Panasonic AG-HMX100 Operating Instructions - Page 27

Basic Operation • When the 3D mode is [OFF] ( page Vol.2-25), the system format of this unit is the one set in the [VIDEO FORMAT] submenu of the [SETUP] menu. When the 3D mode is other than [OFF], the system format of this unit is the one set under the [3DFORMAT] item in the [3D] submenu of the [SETUP] menu. 2 Use the rotary 3 control to select the audio input (of the SDI input selected in Step 1) which you want to assign the L channel by setting [L‑CH] to the desired audio input number. Setting the Bus [BUS] The [BUS] submenu of the [SETUP] menu is used to set the output method of this unit to either of the following: • AB bus system: Switches between video A and video B. • Program/Preset system: Switches between program output (base video) and preset output (video used as effects). When the Program/Preset system is selected, the A/PROG bus source selector button corresponding to the source used for the transition pattern and output from a PGM connector is necessarily lighted or flashes. Thus, an input source that you want to display next can be selected only with the B/PRESET bus source selector buttons.  For more information about the input source selection operation, see page 33. Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5 BUS TYPE AB AB PRG/PRE 3 Use the rotary 4 control to select the audio input (of the SDI input selected in Step 1) which you want to assign the R channel by setting [R‑CH] to the desired audio input number. 4 Repeat Steps 1 to 3 to assign each audio input of SDI inputs 1 to 4 to the L channel or R channel.  NOTE The set channel is stored in memory separately between the cases in which the system format is SD and HD ( page 19), and is called according to the format when the system format is changed. To hide the audio level meter during multi-view output Set [OSD] to [OFF] using the rotary 5 control. The factory default setting is [ON], in which the audio level meter is displayed when the multi-view output is monitored. Set [TYPE] to [AB] (AB bus system) or [PRG/PRE] (Program/Preset system) using the rotary 2 control. The factory default setting is [AB]. Setting Audio Channels [AUDIO CH] The [AUDIO CH] submenu of the [SETUP] menu is used to select L channel or R channel of this unit for each audio channel of the selected SDI input source. When the system format is HD ( page 19), audio channels 1 to 8 can be assigned. When the system format is SD, audio channels 1 to 4 can be assigned. Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5 AUDIO CH L-CH R-CH OSD CH SDI1 1 2 ON SDI1 SDI2 SDI3 SDI4 1-8 (1-4) 1-8 (1-4) OFF ON 1 Set [CH] to one of [SDI1], [SDI2], [SDI3], or [SDI4] (SDI inputs 1 to 4) using the rotary 2 control. Setting the Audio Faders [AUDIO FADER] The audio input level is adjusted with the SOURCE 1/5, 2/6, 3/7, 4/8 faders (audio faders). When adjusting the audio level of input sources 5 to 8, operate the corresponding fader while holding down the SHIFT key. Operate the AUX fader to adjust the AUX input level and the MIC fader to adjust the MIC input level. The operation of the audio faders, AUX fader, and MIC fader can be set from the [AUDIO FADER] submenu of the [SETUP] menu. Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5 AUDIO SOURCE AUX/MIC FADER BUS SEP1 PAIR CP PAIR BUS SEP1 BUS SEP2 12 PAIR 12 SEPA. PAIR SEPA. 27