Sony UWPV6/4244 Operating Instructions - Page 55

Troubleshooting

Get Sony UWPV6/4244 PDF manuals and user guides View all Sony UWPV6/4244 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Troubleshooting If you have any problem using the UWP series components, use the following checklist. Should any problem persist, consult your Sony dealer. Symptom Meanings Remedy The unit does not The polarity orientation of the Insert the batteries with the correct turn on.1) batteries in the battery compartment is incorrect. polarity orientation. The batteries are exhausted. Replace the batteries with new ones. The battery terminals in the Clean the + and - terminals with a transmitter are dirty. cotton swab. The batteries become drained quickly.1) The batteries are exhausted. Replace the batteries with new ones. Manganese batteries are being used. Use alkaline batteries. The battery life of a manganese battery is less than half that of an alkaline battery. The UWP series components is being used under cold conditions. The batteries drain quickly under cold conditions. The channel cannot be changed. An attempt was made to Restart the unit while holding down change the channel by the SET button. Then change the pressing the SET button only. channel with the + and - buttons. There is no sound. The channel setting on the transmitter is different from that on the tuner. Use the same channel setting on both the transmitter and tuner. The RF indicator on the tuner Confirm that the transmitter is does not turn on. turned on. The line input is selected on Select the microphone input on the the transmitter.2) transmitter. The tuner module is installed into/uninstalled from the MBX6/SRP-X500P while the MB-X6/SRP-X500P is turned on. Turn off the MB-X6/SRP-X500P. Then, turn it on again. 55 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
55
Troubleshooting
Troubleshooting
If you have any problem using the UWP series components, use the following checklist.
Should any problem persist, consult your Sony dealer.
Symptom
Meanings
Remedy
The unit does not
turn on.
1)
The polarity orientation of the
batteries in the battery
compartment is incorrect.
Insert the batteries with the correct
polarity orientation.
The batteries are exhausted.
Replace the batteries with new
ones.
The battery terminals in the
transmitter are dirty.
Clean the + and – terminals with a
cotton swab.
The batteries
become drained
quickly.
1)
The batteries are exhausted.
Replace the batteries with new
ones.
Manganese batteries are
being used.
Use alkaline batteries. The battery
life of a manganese battery is less
than half that of an alkaline battery.
The UWP series
components is being used
under cold conditions.
The batteries drain quickly under
cold conditions.
The channel
cannot be
changed.
An attempt was made to
change the channel by
pressing the SET button only.
Restart the unit while holding down
the SET button. Then change the
channel with the + and – buttons.
There is no sound.
The channel setting on the
transmitter is different from
that on the tuner.
Use the same channel setting on
both the transmitter and tuner.
The RF indicator on the tuner
does not turn on.
Confirm that the transmitter is
turned on.
The line input is selected on
the transmitter.
2)
Select the microphone input on the
transmitter.
The tuner module is installed
into/uninstalled from the MB-
X6/SRP-X500P while the
MB-X6/SRP-X500P is turned
on.
Turn off the MB-X6/SRP-X500P.
Then, turn it on again.