF) Sets the USB terminal of the transceiver to receive the 20 CW Keying signal from the software on the PC. Select the same terminal as the terminal set by the 21 software. LYou cannot select the terminal which is already selected in the "USB SEND" or "USB Keying (RTTY)" item. USB Keying (RTTY) (Default: OFF) Sets the USB terminal of the transceiver to receive the RTTY Keying signal from the software on the PC. Select the same terminal as the terminal set by the software. LYou cannot select the terminal which is already selected in the "USB SEND" or "USB Keying (CW)" item. 8-12