ZyXEL U-336R User Guide - Page 150

Command Echo Problems

Get ZyXEL U-336R PDF manuals and user guides View all ZyXEL U-336R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

3. You may have typed the commands when your modem was in data state instead of the command state. To switch from data state to command state, type the escape sequence code +++. To return to the data state, type ATO and press Enter. Problem You typed an AT command, but did not receive an OK or 0 result code. Solutions 1. Your communications software may be using a different COM port than your modem. Be sure both the software and your modem are addressing the same COM port. 2. The E0 and Q1 commands may be in effect, disabling echo and result codes. To verify this in terminal mode, type AT&V0 and press Enter with the modem in command state to view the currently active settings. To enable echo and result codes, type AT E1 Q0 and press Enter. 3. You may have typed the commands when your modem was in the data state instead of the command state. To switch from data state to command state, type the escape sequence code +++. To return to data state, type ATO and press Enter. Problem You receive the ERROR result code after typing an AT command. Solution You may have typed a command that is not recognized by your modem or communications software. Command Echo Problems Problem You do not see any typed characters on your computer screen. 136 Diagnostics & Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
136
Diagnostics & Troubleshooting
3.
You may have typed the commands when your modem was in data
state instead of the command state. To switch from data state to
command state, type the escape sequence code +++. To return to
the data state, type ATO and press Enter.
Problem
You typed an AT command, but did not receive an OK or 0 result
code.
Solutions
1.
Your communications software may be using a different COM port
than your modem. Be sure both the software and your modem are
addressing the same COM port.
2.
The E0 and Q1 commands may be in effect, disabling echo and
result codes. To verify this in terminal mode, type AT&V0 and
press Enter with the modem in command state to view the currently
active settings. To enable echo and result codes, type AT E1 Q0
and press Enter.
3.
You may have typed the commands when your modem was in the
data state instead of the command state. To switch from data state
to command state, type the escape sequence code +++. To return
to data state, type ATO and press Enter.
Problem
You receive the ERROR result code after typing an AT command.
Solution
You may have typed a command that is not recognized by your modem
or communications software.
Command Echo Problems
Problem
You do not see any typed characters on your computer screen.