Sony UWPV6/4244 Operating Instructions - Page 45

Searching the available channels within the group (Clear Channel Scan)

Get Sony UWPV6/4244 PDF manuals and user guides View all Sony UWPV6/4244 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

operate normally. Wait a few seconds before turning it on again. Searching the available channels within the group (Clear Channel Scan) The procedure below can be performed with the portable diversity tuner (URX-P2) only. Available channels within the specified channel group can be searched. Before performing this procedure, select the channel group. For details on channel group selection, see "Setting the reception channel" on page 43. 1 While pressing down the SET button, press the + button. Keep both buttons pressed down. 2 Release the SET button and the + button after "SCAN +" appears and starts flashing. 3 Press the + button. The tuner starts to scan through the selected channel group. When available channels are found, the first channel number among the available channels flashes in the display. To display the next available channel number Press the + button. To cancel searching Press the - button. The display shows the flashing "SCAN +" again. To re-select the channel group Press the SET button again to display the flashing channel group indication, then select the channel group. And then, start from step 1. 4 While the desired channel number is flashing, leave the tuner for about 10 seconds or press down the SET button for more than one second. Search finishes. The selected channel number stops flashing and the selection is stored in memory. To start searching while performing settings While the display section parameters are flashing, press the SET button repeatedly until "SCAN +" appears and starts flashing. Then, start from step 3 above. Selecting the channels on multiple tuners automatically The procedure below can be performed with the diversity tuner module (URX-M2) only. When multiple diversity tuner modules (URX-M2) are installed into the MB-X6 to perform simultaneous multiple-channel operation, select the channel group on the tuner module installed into the slot 1 of the MB-X6, then all the tuner modules installed into the MB-X6 can be set to different channels within the selected channel group. 1 Turn off all the microphones and transmitters. 45 Tuner Settings

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
45
Tuner Settings
operate normally. Wait a few seconds
before turning it on again.
Searching the available
channels within the group
(Clear Channel Scan)
The procedure below can be
performed with the portable
diversity tuner (URX-P2) only.
Available channels within the specified
channel group can be searched.
Before performing this procedure, select
the channel group.
For details on channel group selection, see “Setting
the reception channel” on page 43.
1
While pressing down the SET button,
press the + button.
Keep both buttons pressed down.
2
Release the SET button and the +
button after “SCAN
+” appears and
starts flashing.
3
Press the + button.
The tuner starts to scan through the
selected channel group. When
available channels are found, the first
channel number among the available
channels flashes in the display.
To display the next available
channel number
Press the + button.
To cancel searching
Press the – button. The display shows
the flashing “SCAN
+” again.
To re-select the channel group
Press the SET button again to display
the flashing channel group indication,
then select the channel group. And
then, start from step
1
.
4
While the desired channel number is
flashing, leave the tuner for about 10
seconds or press down the SET button
for more than one second.
Search finishes. The selected channel
number stops flashing and the
selection is stored in memory.
To start searching while
performing settings
While the display section parameters are
flashing, press the SET button repeatedly
until “SCAN
+” appears and starts flashing.
Then, start from step
3
above.
Selecting the channels on
multiple tuners
automatically
The procedure below can be
performed with the diversity tuner
module (URX-M2) only.
When multiple diversity tuner modules
(URX-M2) are installed into the MB-X6 to
perform simultaneous multiple-channel
operation, select the channel group on the
tuner module installed into the slot
1
of
the MB-X6, then all the tuner modules
installed into the MB-X6 can be set to
different channels within the selected
channel group.
1
Turn off all the microphones and
transmitters.