Sony UWPV6/4244 Operating Instructions - Page 35

Power Supply, Inserting the batteries

Get Sony UWPV6/4244 PDF manuals and user guides View all Sony UWPV6/4244 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Power Supply This section explains the power supply for each component. Diversity tuner module (URXM2) When incorporated into another component (e.g., MB-X6, SRP-X500P, etc.), the tuner module draws its power from that component. For details on the power supply to the diversity tuner module, refer to the operating instructions of the component in which the diversity tuner module is installed. Body-pack transmitter (UTXB2), hand-held microphone (UTX-H2), plug-on transmitter (UTX-P1), and portable diversity tuner (URX-P2) These components can be powered by two LR6 (size AA) alkaline batteries. Details on inserting the batteries and the battery condition indication are given below: Note The manganese batteries cannot draw sufficient performance from the component. Be sure to use the alkaline batteries. Inserting the batteries Body-pack transmitter (UTXB2)/portable diversity tuner (URX-P2) The procedure below uses the body-pack transmitter (UTX-B2) in the illustrations. Batteries can also be inserted in the portable diversity tuner (URX-P2) in the same manner. 1 Slide the battery-compartment catches inward (in the direction of the arrows b B) to take out the battery holder. 2 Insert the batteries into the battery compartment by matching their polarities to the indications inside the compartment. Then, set the battery holder in the original position. Note Taking out the battery compartment during signal transmission may cause high noise. Be sure to turn off the component before taking out the battery compartment. 35 Power Supply

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
35
Power Supply
Power Supply
This section explains the power supply for
each component.
Diversity tuner module (URX-
M2)
When incorporated into another component
(e.g., MB-X6, SRP-X500P, etc.), the tuner
module draws its power from that
component.
For details on the power supply to the diversity tuner
module, refer to the operating instructions of the
component in which the diversity tuner module is
installed.
Body-pack transmitter (UTX-
B2), hand-held microphone
(UTX-H2), plug-on transmitter
(UTX-P1), and portable
diversity tuner (URX-P2)
These components can be powered by two
LR6 (size AA) alkaline batteries. Details on
inserting the batteries and the battery
condition indication are given below:
The manganese batteries cannot draw
sufficient performance from the
component. Be sure to use the alkaline
batteries.
Inserting the batteries
Body-pack transmitter (UTX-
B2)/portable diversity tuner
(URX-P2)
The procedure below uses the body-pack
transmitter (UTX-B2) in the illustrations.
Batteries can also be inserted in the portable
diversity tuner (URX-P2) in the same
manner.
1
Slide the battery-compartment catches
inward (in the direction of the arrows
b
B
) to take out the battery holder.
2
Insert the batteries into the battery
compartment by matching their
polarities to the indications inside the
compartment. Then, set the battery
holder in the original position.
Taking out the battery compartment during
signal transmission may cause high noise.
Be sure to turn off the component before
taking out the battery compartment.
Note
Note