Sony UWPV6/4244 Operating Instructions - Page 42

Operation

Get Sony UWPV6/4244 PDF manuals and user guides View all Sony UWPV6/4244 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

To install a diversity tuner module (URX-M2) into the optional SRP-X500P Powered Mixer The SRP-X500P Powered Mixer (not supplied) can accommodate up to two diversity tuner modules (URX-M2). For details on installation procedure, refer to the Operating Instructions supplied with the SRPX500P. Remove the protection panel (large) from the SRP-X500P. Inspect the top and bottom sides of the diversity tuner module and insert it into the slot. To uninstall the tuner module Pull the latch securing the tuner module to the side and pull out the tuner module. Latch Operation The procedure below is the same for all UWP series transmitters (UTX-B2/H2/P1) and tuners (URXP2/M2). 1 Make all necessary connections on the tuner. For examples of UWP series component connections, see "System Configurations" on page 50. 2 Turn on the tuner. The parameters that were in the display section when the tuner was last turned off appear again. Note Noise will be produced when the tuner is turned on. Before turning on the tuner, turn down the volume of the equipment connected to the tuner. 3 Set the reception channel on the tuner. Switch the channel on the tuner with the transmitter turned off and select the channel where the RF indicator does not turn on. For details on setting the reception channel, see "Setting the reception channel" on page 43. 4 Set the transmission channel on the transmitter, and then turn off the unit. For details on setting the transmission channel, see "Setting the transmission channel" on page 47. 5 Turn on the transmitter. 42 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
42
Operation
To install a diversity tuner
module (URX-M2) into the
optional SRP-X500P Powered
Mixer
The SRP-X500P Powered Mixer (not
supplied) can accommodate up to two
diversity tuner modules (URX-M2).
For details on installation procedure, refer to the
Operating Instructions supplied with the SRP-
X500P.
Remove the protection panel (large) from
the SRP-X500P. Inspect the top and bottom
sides of the diversity tuner module and
insert it into the slot.
To uninstall the tuner module
Pull the latch securing the tuner module to
the side and pull out the tuner module.
Operation
The procedure below is the same
for all UWP series transmitters
(UTX-B2/H2/P1) and tuners (URX-
P2/M2).
1
Make all necessary connections on the
tuner.
For examples of UWP series component
connections, see “System Configurations” on
page 50.
2
Turn on the tuner.
The parameters that were in the display
section when the tuner was last turned
off appear again.
Noise will be produced when the tuner
is turned on. Before turning on the
tuner, turn down the volume of the
equipment connected to the tuner.
3
Set the reception channel on the tuner.
Switch the channel on the tuner with
the transmitter turned off and select the
channel where the RF indicator does
not turn on.
For details on setting the reception channel,
see “Setting the reception channel” on
page 43.
4
Set the transmission channel on the
transmitter, and then turn off the unit.
For details on setting the transmission
channel, see “Setting the transmission
channel” on page 47.
5
Turn on the transmitter.
Latch
Note